EN 2940-1995 en Aerospace Series - Screws 100 Degree Countersunk Head Offset Cruciform Recess Threaded to Head in Heat Resisting Steel FE-PA92HT (A286) Silver Plated - Classificati.pdf

《EN 2940-1995 en Aerospace Series - Screws 100 Degree Countersunk Head Offset Cruciform Recess Threaded to Head in Heat Resisting Steel FE-PA92HT (A286) Silver Plated - Classificati.pdf》由会员分享，可在线阅读，更多相关《EN 2940-1995 en Aerospace Series - Screws 100 Degree Countersunk Head Offset Cruciform Recess Threaded to Head in Heat Resisting Steel FE-PA92HT (A286) Silver Plated - Classificati.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、CEN EM*2949 95 3404589 O323654 Lb2 D BRITISH STANDARD AEROSPACE SERIES Screws, 100“ countersunk head, offset cruciform recess, threaded to head, in heat resisting steel FE-PA92HT (A 286), silver plated - Classification: 900 MPa (at ambient temperature)/65O0C The European Standard EN 2940 : 1995 has

2、the status of a British Standard ICs 49 040 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGBr LAW BS EN 2940 : 1996 CEN EN*2940 95 3404589 O323655 OT9 m BS EN 2940 : 1996 Committees responsible for this British Standard The preparation of this British Standard was entrusted to Techn

3、ical Committee ACW12, Aerospace fasteners and fastening systems, upon which the following bodies were represented Association of Electronics, Telecommunications and Business Equipment Industries British Industrial Fasteners Federation Ministry of Defence Society of British Aerospace Companies Ltd. T

4、his British Standard, having been prepared under the direction of the Engineering Sector Board, was published under the authority of the Standards Board and comes into effect on 15 Apd 1996 O BSI 1996 Amendments issued since publication Arnd.No. Date I The following BSI references relate to the work

5、 on this standard Committee reference ACW12 Draft for comment W6307 DC ISBN O 580 25617 4 CEM EN+2940 %5 U 3YwW39 0123h56 T35 BS EN 2940 : 1996 Contents Page Committees responsible Inside front cover National foreword 11 Foreword 2 Specification 1 Scope 2 Normative references 3 Requiredcharacteristi

6、cs 4 Designation 6 Markjng 6 TechnicalsDecification O ES1 1996 i CEN EN*29i60 45 U 3404583 CIL23657 971 BS EN 2940 : 1996 National foreword This British Standard has been prepared by Technical Committee ACW12 and is the English language version of EN 2940 : 1995Amspace series - Screws, 100“ counters

7、unk head, offset m.u$form recess, threaded to had, in heat resisting steel FE-PA92HT (A286), silverplated - Classification: 900 MPa (at ambient temperature)/65OoC, published by the European Committee for Standardization (CEN). EN 2840 : 1995 was produced as a result of international discussions in w

8、hich the United Kingdom took an active part. Cross-references The British Standards corresponding to the European Standards referred to in the text are identical in number and title with those given in clause 2, with the exception of EN 2398, EN 2399, EN 2424, EN 2786 and EN 3043 for which no corres

9、ponding British Standards exist. The British Standards corresponding to the international standards referred to in the text are as follows. Publication referred to Corresponding British Standard BS 2A 231 : 1993 RoUed threads for bolts -Lead and runout requirements BS 6293 Aerospace - MJ threads Par

10、t 2 : 1994 Limit dimensions for bolts and nuts BS A 297 : 1987 Specification for internal drive, offset cruciform recess (Torq-Set (RI) for rotarg fastening devices -Metric series IS0 3353 : 1992 IS0 58552 : 1988 IS0 7994 : 1985 Compliance with a British Standard does not of itself confer immunity f

11、rom legal obligations. O BSI 1996 CEN ENa2940 95 m 31)04589 0323658 808 EUROPEAN STANDARD NORME EUROPENNE EUROPAISCHE NORM EN 2940 October 1995 ICs 49.040 Descriptors: Aircraft industry, fastener, screw, countersunk head screw, cross-recessed screw, heat resistant steel, silver coating, classificati

12、on, chension, surface treatment, screw thread, designation English version Aerospace series - Screws, 100“ countersunk head, offset cruciform recess, threaded to head, in heat resisting steel FE-PA92HT (A286), silver plated - Classification: 900 MPa (at ambient temperature)/65O0C Srie arospatiale -

13、Vis tte fraise 100“ empreinte cruciforme dporte, filetes sous tte, en acier rsistant chaud FE-PA92HT (A286), argentes - Classification: 900 MPa ( temprature ambiante)/65O0C Raumtemperatur)/65O0C Luft- und Raumfahrt - 100“ Senkschrauben, Flgelkreuzschlitz, Gewinde bis Kopf, aus hochwarmfestem Stahl F

14、E-PA92HT (A286), versilbert - Klasse: 900 MPa (bei This European Standard was approved by CEN on 1995-04-13. CEN members are bound to comply with the CENKENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alterat

15、ion. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English French, German). A version in any other language made by translati

16、on under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, N

17、etherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europisches Komitee fur Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels O 1995 AU rights of reproduction and communication in any fo

18、rm and by any means reserved in all countries to CEN and its members Ref. No. EN 2940 : 1995 E CEN EN*274O 75 m 3404587 0123657 744 m Page 2 EN 2940 : 1995 Foreword This European Standard has been prepared by the European Association of Aerospace Manufacturem Afer inquiries and votes carried out in

19、accordance with the rules of this Association, this Standard has successively received the approval of the National Associations and the Official Services of the member countries of AECMA, prior to its presentation to CEN. This European Standard shaU be given the status of a national standard, eithe

20、r by publication of an identical text or by endorsement, at the latest by Aprii 1996, and conflicting national standards shall be withdrawn at the latest by Apd 1996. According to the CENICENELEC Internal Regulations, the following countries are bound to implement this European Standard: Austria, Be

21、lgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland, United Kingdom. (AECMA). O BSI 1996 CEN EN*294O 95 3404589 0123660 4bb Page 3 EN 2940 : 1995 1 Scope This standard specifies the characteristics of screws

22、 with 1 OOo countersunk head with offset cruciform recess, threaded to head, in FE-PA92HT, silver plated, for aerospace applications. Classification : 900 MPa ) I650 OC 2, 2 Normative references This European Standard incorporates by dated or undated reference provisions from other publications. The

23、se normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undat

24、ed references the latest edition of the publication referred to applies. IS0 3353 Aerospace - Rolled threads for bolts - Lead and runout requirements IS0 5855-2 Aerospace - MJ threads - Part 2 : Limit dimensions for bolts and nuts IS0 7994 Aerospace - Internal drive, offset cruciform recess (Torq-Se

25、t i for rotary fastening devices - Metric series EN 2398 Heat resisting steel FE-PA92-HT - R, 2 900 MPa - Bars for machined bolts - D I 25 mm - Aerospace series 3, EN 2399 Heat resisting steel FE-PA92-HT - R, 2 900 MPa - Bars for forged bolts - D S 25 mm - Aerospace series 3, EN 2424 EN 2786 Aerospa

26、ce series - Marking of aerospace products Aerospace series - Electrolytic silver plating of fasteners 4, EN 3043 Aerospace series - Fasteners, externally threaded, in heat resisting steel FE-PA92HT (A2861 - Classification : 900 MPa / 650 OC - Manufacturing method optional - Technical specification 4

27、, 3 Required characteristics 3.1 Configyration - Dimensions - Tolerances - Masses See figure 1 and tables 1 and 2. Dimensions and tolerances are in millimetres. They apply after silver plating. 3.2 Materials EN 2398 or EN 2399 3.3 Surface treatment EN 2786 Thickness : - thread : 3 pm to 6 pm shall b

28、e measured at the pitch diameter ; - other areas may show complete coverage, without thickness requirement. 1) Minimum tensile strength of the material at ambient temperature 2) Maximum test temperature of the parts 3) Published as AECMA Standard at the date of publication of this standard 4) Publis

29、hed as AECMA Prestandard at the date of publication of this standard - CEN EN*2LiO 95 1111 3404589 OL2366L 3T2 Thread D E2) F 0 H2) K P Q R W Recair O number Code Designation f O, 13 min. min. - 0.08 nom. TOI. max. mn. max. min. IS0 7994 -030 MJ3xO,5-4h6h 2.68 6 5,4 4,5 1,4 0,06 0,63 2.3 O 2.4 2.15

30、R3 , 040 W4x0,7-4h6h 3.55 8 7.2 5.78 1,9 0,08 0,93 3 -0,5 Og2 3.27 2.92 R4 O50 MJ5x0,8-4h6h 4.48 10 9 7.71 2.4 0,1 0.96 3.4 f 0,5 0.5 0.3 3.98 3.58 R5 1) In accordance with IS0 5855-2 2) Corresponds to maximum condition. - Page 4 EN 2940 : 1995 y0yR*) Values apply before silver plating. (HI- P* L-Tz

31、Lo.o8A1 Not concave Remove sharp edges 0,l to 0,4 I -Conforms to I Thread - -K Marking +cess conforms Figure 1 Table 1 Page 5 EN 2940 : 1995 Table 2 Thread code CEN EN*29YQ 95 3YOY589 QiJ23bb3 175 M Description block Page 6 EN 2940 : 1995 Identity block 4 Designation Thread code 030 and 040 050 NOTE

32、 : If necessary, the code 19005 shall be placed between the description block and the identitv block. F C 5 Marking EN 2424, style see table 3 and as indicated on figure 1. Table 3 6 Technical specification EN 3043 CEN EN*:2940 95 340a1589 Ul123bb4 DOL m BS EN 2940 : 1996 List of references See nati

33、onal foreword. CEN ENa2940 95 U 3404589 OL23bb5 T48 BS EN 2940 : 1996 BSI 389 Chiswick High Road London w4 4AL BSI - British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international

34、 level. It is incorporated by Royal Charter. Contract requirements A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Revisions British Standards are updated by amendment or revision. Us

35、ers of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secre

36、tary of the responsible technical committee, the identity of which can be found on the inside front cover. Tel: 0181 996 9000; Fax: 0181 996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buyi

37、ng standards Orders for ali BSI, international and foreign standards publications should be addressed to Customer Services, Sales Department at Chiswick Tel: 0181 996 7000; Fax: 0181 996 7001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of tho

38、se that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library, the Standardiine Database, the BSI Information Technology Service (BITS) and its Tech

39、nical Help to Exporters Service. Contact the information Department at Chiswick Tel 0181 996 7111; Fax: 0181 996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benef

40、its contact Customer Services, Membership at Chiswick Tel 0181 996 7002;Fax: 0181 996 7001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs

41、 and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means - electronic, photocopying, recording or otherwise - without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard,

42、 of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. if permission is granted, the tem may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager, BSI, 389 Chiswick High Road, London W4 4AL. SBN O 680 25517 4 ACW12