EN 1464-2010 en Adhesives - Determination of peel resistance of adhesive bonds - Floating roller method《粘合剂 粘结的抗剥离性测定 浮辊法［代替 CEN EN 1967］》.pdf

《EN 1464-2010 en Adhesives - Determination of peel resistance of adhesive bonds - Floating roller method《粘合剂 粘结的抗剥离性测定 浮辊法［代替 CEN EN 1967］》.pdf》由会员分享，可在线阅读，更多相关《EN 1464-2010 en Adhesives - Determination of peel resistance of adhesive bonds - Floating roller method《粘合剂 粘结的抗剥离性测定 浮辊法［代替 CEN EN 1967］》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、BS EN 1464:2010ICS 83.180NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDAdhesives Determination of peelresistance of adhesivebonds Floating rollermethodThis British Standardwas published under theauthority of the StandardsPolicy and StrategyCommittee on 31 May2

2、010. BSI 2010ISBN 978 0 580 68328 2Amendments/corrigenda issued since publicationDate CommentsBS EN 1464:2010National forewordThis British Standard is the UK implementation of EN 1464:2010. Itsupersedes BS EN 1464:1995 and BS EN 1967:2002 which withdrawn.The UK participation in its preparation was e

3、ntrusted to TechnicalCommittee PRI/52, Adhesives.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisionsof a contract. Users are responsible for its correct application.Compliance with

4、a British Standard cannot confer immunityfrom legal obligations.areBS EN 1464:2010EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 1464 February 2010 ICS 83.180 Supersedes EN 1464:1994, EN 1967:2002English Version Adhesives - Determination of peel resistance of adhesive bonds - Floating roller m

5、ethod Adhsifs - Dtermination de la rsistance au pelage des assemblages - Mthode des galets mobiles Klebstoffe - Bestimmung des Schlwiderstandes von Klebungen - Rollenschlversuch This European Standard was approved by CEN on 28 December 2009. CEN members are bound to comply with the CEN/CENELEC Inter

6、nal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN memb

7、er. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN membe

8、rs are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,

9、Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2010 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Membe

10、rs. Ref. No. EN 1464:2010: EBS EN 1464:2010EN 1464:2010 (E) 2 Contents Page Foreword 31 Scope 42 Normative references 43 Terms and definitions .44 Apparatus .55 Test specimens 66 Conditioning and testing atmosphere .77 Procedure .77.1 Dry peel test .77.2 Wet peel test .88 Expression of results 89 Te

11、st report 8BS EN 1464:2010EN 1464:2010 (E) 3 Foreword This document (EN 1464:2010) has been prepared by Technical Committee CEN/TC 193 “Adhesives”, the secretariat of which is held by AENOR. This European Standard shall be given the status of a national standard, either by publication of an identica

12、l text or by endorsement, at the latest by August 2010, and conflicting national standards shall be withdrawn at the latest by August 2010. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held respo

13、nsible for identifying any or all such patent rights. This document supersedes EN 1464:1994 and EN 1967:2002. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EC Directive(s). Accor

14、ding to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Ita

15、ly, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. BS EN 1464:2010EN 1464:2010 (E) 4 1 Scope This European Standard specifies a floating roller method for the determination of the peel resis

16、tance of adhesive bonds between one rigid adherend and one flexible adherend when tested under specified conditions of preparation and testing. NOTE The use the floating roller produces more constant numerical data than other peel methods, but it should not be expected that the flexible adherend wil

17、l conform to the surface of the roller. SAFETY STATEMENT Persons using this document should be familiar with the normal laboratory practice, if applicable. This document does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user to e

18、stablish appropriate safety and health practices and to ensure compliance with any regulatory conditions. ENVIRONMENTAL STATEMENT It is understood that some of the material permitted in this standard may have negative environmental impact. As technological advantages lead to acceptable alternatives

19、for these materials, they will be eliminated from this standard to the extent possible. At the end of the test, the user of the standard should take care to carry out an appropriate disposal of the wastes, according to local regulation. 2 Normative references The following referenced documents are i

20、ndispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 923:2005, Adhesives Terms and definitions EN ISO 291, Plastics - Standard atmospheres

21、for conditioning and testing (ISO 291:2008) EN ISO 10365, Adhesives - Designation of main failure patterns (ISO 10365:1992) 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 923:2005 and the following apply. 3.1 peel resistance average force per unit te

22、st specimen width, measured along the bond line, required to separate progressively the two members of a bonded test specimen under specified conditions of test NOTE It is expressed in newtons per millimetre of width (N/mm). 3.2 wet-peel resistance peel resistance after application of water containi

23、ng a wetting agent BS EN 1464:2010EN 1464:2010 (E) 5 4 Apparatus 4.1 Tensile testing machine1), capable of maintaining a pre-determined constant crosshead rate to be reported in the test report (preferred rate: 100 mm/min). It shall be provided with a suitable self-aligning grip to hold the test spe

24、cimen. The jaws of this grip shall firmly engage the outer 25 mm of the end of the flexible adherend. The grip and attachments shall be so constructed that they will move into alignment with the test specimen as soon as the force is applied, so that the flexible member of the test specimen will coin

25、cide with the direction of the applied pull through the centre line of the grip assembly. The machine shall be autographic, giving a chart that can be read in terms of millimetres of crosshead movement as one coordinate and applied force as the other coordinate. All equipment shall be calibrated reg

26、ularly. It is recommended that equipment should be essentially free of inertial forces during use. The machine shall permit the measurement and recording of the applied force with an accuracy of 1 %. 4.2 Peel test fixture, for supporting the test specimen (see Figure 1). The fixture shall be attache

27、d to one of the cross-arms of testing machine (4.1). The 25 mm diameter rollers on the test fixture shall roll freely. The angle determined by the rollers and the use of dual roller bearings are critical and the rollers shall therefore be carefully maintained. 1) See for instance ISO 5893:2002, Rubb

28、er and plastics test equipment Tensile, flexural and compression types (constant rate of traverse) Specification. BS EN 1464:2010EN 1464:2010 (E) 6 Dimensions in millimetres Key 1 Rigid adherend 2 Peeling zone 3 Flexible adherend 4 Mild steel 5 Dual roller bearing type Figure 1 Peel test fixture for

29、 supporting test specimens 5 Test specimens 5.1 Test specimens of the dimensions shown in Figure 2 may be prepared individually or cut from bonded panels. Laminated test panels, or individual test specimens, shall consist of two adherends properly prepared and bonded together. 5.2 The adherends and

30、the surface treatment shall be in accordance with the intended application and process. The adhesive shall be applied in accordance with the manufacturers recommendations to obtain an optimum bond with minimum of variations. NOTE Direct comparison of different adhesives can be made only when test sp

31、ecimen construction, adherend materials and dimension and test conditions are identical. BS EN 1464:2010EN 1464:2010 (E) 7 5.3 The thickness of the flexible adherend shall be (0,5 0,02) mm and that of the rigid adherend shall be (2,5 0,1) mm in the case of metals, or thicker if other adherends are u

32、sed in order the reduce the deformation of the rigid adherend. 5.4 If the test specimens are cut from the bonded panels (see Figure 2) it shall not be deleterious to the bond. The width shall be either: a) 25 mm (the preferred width); or b) any other convenient width, provided that the test equipmen

33、t is suitably adapted and the width is stated in the test report. NOTE The method of cutting the test specimens is dependent upon the adherend and adhesive compositions. Milling and band-sawing are two methods commonly used for this purpose. 5.5 The unbounded end of the flexible adherend shall be be

34、nt perpendicular to the rigid adherend for clamping in the grip of the testing machine. 5.6 The number of specimens to be tested shall be as specified in the material specification or, if not so specified, shall be not less than five. Dimensions in millimetres Key a) angled b) not angled 1 direction

35、 of rolling s1thickness of the rigid adherend s2thickness of the flexible adherend Figure 2 Test specimen 6 Conditioning and testing atmosphere The test specimens shall be conditioned and tested in one of the standard laboratory atmospheres specified in EN ISO 291. 7 Procedure 7.1 Dry peel test Inse

36、rt the test specimen into the peel test fixture (4.2) as shown in Figure 1, with the unbounded end of the flexible adherend gripped in the jaw of the testing machine (4.1). Peel the specimen at a constant crosshead separation rate of (100 5) mm/min, unless otherwise specified. If the rigid adherend

37、bends or is distorted BS EN 1464:2010EN 1464:2010 (E) 8 during the test, it is recommended that the specimen be redesigned with a rigid adherend stiff enough to ensure even peeling. During the peel test, make an autographic recording of force versus crosshead movement (force versus distance peeled)

38、over a length of a least 115 mm of the bond line disregarding the first 25 mm of peel. Disregard the results if failure occurs outside the peeling zone as defined in Figure 1. 7.2 Wet peel test Insert the test specimen into the peel test fixture (4.2) as shown in Figure 1, with the unbounded end of

39、the flexible adherend gripped in the jaw of the testing machine (4.1). Peel the specimen at a constant crosshead separation rate of (100 5) mm/min, unless otherwise specified. If the rigid adherend bends or is distorted during the test, it is recommended that the specimen be redesigned with a rigid

40、adherend stiff enough to ensure even peeling. Stop the crosshead after peeling about 75 mm of the bonded length. Then apply several drops of water containing a wetting agent (for example 0,5 % to 1,0 % of a detergent) to the crack opening. After the application of this liquid the peeling process sha

41、ll be immediately commenced. The test shall be continued until the complete sample is peeled. An autographic recording of force versus crosshead movement (force versus distance peeled) shall be made. Disregard the results if failure occurs outside the peeling zone as defined in Figure 1. 8 Expressio

42、n of results Determine from the autographic curve, for at least 115 mm of peeling (disregarding the first 25 mm and the last 25 mm), the average peeling resistance, in newtons per millimetre (N/mm) of the test specimen width, required to separate the adherends. The average force may be determined fr

43、om the curve by one of the following methods: a) a planimeter; b) a gravimetric method, as follows: Cut out the area of the chard paper surrounded by the curve and the base line (abscissa) and weigh it. Determine the area by dividing its mass by the previously determine mass per surface area of the

44、chart paper. Divide the area thus found by the length of the base line (corresponding to 80 mm peeling length), to obtain the average height of the curve (and hence the average peeling force); c) by drawing the best straight line through the peeling curve using a straight edge; d) by any other metho

45、d such as computer assisted. Also record the maximum and minimum forces for each individual specimen. 9 Test report The test report shall include the following information: a) a reference to this European Standard; BS EN 1464:2010EN 1464:2010 (E) 9 b) identification of the adhesive tested, including

46、 type, source, manufacturers code number, batch or lot number, form, etc.; c) identification of adherends, including material, thickness, width and surface preparation; d) description of the bonding process, including method of application of adhesive, drying or pre-curing conditions (where applicab

47、le), and curing time, temperature and pressure; e) average thickness (as precisely as practicable) of the adhesive layer after formation of the bond; f) complete description of the test specimen, whether individual or panel, including dimensions and construction of the test specimen, conditions used

48、 for cutting individual test specimens, number of test panels represented and number of individual test specimens (when edge specimens are tested they shall be designated “edge specimens“); g) conditioning procedure prior to testing and the test conditions; h) if the crosshead separation rate is oth

49、er than 100 mm/min, the actual crosshead separation used; i) method of determining the average force; j) average, maximum and minimum peeling force values, in newtons per millimetre (N/mm) of test specimen width, for each individual specimen (edge samples shall be reported separately); k) type of failure according to EN ISO 10365. BS EN1464:2010BSI GroupHeadquarters 389Chiswick High Road,London, W4 4AL, UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 - British Standards Inst