EN 13473-3-2001 en Reinforcement - Specifications for Multi-Axial Multi-Ply Fabrics - Part 3 Specific Requirements《增强物 多轴多股纤维织物规范 第3部分 特殊要求》.pdf

《EN 13473-3-2001 en Reinforcement - Specifications for Multi-Axial Multi-Ply Fabrics - Part 3 Specific Requirements《增强物 多轴多股纤维织物规范 第3部分 特殊要求》.pdf》由会员分享，可在线阅读，更多相关《EN 13473-3-2001 en Reinforcement - Specifications for Multi-Axial Multi-Ply Fabrics - Part 3 Specific Requirements《增强物 多轴多股纤维织物规范 第3部分 特殊要求》.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD Reinforcement - Specifications for multi-axial mult i-ply fabrics - e Part 3: Specific requirements The European Standard 13473-3:2001 has the status of a British Standard ICs 59.100.99; 83.120 BS EN 13473-3:2001 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITED BY COPYRIGHT LAW

2、BS EN 13473-3:2001 Amd. No. National foreword Date Comments This British Standard is the official English language version of The UK participation in its preparation was entrusted to Technical Committee PRU42, Fibre reinforced thermosetting plastics and prepegs, which has the responsibility to: EN 1

3、3473-3:2001. - - aid enquirers to understand the text; present to the responsible European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. - This British

4、 Standard, having been prepared under the direction of the Sector Committee for Materials and Chemicals, was published under the authority of the Standards Committee and comes into effect on 15 August 2001 A list of organizations represented on this committee can be obtained on request to its secret

5、ary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled ?International Standards Correspondence Index?, or by using the ?Find facility of the BSI Standards E

6、lectronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages Thi

7、s document comprises a front cover, an inside front cover, the EN title page, pages 2 to 6, an inside back and a back cover. The BSI copyright date displayed in this document indicates when the document was last issued. Amendments issued since publication O BSI 07-2001 I I ISBN O 580 37758 X EUROPEA

8、N STANDARD NORME EUROPENNE EUROPISCHE NORM June 2001 ICs 59.100.99; 83.120 English version Reinforcement - Specifications for multi-axial multi-ply fabrics - Part 3: Specific requirements Renfort - Spcifications pour les tissus multi-axiaux multicouches - Partie 3: Exigences spcifiques Verstrkungen

9、- Spezifikation fr Multiaxialgelege - Teil 3: Besondere Anforderungen This European Standard was approved by CEN on 1 O May 2001. CEN members are bound to comply with the CENKENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standar

10、d without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other langua

11、ge made by translation under the responsibiliy of a CEN member into its own language and notified to the Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Icela

12、nd, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMITE EUROPEEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 E1050 Brussels 0 2001 CEN All rights of exploita

13、tion in any form and by any means resewed worldwide for CEN national Members. Ref. No. EN 13473-3:2001 E Page 2 EN 13473-3:2001 Contents Page Foreword 3 1 Scope 4 2 Normative references 4 3 Terms and definitions 4 4 Parameter specif cations 4 4.1 General 4 4.2 Parameters to be designated and control

14、led (group 1) . 4 4.3 Parameters to be designated but not controlled (group 2) . 5 4.4 Parameters not to be designated and not to be controlled (group 3) 5 5 Example 5 O . Page 3 EN 13473-3:2001 Foreword This European Standard has been prepared by Technical Committee CEN/TC 249 “Plastics“, the secre

15、tariat of which is held by IBN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by December 2001, and conflicting national standards shall be withdrawn at the latest by December 2001. This standard i

16、s one pari of EN 13473 “Reinforcement - Specifications for multi-axial multi-ply fabrics“ which is constructed as follows : - Part 1 : Designation - Part 2 : Methods of test and general requirements - - Part 3 : Specific requirements According to the CENKENELEC Internal Regulations, the national sta

17、ndards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. Page 4 EN

18、 13473-312001 1 Scope This Part 3 of EN 13473 is a specification of multi-axial multi-ply fabrics made from reinforcement yarns, tows, rovings, fibre fleeces, films, foams or other materials which are intended to provide reinforcement in composite materials and which is bound to a multi-ply construc

19、tion. This specification defines those parameters which are required for a particular application or processing method. The parameter specifications do not define absolute or nominal values for any parameter. The values for specified parameters are defined by the application. This specification defi

20、nes the test methods which shall be used to determine the values and tolerances for each specified parameter to be controlled by the textile manufacturer. The parameters which shall be defined in the technical specification of multi-axial multi-ply fabrics are defined in clause 4 of this Part. 2 Nor

21、mative references This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions o

22、f any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies (including amendments). EN 13473-1, Reinforcement - Specifications for multi-axial multi-ply fabrics - T

23、eil 7 : Designation EN 13473-2:2001, Reinforcement - Specifications for multi-axial multi-ply fabrics - Teil 2 : Methods of test and general requirements IS0 472, Plastics - Vocabulary IS0 3374, Reinforcement products - Mats and fabrics - Determination of mass per unit area IS0 5025, Reinforcement p

24、roducts - Woven fabrics - Determination of width and length 3 Terms and definitions For the purposes of this European Standard, the terms and definitions given in EN 13473-1, EN 13473-2 and IS0 472 apply. 4 Parameter specifications 4.1 General For each reinforcing multi-axial multi-ply fabric the no

25、minal values of the parameters shall be defined in accordance to the following division into three groups: The parameters and tolerances in group 1 shall be designated and controlled by the textile manufacturer. The parameters in group 2 shall be designated but not controlled by the textile manufact

26、urer. The parameters of group 3 neither have to be designated nor controlled by the textile manufacturer, but can be optionally agreed. 4.2 Parameters to be designated and controlled (group 1) Table 1 describes the test methods of the parameters which need to be designated and controlled. In additio

27、n the tolerances for the single parameter are defined. Parameters for special applications may differ from the tolerance values and have to be agreed. Page 5 EN 13473-32001 Parameter Total mass per unit area (multi-axial multi-ply fabric including binding system) Fabric width (on the roll) Fabric le

28、ngth (on the roll) Roll weight (net) Defects Test Method Tolerance IS0 3374 1.5% (see Note) IS0 5025 f 2% (minimum: - special handling/storage instructions ; - manufacturers production and traceability reference. 4.4 Parameters not to be designated and not to be controlled (group 3) Additional param

29、eters (e.9. filament diameter, sizing or finish, .) and other physical properties (see EN 13473-2:2001, 4.1, Table 1) are depending on the application. The tolerances and the values of these optional parameters and properties can be defined and agreed between the textile manufacturer and the custome

30、r. In case of any agreement, the additional parameters and properties have to be designated, too. 5 Example For the typical application in a windmill rotor blade the following example of a multi-axial multi-ply fabric is explained : - E-glass reinforcement yarn, filament diameter 17 pm, UP/EP compat

31、ible finish ; - 2 plies: -45“/+45“ ; - parallel weft ; - weight per 45O-ply: 300 g/m2 ; - loop system, PES, 8 gim2 ; - manufacturers code X ; - fabric width (on the roll): 1,26 m ; - fabric length (on the roll): 150 m ; o - defects - broken single yarn in loop system ( 300 mm), 3 per multi-axial mul

32、ti-ply fabric roll ; BS EN 1 34 7 3-3: 2 O0 1 BSI 389 Chiswick High Road London w4 4AL BSI - British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporat

33、ed by Royal Charter. Revisions c British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone

34、finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS

35、which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. Standards are also available from the BSI web

36、site at htto:/www.bsi-. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and

37、 international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of

38、 BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Further information about BSI is available on the BSI website

39、at httr,:/www.bsi-E. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retriev

40、al system or transmitted in any form or by any means - electronic, photocopying, recording or otherwise - without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designat

41、ions. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070.