EN 1312-1997 en Round and Sawn Timber - Determination of the Batch Volume of Sawn Timber《圆木材和板木材 板木材的批量体积测定》.pdf

《EN 1312-1997 en Round and Sawn Timber - Determination of the Batch Volume of Sawn Timber《圆木材和板木材 板木材的批量体积测定》.pdf》由会员分享，可在线阅读，更多相关《EN 1312-1997 en Round and Sawn Timber - Determination of the Batch Volume of Sawn Timber《圆木材和板木材 板木材的批量体积测定》.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD Round and sawn timber - Determination of the batch volume of sawn timber The European Standard EN 1312 : 1997 has the status of a British Standard ICs 79.040 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW BS EN 1312 : 1997 STD-BSI BS EN 1312-ENGL 1777 1b24bb9

2、 Ob392b3 380 Amd.No. Date BS EN 1312 : 1997 Text affected Committees responsible for this British Standard The preparation of this British Standard was entrusted by Technical Committee BM, Round and sawn timber, to Subcommittee B/543/2, Sawn timber, upon which the foowing bodies were represented Bri

3、tish Iimber Merchants Association British Woodworung Federation Department of the Environment (Building Research Establishment) Iimber Packaging and Pailet Confederation Iimber Research and Development Association Iimber li-ade Federation United Kingdom Softwood Sawmillers Association This British S

4、tandard, having been prepared under the direction of the Sector Board for Building and Civil Engineering, was published under the authority of the Standards Board and comes into effect on 15 September 1997 O BSI 1997 The following BSI references relate to the work on this standard Committee referenc

5、e B/543/2 Draft for comment 9Wl900 DC ISBN O 580 2746 5 I I I I STD-BSI BS EN L3LZ-ENGL 1977 Lb24bb9 Ob372bli 217 BS EN 1312 : 1997 Contents Committees responsible page Inside front cover National foreword ii Foreword 2 Text of EN 1312 3 O BSI 1997 1 STD*BSI BS EN L312-ENGL 1797 Lb24bbS Ob392b5 153

6、BS EN 1312 : 1997 National foreword This British Standard has been prepared by Subcommittee B/543E and is the English hguage version of EN 1312 : 1997 Round and sawn timber - Determination of Uze batch volume of sawn timber, published by the European Committee for Standardizhon (CEN). No existing Br

7、itish Standard is superseded. Cross-references Publication referred to Corresponding British Standard EN 844-3 EN 975-1 BS EN 844 Round and sawn timber - Tmimlogy Part 3 : 1995 Geneml temzs relating to sawn timber BS EN 975 Sawn timber- Appeumnce grading of hardwoods Part 1 : 1996 O - regularized gr

8、een timber, - regulanzed dried timber, - prepared timber, - planed imber, regardless of whether or not the timber meets the requirements of any dimensional or quaitative standards. 2 Normative references This European Standard incorporates, by dated or undated reference, provisions is the width, in

9、metres, to three decimal places; is the length, in metres, to three decimal places. Batches consisting of similar pieces are measured on the basis of the volume of a reference piece. If the volume of this piece is calculated as a separate operation, it shall be expressed in m3 to four decimal places

10、. The volume of a piece, measured separately, is expressed in m3 to three decimal places. 4.4 Calculation of the volume of a batch The volume of a batch shall be expressed in m3 to three decimal places. 4.4.1 Batches of timber, all pieces of the same size The volume is given by the formula: where V=

11、n x v, n V, is the number of pieces in the batch; is the volume of the reference piece. O BSI 1997 STD-BSI BS EN L3LZ-ENGL 1797 = Lb29bb Ob392b T9 m Page 4 EN 1312 : 1997 4.4.2 Batches of timber, all pieces of equal thickness and width but varying in length Measure the length of each piece individua

12、lly, in order to determine the total aggregate length of the batch. 4.4.3 Batches of timber, all pieces of equal thickness but varying in width and length The widths of equally long pieces are measured individuallx in order to determine their total aggregate width. The calculation may be based on th

13、e total width of a layer of planks, placed edge to edge. For each length, the volume is the aggregate width multiplied by the thickness and the length. 4.4.4 Batches of timber, with varying dimensions (thickness, length or width) It is recommended to split the batch into subbatches containing pieces

14、 of identical size, and then to proceed as above. 4.4.5 Volume of an unedged board, or a batch of separated unedged boards The volume is calculated takjng half the width of any wane into account, ignoring bark, halfway along the length of the board. In case of a feature at this point which would giv

15、e an incorrect result, two measurements are made equidistant from the mid-point and their mean is used. It is the supplier who measures. Sound sapwood is included in the measurement. 4.4.6 Volume of a boule l A A I C jn(/ / C Figure 1. Volume of a boule The total aggregate width is the basis of calc

16、ulation. This total aggregate width, or total width of the whole of the pieces in a boule, or of a series of successive pieces from any one boule, of equal length and thickness, is measured equidistant from the ends, perpendicular to the axis, ignoring bark. It is equal to the sum of the widths of t

17、he top faces of each unedged board. If the widths of the top faces of each unedged board are referred to as AA, BB, CC, DD, EE, , MM, then the developed width, Z b, is shown by the following formula: Z b =AA + BB + CC+ DD+EE+ . + MM 6 Reduction for defects and insect or fungal damage (separated uned

18、ged boards and boules) In accordance with the grade definitions laid down in EN 975-1, prEN 1611-1 and prEN 1611-2, volume reductions may be carried out where certain features or damage are present in the boards constituting the batch. One or more boards may not be withdrawn from a boule of a given

19、grade on the grounds that they contain a defect or that they are unsound. In such a case, volume reduction is carried out so as to take into account only the part which is: - sound, i.e. nondeteriorat Fax: 0181 996 7400. BSI offers members an individual updathg service called PLUS which ensures that

20、 subscribers automatidy receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services, Sales Department at Chiswick Tel 0181 996 7000; Fax: 0181 996 7001. In response to orders for internationa

21、l standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library, the Standardline

22、 Database, the BSI Information Technology Service (BlTS) and its Technical Help to Exporters Service. Contact the Infonnation Department at Chiswick Tel: 0181 996 7111; Fax: 0181 996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on

23、 the purchase price of standards. For details of these and other benefits contact Customer Services, Membership at Chiswick Tel 0181 996 7002; Fax: 0181 996 7001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international s

24、tandarmon bodies. Except as permitted under the Copynght, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or tsanSmitted in any form or by any means - electronic, photocopying, recording or otherwise - without prior written permission from BSI. This does not p

25、reclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be wed for any other purpose than implementation then the prior written permission of BSI must be obtained If permission is granted, the tem may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager, BSI, 389 Chiswick High Road, London W4 4AL