EN 12312-19-2005 en Aircraft ground support equipment - Specific requirements - Part 19 Aircraft jacks axle jacks and hydraulic tail stanchions (Incorporates Amendment A1 2009)《航空地.pdf

《EN 12312-19-2005 en Aircraft ground support equipment - Specific requirements - Part 19 Aircraft jacks axle jacks and hydraulic tail stanchions (Incorporates Amendment A1 2009)《航空地.pdf》由会员分享，可在线阅读，更多相关《EN 12312-19-2005 en Aircraft ground support equipment - Specific requirements - Part 19 Aircraft jacks axle jacks and hydraulic tail stanchions (Incorporates Amendment A1 2009)《航空地.pdf（20页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARDBS EN 12312-19:2005+A1:2009Aircraft ground support equipment Specificrequirements Part 19: Aircraft jacks, axle jacks and hydraulic tail stanchionsICS 49.100BS EN 12312-19:2005+A1:2009This British Standard waspublished under the authorityof the Standards Policy andStrategy Committee

2、on 6 July 2005 BSI 2009ISBN 978 0 580 61083 7National forewordThis British Standard is the UK implementation of EN 12312-19:2005+A1:2009.It supersedes BS EN 12312-19:2005, which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee ACE/57, Air cargo and ground sup

3、port equipment. A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisions of acontract. Users are responsible for its correct application.Compliance with a British Standard cannot confer

4、immunity fromlegal obligations.Amendments/corrigenda issued since publicationThe start and finish of text introduced or altered by amendment is indicated inthe text by tags. Tags indicating changes to CEN text carry the number of theCEN amendment. For example, text altered by CEN amendment A1 is ind

5、ic-ated by !“. Date Comments30 June 2009 Implementation of CEN amendment A1:2009EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 12312-19:2005+A1 April 2009 ICS 49.100 Supersedes EN 12312-19:2005English Version Aircraft ground support equipment - Specific requirements - Part 19: Aircraft jacks,

6、axle jacks and hydraulic tail stanchions Matriel au sol pour aronefs - Exigences particulires - Partie 19: Vrins de levage pour aronefs, vrins de changement de roues et monopoles hydrauliques Luftfahrt-Bodengerte - Besondere Anforderungen - Teil 19: Flugzeugheber, Radwechselheber und hydraulische He

7、cksttzen This European Standard was approved by CEN on 28 February 2005 and includes Amendment 1 approved by CEN on 1 March 2009. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standa

8、rd without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other l

9、anguage made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Fi

10、nland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES

11、 KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2009 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 12312-19:2005+A1:2009: EBS EN 12312-19:2005+A1:2009EN 12312-19:2005+A1:2009 (E) 2 Contents Page Foreword

12、3 1 Scope 52 Normative references 53 Terms and definitions . 64 List of hazards 65 Safety requirements and/or measures 66 Information for use 77 Verification of requirements . 8Annex A (informative) Typical examples of jacks and stanchions 9Annex B (normative) List of hazards in addition to those of

13、 EN 1915-1 11Annex C (normative) Manual forces and manual force measurement methods . 13Annex ZA (informative) Relationship between this European Standard and the Essential Requirements of EU Directive 98/37/EC, amended by Directive 98/79/EC 14Annex ZB (informative) !Relationship between this Europe

14、an Standard and the Essential Requirements of EU Directive 2006/42/EC“ . 15Bibliography 16BS EN 12312-19:2005+A1:2009EN 12312-19:2005+A1:2009 (E) 3 Foreword This document (EN 12312-19:2005+A1:2009) has been prepared by Technical Committee CEN/TC 274 “Aircraft ground support equipment“ the secretaria

15、t of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by October 2009, and conflicting national standards shall be withdrawn at the latest by December 2009. This document include

16、s Amendment 1, approved by CEN on 2009-03-01. This document supersedes EN 12312-19:2005. The start and finish of text introduced or altered by amendment is indicated in the text by tags ! “. This document has been prepared under a mandate given to CEN by the European Commission and the European Free

17、 Trade Association and supports essential requirements of EU Directive(s). !For relationship with EU Directives, see informative Annexes ZA and ZB, which are integral parts of this document.“ The Parts of EN 12312 Aircraft ground support equipment Specific requirements are: Part 1: Passenger stairs

18、Part 2: Catering vehicles Part 3: Conveyor belt vehicles Part 4: Passenger boarding bridges Part 5: Aircraft fuelling equipment Part 6: Deicers and deicing/antiicing equipment Part 7: Aircraft movement equipment Part 8: Maintenance stairs and platforms Part 9: Container/Pallet loaders Part 10: Conta

19、iner/Pallet transfer transporters Part 11: Container/Pallet dollies and loose load trailers Part 12: Potable water service equipment Part 13: Lavatory service equipment Part 14: Disabled/Incapacitated passenger boarding equipment Part 15: Baggage and equipment tractors Part 16: Air start equipment P

20、art 17: Air conditioning equipment Part 18: Nitrogen or Oxygen units Part 19: Aircraft jacks, axle jacks and hydraulic tail stanchions Part 20: Ground power equipment According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following coun-tries are bound to impl

21、ement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Den-mark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerlan

22、d and United Kingdom. BS EN 12312-19:2005+A1:2009EN 12312-19:2005+A1:2009 (E) 4 Introduction This document specifies health and safety requirements, as well as some functional and performance requirements for aircraft jacks, axle jacks and hydraulic tail stanchions intended to be used for servicing

23、and handling of all aircraft types commonly in service in civil air transport. The minimum essential criteria are considered to be of primary importance in providing safe, serviceable, economical, and practical aircraft jacks, axle jacks and tail stanchions. Deviations from the recommended criteria

24、should occur only after careful consideration, extensive testing, risk assessment and in service evaluation have shown alternative methods or conditions to be satisfactory. This document is a Type C standard as stated in !EN ISO 12100“. The machinery concerned and the extent to which hazards, hazard

25、ous situations and events are covered are indicated in the scope of this document. When provisions of this Type C standard are different from those which are stated in Type A or B standards, the provisions of this Type C standard take precedence over the provisions of the other standards, for machin

26、es that have been designed and built according to the provisions of this Type C standard. BS EN 12312-19:2005+A1:2009EN 12312-19:2005+A1:2009 (E) 5 1 Scope This document specifies the technical requirements to minimise the hazards listed in Clause 4 which can arise during the commissioning, operatio

27、n and maintenance of aircraft jacks, axle jacks and hydraulic tail stanchions when carried out in accordance with the specifications given by the manufacturer or his authorised representative. It also takes into account some performance requirements recognised as essential by authorities, aircraft a

28、nd ground support equipment (GSE) manufacturers as well as airlines and handling agencies. This document applies to: all types of aircraft jacks; axle jacks and hydraulic tail stanchions designed to be used at specific jacking points on the aircraft (examples see Annex A). NOTE A tail stanchion type

29、 is intended to be used with one type of aircraft. This document does not apply to aircraft recovery equipment. This document does not establish requirements for noise and vibration. Noise and vibration are dealt with respectively in EN 1915-4 and EN 1915-3. This Part of EN 12312 is not applicable t

30、o aircraft jacks, axle jacks and hydraulic tail stanchions which are manufactured before the date of publication of this document by CEN. !This part of EN 12312 is intended to be used in conjunction with EN 1915-1, EN 1915-2, EN 1915-3 (for vehicles) and EN 1915-4.“ 2 Normative references The follow

31、ing referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. !deleted text“ EN 1050:1996, Safety of machinery Principles

32、 for risk assessment EN 1915-1:2001, Aircraft ground support equipment General requirements Part 1: Basic safety requirements EN 1915-2, Aircraft ground support equipment General requirements Part 2: Stability and strength requirements, calculations and test methods !EN 1915-3, Aircraft ground suppo

33、rt equipment General requirements Part 3: Vibration measurement methods and reduction“ !EN 1915-4, Aircraft ground support equipment General requirements Part 4: Noise measurement methods and reduction“ EN ISO 12100-1:2003, Safety of machinery Basic concepts, general principles for design Part 1: Ba

34、sic termi-nology, methodology (ISO 12100-1:2003) EN ISO 12100-2:2003, Safety of machinery Basic concepts, general principles for design Part 2: Technical principles (ISO 12100-2:2003). !EN ISO 13850:2008, Safety of machinery Emergency stop Principles for design (ISO 13850:2006)“ BS EN 12312-19:2005+

35、A1:2009EN 12312-19:2005+A1:2009 (E) 6 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN ISO 12100:2003 and EN 1915-1:2001 and the following apply. 3.1 aircraft jack lifting device to support and/or raise an aircraft via its fuselage and wings 3.2 axle j

36、ack lifting device used to support and/or raise an aircraft via its axles 3.3 hydraulic tail stanchion device used to support an aircraft at its tail during loading and unloading operations 4 List of hazards The list of risks and hazards (see Annex B) is based on EN 1050 and contains the hazards and

37、 hazardous situa-tions, as far as they are dealt with in this document, identified by risk assessment as significant for aircraft jacks, axle jacks and hydraulic tail stanchions and which require action to eliminate or reduce risks. 5 Safety requirements and/or measures 5.1 General requirements 5.1.

38、1 !Aircraft jacks, axle jacks and hydraulic tail stanchions shall conform to the relevant requirements of EN 1915-1, EN 1915-2, EN 1915-3 and EN 1915-4 unless otherwise specified in this standard.“ They shall also conform to the specific requirements of this document. 5.1.2 Stability and strength ca

39、lculations shall be carried out in accordance with EN 1915-2. 5.1.3 Where a pressure relief valve is used for overload protection, it shall not be positioned between the ram and its control device. The pressure relief valve shall be adjusted to the lowest possible value but not exceeding 125 % of th

40、e rated load. 5.1.4 On jacks it shall be possible for the operator to control the lowering speed or stop the lowering at any load up to the rated load, e.g. on manually operated jacks, by a finely controllable valve. 5.1.5 Maximum admissible forces for manual operation and translation of jacks and s

41、tanchions and the methods to measure it are given in Annex C. 5.2 Specific requirements for aircraft jacks and hydraulic tail stanchions 5.2.1 Aircraft jacks and hydraulic tail stanchions shall be designed to enable safe and easy steering, e.g. one steering wheel out of three. 5.2.2 Permanent access

42、 shall be provided on aircraft jacks and hydraulic tail stanchions to enable positioning and adjustment of the upper load support point. Where this is only a ladder, the maximum distance between the fourth tread counting from the top of the ladder and the maximum extended position of the support poi

43、nt shall not exceed 2,0 m. 5.2.3 On power operated aircraft jacks and tail stanchions, emergency stops shall be installed at each operators panel. !They shall meet the requirements in EN ISO 13850:2008, Category 0 or 1.“ BS EN 12312-19:2005+A1:2009EN 12312-19:2005+A1:2009 (E) 7 5.2.4 Adjustable stab

44、ilisers may be considered as equivalent devices to fulfil the requirements in EN 1915-1:2001, 5.7.2. 5.2.5 The lifting system of aircraft jacks shall be equipped so that failure in the lifting device does not generate any hazardous movement of the lifting point/load. 5.2.6 Where more than one jack i

45、s intended to be used to lift an aircraft: failure of one drive shall induce stopping of all the jacks; monitoring of the movement shall be provided, in accordance with EN 1915-1:2001, 5.1; differences in height up to 100 mm shall be automatically corrected and differences in height of more than 100

46、 mm shall lead to immediate stop of all jacks; manual lowering shall not be used. The device to fulfil the requirements in EN 1915-1:2001, 5.20.3, shall be a pilot-operated check valve (see Clause 0 of EN 1915-1:2001 negotiation). 5.2.7 The upper load support point of hydraulic tail stanchions, when

47、 connected to the aircraft jacking point by the headstock, shall follow any upward movement of the aircraft tail. The foot of the stanchion shall not be lifted from the supporting surface. By receiving a load pressure defined by the aircraft manufacturer for the particular aircraft concerned, a safe

48、ty valve shall open and allow the cylinder to retract for downward movements of the aircraft tail. A pressure gauge, visible from the ground, shall be installed to indicate the pressure in the hydraulic system. 5.2.8 On hydraulic tail stanchions, the vertical forces shall be transmitted to the suppo

49、rting surface via the foot of the stanchion. The wheels shall not be used to transfer these forces. 5.2.9 Hydraulic tail stanchions shall allow all movement of the aircraft jacking point defined by the aircraft manu-facturer for the particular aircraft concerned without deflection. 5.3 Specific requirements for axle jacks 5.3.1 Axle jacks shall be designed to enable easy and accurate positioning , e.g. two steering wheels out of four. 5.3.2 Devices for towing shall be of rigid cons