EN 12132-2-1998 en Feather and down Methods of testing the down-proof properties of fabrics Part 2 Impact test (Incorporates Amendment A1 2003)《羽绒 纤维的连续密度的试验方法 第2部分 冲击试验 包含修改件A1-20.pdf

《EN 12132-2-1998 en Feather and down Methods of testing the down-proof properties of fabrics Part 2 Impact test (Incorporates Amendment A1 2003)《羽绒 纤维的连续密度的试验方法 第2部分 冲击试验 包含修改件A1-20.pdf》由会员分享，可在线阅读，更多相关《EN 12132-2-1998 en Feather and down Methods of testing the down-proof properties of fabrics Part 2 Impact test (Incorporates Amendment A1 2003)《羽绒 纤维的连续密度的试验方法 第2部分 冲击试验 包含修改件A1-20.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS EN 12132-2:1999 Incorporating Amendment No. 1 Feather and down Methods of testing the down-proof properties of fabrics Part 2: Impact test The European Standard EN 12132-2:1998 with the incorporation of amendment A1:2003, has the status of aBritish Standard ICS 59.040 BS EN 12132

2、-2:1999 This British Standard, having been prepared under the direction of the Sector Committee for Materials and Chemicals, was published under the authority of the Standards Committee and comes into effect on 15 January 1999 BSI 18 November 2003 ISBN 0 580 30430 2 National foreword This British St

3、andard is the official English language version of EN 12132-2:1998 including amendment A1:2003. The UK participation in its preparation was entrusted to Technical Committee TCI/73, Fillings and filled articles, which has the responsibility to: A list of organizations represented on this committee ca

4、n be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search”

5、facility of the BSI Electronic Catalogue or of British Standards Online. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obliga

6、tions. aid enquirers to understand the text; present to the responsible European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This do

7、cument comprises a front cover, an inside front cover, the EN title page, pages 2 to 6, an inside back cover and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. Date Comments 14532 18 November

8、 2003 Replacement of Table 1EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 12132-2 August 1998 + A1August 2003 ICS 59.040 Descriptors: stuffings, feathers, woven fabrics, tests, leak tests, impact tests, test conditions, procedure English version Feather and down Methods of testing the down-pr

9、oof properties of fabrics Part 2: Impact test (includes amendment A1:2003) Plumes et duvets Mthodes dessai des tissus pour ltanchit aux plumes et duvets Partie 2: Essai par impact (inclut lamendement A1:2003) Federn und Daunen Verfahren fr die Prfung der Daunendichtigkeit von Geweben Teil 2: Stoprfu

10、ng (enthlt nderung A1:2003) This European Standard was approved by CEN on 24 July 1998; amendment A1 was approved by CEN on 27 June 2003. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a nationa

11、l standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any o

12、ther language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany,

13、 Greece, Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and United Kingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Central Secretariat: rue de Stassart 36, B-10

14、50 Brussels 1998 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 12132-2:1998 + A1:2003 EEN 12132-2:1998 BSI 18 November 2003 2 Foreword This European Standard has been prepared by Technical Committee CEN/TC 222, Feather and down a

15、s filling material for any article, as well as finished articles filled with feather and down, the Secretariat of which is held by UNI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by February 199

16、9, and conflicting national standards shall be withdrawn at the latest by February 1999. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finlan

17、d, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. Foreword to amendment A1 This document (EN 12132-2:1998/A1:2003) has been prepared by Technical Committee CEN/TC 222, Feather and down as filling materia

18、l for any article, as well as finished articles filled with feather and down, the Secretariat of which is held by UNI This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by February 2004, and conflicting

19、 national standards shall be withdrawn at the latest by February 2004. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany

20、, Greece, Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and the United Kingdom.EN 12132-2:1998 BSI 18 November 2003 3 1 Scope This standard describes a method for the determination of down and feather penetration through the

21、primary tick fabric of a specimen containing feather and/or down filling, using an impact apparatus. 2 Normative references This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the tex

22、t and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references, the latest edition of the publication referred to appli

23、es. EN 20139, Textiles Standard atmospheres for conditioning and testing. (ISO 139:1973) EN 20187, Paper, board and pulps Standard atmosphere for conditioning and testing and procedure for monitoring the atmosphere and conditioning of samples. (ISO 187:1990) 3 Principle A cylindrical cushion is made

24、 from the fabric to be tested for its down-proof properties and is filled with a given amount of feather and down material or its mixtures. Sliding on an inclined plane, this cushion is moved by means of a pinned bar against a pinned plate, and is thus compressed. After the impact, the cushion is ro

25、lled back following the backward-moving pinned impact rake, and recovers its shape. This procedure is continuously repeated until a certain number of impacts is reached. As the stroke of the pinned plate is larger or smaller than the circumference of the cushion, the cushion will be compressed in di

26、fferent places. The number of down and/or feather particles which have passed or protruded from the primary tick fabric is counted. 4 Apparatus 4.1 Impact apparatus The testing apparatus (see Figure 1) consists of an inclined plane with an angle of inclination of 20 , used as a sliding face for the

27、cushion, and two perpendicular pinned plates. The lower plate, the impact rake S, is movable and can be moved back and forth by means of an eccentric drive. On this movable plate, three pins are firmly mounted 95 mm apart and offset to each other by an angle of 120 . The pins have the following dime

28、nsions: 80 mm long, 15 mm in diameter, with rounded front edges. The upper perpendicular pinned plate is firmly mounted and is used as the impact plate P. This plate has only one pin with the same dimensions as above, which is located at the centre, aligned between the three pins of the movable plat

29、e. The drive of the impact rake shall be designed so that the speed of the impact movement is twice that of the back movement (crank-rocker mechanism). The impact frequency shall be 35 impacts per minute. The stroke of the pinned impact rake S shall be designed so that the distance between the pins

30、of S and P is equal to or larger than 10 mm. The stroke shall be (500 5) mm. 4.2 Balance The balance shall be accurate to within 0,1 g. 5 Atmosphere for conditioning and testing Conditioning of test specimens and testing is carried out in an atmosphere according to EN 20139, and the temperature and

31、relative humidity are measured according to EN 20187. EN 12132-2:1998 4 BSI 18 November 2003 6 Preparation of test cushions At least two test specimens are taken from the fabric, each measuring 750 mm the whole width of fabric. One specimen is taken with its larger side in the warp direction, and on

32、e in the weft direction. From these specimens, two test cylindrical cushions shall be prepared. The surface area is (210 476) mm 2 . The cushion shall have a diameter of approximately (151,5 1) mm. The resulting effective cylindrical surface of the test cushion is 1 000 cm 2(see Figure 2, Figure 3 a

33、nd Figure 4). Fill the test specimen with the required mass of filling, based on composition according to Table 1. Table 1 Filling of the test cushion Down (%) Feathers (%) Mass of Filling (g) above70 below30 851 30to70 70to30 1101 10 to 30 90 to 70 130 1 below 10 above 90 150 1 Dimensions in millim

34、etres Key 1 Crank-rocker mechanism 2 Three movable pins 3 Cushion 4 Firmly mounted pin Figure 1 Impact test apparatus EN 12132-2:1998 BSI 18 November 2003 5 Dimensions in millimetres Key 1 Beginning or end of fabric 2 Fabric width Figure 2 Fabric sampling Dimensions in millimetres Key 1 Two round pi

35、eces 2 Surface area 3 Length seam 4 Bottom seam Figure 3 Fabric size and cut EN 12132-2:1998 6 BSI 18 November 2003 7 Procedure A different impact wear is applied for testing the down-proof properties: After each series of 500 impacts, the number of feathers and downs passed or protruding from the s

36、urface of the cushion cover is visually counted. Filling material which passed or is protruding from the circular ends or the seams is not taken into account. For the assessment of fabrics for their down-proof properties, the total number of passed or protruding and fallen feathers and down at the e

37、nd of the test is taken as a basis. 8 Test report The test report shall indicate the following particulars: reference to this European Standard; type of apparatus; description and designation of the tested fabric; description of the filling material and mass; impact wear; number of particles passed

38、or protruding from the fabric: a) cushion prepared with the surface area in warp direction; b) cushion prepared with the surface area in weft direction; any deviation from this European Standard and any incident likely to have affected the results. Dimensions in millimetres Figure 4 Cushion size for

39、 plain 1/1 fabrics: 2 000 impacts; for twill fabrics: 4 000 impacts; for satin 4/1 fabrics: 1 500 impacts (for quilts). blankBS EN 12132-2:1999 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards.

40、 It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant a

41、im of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44

42、 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed t

43、o Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as B

44、ritish Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give

45、 details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details

46、 of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-. Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- Further information about BSI is available o

47、n the BSI website at http:/www.bsi-. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, sto

48、red in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or gr

49、ade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-globa