EN 1123-2-2006 en Pipes and fittings of longitudinally welded hot-dip galvanized steel tube with spigot and socket for waste water systems - Part 2 Dimensions《废水系统用带龙头和插接套管的纵向焊接热浸镀.pdf

《EN 1123-2-2006 en Pipes and fittings of longitudinally welded hot-dip galvanized steel tube with spigot and socket for waste water systems - Part 2 Dimensions《废水系统用带龙头和插接套管的纵向焊接热浸镀.pdf》由会员分享，可在线阅读，更多相关《EN 1123-2-2006 en Pipes and fittings of longitudinally welded hot-dip galvanized steel tube with spigot and socket for waste water systems - Part 2 Dimensions《废水系统用带龙头和插接套管的纵向焊接热浸镀.pdf（68页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARDBS EN 1123-2:2006Pipes and fittings of longitudinally welded hot-dip galvanized steel tube with spigot and socket for waste water systems Part 2: DimensionsThe European Standard EN 1123-2:2006 has the status of a British StandardICS 23.040.10; 23.040.40; 23.040.60g49g50g3g38g50g51g60

2、g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58BS EN 1123-2:2006This British Standard was published under the authority of the Standards Policy and Strategy Committee

3、on 28 February 2007 BSI 2007ISBN 978 0 580 50227 9National forewordThis British Standard was published by BSI. It is the UK implementation of EN 1123-2:2006. It supersedes BS EN 1123-2:1999 which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee ISE/8, Steel p

4、ipes.A list of organizations represented on ISE/8 can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from lega

5、l obligations.Amendments issued since publicationAmd. No. Date CommentsEUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 1123-2November 2006ICS 23.040.10; 23.040.40; 23.040.60 Supersedes EN 1123-2:1999 English VersionPipes and fittings of longitudinally welded hot-dip galvanizedsteel tube with spigo

6、t and socket for waste water systems - Part2: DimensionsTubes et raccords, souds longitudinalement en aciergalvanis chaude, manchon enfichable pour rseauxdassainissement - Partie 2: DimensionsRohre und Formstcke aus lngsnahtgeschweitem,feuerverzinktem Stahlrohr mit Steckmuffe frAbwasserleitungen - T

7、eil 2: MaeThis European Standard was approved by CEN on 13 October 2006.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliograph

8、ical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN me

9、mber into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithu

10、ania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2006 CEN

11、All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 1123-2:2006: EEN 1123-2:2006 (E) 2 Contents Page Foreword4 Introduction .5 1 Scope 6 2 Normative references 6 3 Terms and definitions .6 4 Symbols and abbreviations 7 5 Dimensions.7 5.1 Gen

12、eral and tolerances .7 5.2 Sockets .9 5.3 Pipes .10 5.3.1 General10 5.3.2 Pipe with one socket Shape B 1 11 5.3.3 Pipe with two sockets Shape B 2 12 5.4 Bends 12 5.4.1 General12 5.4.2 Bend with large radius Shape C 1 .13 5.4.3 Bend with small radius Shape C 2.14 5.4.4 Bend with stilling section Shap

13、e C 3 15 5.4.5 Offset pipe Shape C 4 .16 5.5 Branches.17 5.5.1 General17 5.5.2 Single branch Shape D 1 17 5.5.3 Reducing single branch Shape D 11.19 5.5.4 Reducing double branch Shape D 21 .21 5.5.5 Reducing angular branch Shape D 31 23 5.5.6 Single transition branch Shape D 12 24 5.6 Connections .2

14、5 5.6.1 Genreal25 5.6.2 Connecting units for use with discharge sets of sanitary appliances.25 5.6.3 Connecting units for use with other kinds of pipes.33 5.7 Transition pipes .41 5.7.1 General41 5.7.2 Transition pipe (eccentric) Shape F 1 .41 5.7.3 Transition pipe (concentric) Shape F 2.42 5.7.4 Tr

15、ansition pipe (concentric) with extended spigot Shape F 343 5.7.5 Straight coupling Shape F 4.44 5.7.6 Insertion coupling with long socket Shape F 545 5.8 Traps .46 5.8.1 P-trap Shape G 1 .46 5.8.2 S-trap Shape G 2 .47 5.8.3 Pipe bridge (V-trap) Shape G 3 48 5.8.4 Rainpipe trap (type A) Shape G 4 49

16、 5.8.5 Rainpipe trap Shape G 5.50 5.9 Access pipes51 5.9.1 Access pipe with round cleaning hole Shape H 1 .51 5.9.2 Access pipe with rectangular cleaning hole Shape H 2 or with oval cleaning hole Shape H 352 5.10 Other fittings 52 EN 1123-2:2006 (E) 3 6 Accessories .53 6.1 Shear coupling.53 6.1.1 Sh

17、ear coupling A Shape K 153 6.1.2 Shear coupling B Shape K 253 6.1.3 Shear coupling with release Shape K 354 6.1.4 Shear coupling C Shape K 455 6.2 Plug.56 6.2.1 Plug Shape K 1056 6.2.2 Plug with extended spigot Shape K 11.57 6.2.3 Plug with screw top Shape K 1258 7 Seals .59 7.1 General .59 7.2 Seal

18、 for DN 40 to DN 200 Shape M 1.59 7.3 Seals Shape M 2 for DN 250 and DN 30060 7.4 Elastomeric pressure ring for DN 250 and DN 300 Shape M 3.61 7.5 Transition seal from steel pipe special socket to plastic discharge pipe Shape E 12 D.62 7.6 Gasket for round cleaning hole in access pipes of shape H 1

19、Shape H 1 D 63 7.7 Gasket for rectangular cleaning hole Shape H 2 D and gasket for oval cleaning hole Shape H 3 D64 EN 1123-2:2006 (E) 4 Foreword This document (EN 1123-2:2006) has been prepared by Technical Committee CEN/TC 165 “Waste water engineering”, the secretariat of which is held by DIN. Thi

20、s European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 2007, and conflicting national standards shall be withdrawn at the latest by May 2007. This document supersedes EN 1123-2:1999. This document on pi

21、pes and fittings of longitudinally welded hot-dip galvanized steel pipe with spigot and socket for waste water systems consists of the following Parts: Part 1: Requirements, testing, quality control; Part 2: Dimensions Part 3: Dimensions and special requirements for vacuum drainage systems and for d

22、rainage systems in shipbuilding According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Ice

23、land, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. EN 1123-2:2006 (E) 5 Introduction Pipes and fittings of longitudinally welded hot-dip galvanized steel pipes with spigot

24、and socket for waste water systems as specified in this European Standard are used in gravity drainage systems in buildings. For vacuum drainage systems and for drainage systems in shipbuilding, it was necessary to specify additional requirements and further dimensional specifications for components

25、 and joints used in these systems. Components specified in this EN 1123-3 are used for vacuum drainage systems and for drainage systems in shipbuilding. EN 1123-2:2006 (E) 6 1 Scope This European Standard applies to pipes and fittings of longitudinally welded hot-dip galvanized steel pipes with spig

26、ot and socket for waste water systems. It specifies dimensions and tolerances for pipes, fittings, pipe connectors and seals and establishes a system of designations for the different pipe and fitting types that conform to the stated requirements. This standard is only valid in connection with EN 11

27、23-1. This standard does not apply to the marking of products. EN 1123-1 applies to the marking. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest

28、edition of the referenced document (including any amendments) applies. EN 295 (all Parts), Vitrified clay pipes and fittings and pipe joints for drains and sewers EN 877, Cast iron pipes and fittings, their joints and accessories for the evacuation of water from buildings Requirements, test methods

29、and quality assurance EN 1123-1, Pipes and fittings of longitudinally welded hot-dip galvanized steel pipes with spigot and socket for waste water systems Part 1: Requirements, testing, quality control EN 1329-1, Plastics piping systems for soil and waste discharge (low and high temperature) within

30、the building structure Unplasticized poly(vinyl chloride) (PVC-U) Part 1: Specifications for pipes, fittings and the system EN 1451-1, Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure Polypropylene (PP) - Part 1: Specifications for pipes,

31、fittings and the system EN 1453-1, Plastics piping systems with structured-wall pipes for soil and waste discharge (low and high temperature) inside buildings Unplasticized poly(vinyl chloride) (PVC-U) Part 1: Specifications for pipes and the system EN 1455-1, Plastics piping systems for soil and wa

32、ste discharge (low and high temperature) within the building structure Acrylonitrile-butadiene-styrene (ABS) Part 1: Requirements for pipes, fittings and the system EN 1519-1, Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure Polyethylene (

33、PE) Part 1: Specifications for pipes, fittings and the system EN 1565-1, Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure Styrene copolymer blends (SAN+PVC) Part 1: Specifications for pipes, fittings and the system EN 1566-1, Plastics pipi

34、ng systems for soil and waste discharge (low and high temperature) within the building structure Chlorinated poly(vinyl chloride) (PVC-C) Part 1: Specifications for pipes, fittings and the system. 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 1123-1

35、:1999 apply. EN 1123-2:2006 (E) 7 4 Symbols and abbreviations DN/ID Nominal size with regard to the inside diameter DN/OD Nominal size with regard to the outside diameter d Diameter t Socket depth s Wall thickness l Effective length r Radius Angle t5 Least insertion depth e Off-set dimensions (shift

36、) 5 Dimensions 5.1 General and tolerances The dimensions given shall be followed. Where no dimensions are given in this European Standard, tolerances for linear dimensions shall be followed according to Table 1, tolerances for radii shall be followed according to Table 2, tolerances for angular dime

37、nsions referring to the smaller side length shall be followed according to Table 3 and tolerances for elastomer parts shall be followed according to Table 4. Table 1 Tolerances for linear dimensions Dimensions in millimetres Dimensional range Tolerance 0 to 300 5 more than 300 8 Table 2 Tolerances f

38、or radii Dimensions in millimetres Dimensional range Tolerance 26 to 181 3 181 to 378 4 378 to 457 5 EN 1123-2:2006 (E) 8 Table 3 Tolerances for materials, referring to the smaller side length Dimensions in millimetres Side length mm Tolerance 10 to 120 3 120 to 400 2 400 1,5 Table 4 Tolerances for

39、elastomer parts Dimensions in millimetres Tolerance Range of nominal size Form bound (F) % Form fitting bound (C) 25 to 40 0,6 1,0 40 to 63 0,8 1,3 63 to 100 1,0 1,6 100 to 160 1,3 2,0 160 0,8 by agreement with the manufacturer of the components EN 1123-2:2006 (E) 9 5.2 Sockets The socket dimensions

40、 according to Figure 1 shall conform to Table 5. Fittings are generally fabricated with socket type 1 A if the designation of the fitting does not specify the socket type. Dimensions not specified shall be chosen appropriately. Socket type 1 A Socket type 2 A/3 A Socket type 0,5 A Joint with ring se

41、al socket Standard socket Long socket Short socket1Figure 1 Socket types 1For use of the short socket, national regulations should be taken into account EN 1123-2:2006 (E) 10 Table 5 Socket dimensions Dimensions in millimetres Socket dimensions Nom- inal size DN/ID Type d1asbd2d3d4Tolerances for d1

42、to d4t1t2t3t4 min t5cTolerances for t1 tot440 42 1,5 0,15 45 48 45 0,6 30 70 100 16 20 42+50 53 1,5 0,15 56 60 56 0,6 38 90 130 19 28 42+70 73 1,6 0,16 76 81 76 0,7 55 120 175 27 35 42+80 A 89 1,6 0,16 92 99 92 0,9 60 130 190 31 40 42+80 B 89 1,8 0,18 92 99 92 0,9 60 130 190 31 40 42+100 102 2,0 0,2

43、0 106 114 107 1,0 70 150 220 38 45 42+125 133 2,5 0,25 138 147 140 1,3 75 160 235 41 50 42+150 159 2,5 0,25 164 176 168 1,6 80 170 250 46 55 42+200 219 3,0 0,35 224 241 228 2,2 120 250 370 76 85 42+250 A 273 3,0 0,36 280 298 284 2,7 130 270 400 90 100 53+250 B 273 4,0 0,45 280 298 284 2,7 130 270 40

44、0 90 100 53+300 A 324 3,0 0,36 331 350 336 3,2 130 270 400 90 100 53+300 B 324 4,0 0,45 331 350 336 3,2 130 270 400 90 100 53+aPipe ends slightly retracted. bThe wall thickness data refer to the ungalvanized pipe. cInstallation instructions only (necessary least insertion depth for tightness of conn

45、ection) except short socket. 5.3 Pipes 5.3.1 General The effective length of pipes shall comply with Table 6 or Table 7. If the pipes have an additional corrosion protection (P) according to EN 1123-1, this shall be added to the designation. EN 1123-2:2006 (E) 11 5.3.2 Pipe with one socket Shape B 1

46、 Type A (DN/ID 40 to DN/ID 200) Type B (DN/ID 250 and DN/ID 300) Figure 2 Shape B 1 Designation of a drainage steel pipe (B 1) with standard socket (1 A) of nominal size DN/ID 100 with an effective length l1= 1 000 mm Pipe EN 1123-2 B 1 1 A 100 1000 Table 6 Effective length of pipes (l1) Dimensions

47、in millimetres Nominal size DN/ID Effective length l1 5 40 50 70 80 100 125 150 200 250 500 750 1 000 1 500 2 000 3 000 4 000 250 300 500 750 1 000 1 500 2 000 3 000 4 000 EN 1123-2:2006 (E) 12 5.3.3 Pipe with two sockets Shape B 2 Figure 3 Shape B 2 Designation of a drainage steel pipe (B 2) with s

48、tandard socket (1 A) of nominal size DN/ID 100 and an effective length l7= 1 000 mm Pipe EN 1123-2 B 2 1A 100 1000 Table 7 Effective length of pipes (l7) Dimensions in millimetres Nominal size DN/ID Effective length l7 5 40 50 70 80 250 100 125 500 150 750 200 1 000 1 500 2 000 3 000 4 000 5.4 Bends

49、 5.4.1 General If required, type (A) or (B) and the additional corrosion protection (P) according to EN 1123-1 shall be added to the designation (see 5.3). EN 1123-2:2006 (E) 13 5.4.2 Bend with large radius Shape C 1 Figure 4 Shape C 1 Designation of a bend (C 1) of nominal size DN/ID 100 and = 45 of type (A): Bend EN 11