EN 10149-1-2013 en Hot rolled flat products made of high yield strength steels for cold forming - Part 1 General technical delivery conditions《冷成型用高屈服强度钢热轧扁平制品 第1部分 通用技术交货条件》.pdf

《EN 10149-1-2013 en Hot rolled flat products made of high yield strength steels for cold forming - Part 1 General technical delivery conditions《冷成型用高屈服强度钢热轧扁平制品 第1部分 通用技术交货条件》.pdf》由会员分享，可在线阅读，更多相关《EN 10149-1-2013 en Hot rolled flat products made of high yield strength steels for cold forming - Part 1 General technical delivery conditions《冷成型用高屈服强度钢热轧扁平制品 第1部分 通用技术交货条件》.pdf（20页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationBS EN 10149-1:2013Hot rolled flat products madeof high yield strength steels forcold formingPart 1: General technical delivery conditionsBS EN 10149-1:2013 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 10149-1:2013.It supersedes BS EN

2、10149-1:1996 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee ISE/103, Structural Steels Other Than Reinforcements.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to inclu

3、de all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2013. Published by BSI StandardsLimited 2013ISBN 978 0 580 73971 2ICS 77.140.50Compliance with a British Standard cannot confer immunity fromlegal obligations.This Britis

4、h Standard was published under the authority of theStandards Policy and Strategy Committee on 30 September 2013.Amendments issued since publicationDate Text affectedBS EN 10149-1:2013EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 10149-1 September 2013 ICS 77.140.50 Supersedes EN 10149-1:1995E

5、nglish Version Hot rolled flat products made of high yield strength steels for cold forming - Part 1: General technical delivery conditions Produits plats lamins chaud en aciers haute limite dlasticit pour formage froid - Partie 1: Conditions gnrales techniques de livraison Warmgewalzte Flacherzeugn

6、isse aus Sthlen mit hoher Streckgrenze zum Kaltumformen - Teil 1: Allgemeine technische Lieferbedingungen This European Standard was approved by CEN on 17 August 2013. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European St

7、andard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (Engl

8、ish, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium,

9、Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland

10、, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2013 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Memb

11、ers. Ref. No. EN 10149-1:2013: EBS EN 10149-1:2013EN 10149-1:2013 (E) 2 Contents Page Foreword . 3 1 Scope 4 2 Normative references . 4 3 Terms and definitions 5 4 Information to be supplied by the purchaser 6 4.1 Mandatory information . 6 4.2 Options . 6 5 Dimensions, mass and tolerances 6 5.1 Dime

12、nsions and tolerances . 6 5.2 Mass of steel 6 6 Classification and designation 6 6.1 Classification and grades 6 6.2 Designation 6 7 Technical requirements . 7 7.1 Steel manufacturing process . 7 7.2 Delivery condition 7 7.3 Chemical composition . 8 7.4 Mechanical properties 9 7.5 Technological prop

13、erties . 9 7.6 Surface finish . 10 7.7 Internal soundness 10 8 Inspection and testing . 11 8.1 General . 11 8.2 Sampling . 11 8.3 Test units 11 8.4 Verification of chemical composition 11 8.5 Preparation of samples and test pieces 11 8.6 Test methods 12 8.7 Retests and resubmission for testing . 13

14、8.8 Inspection documents . 13 9 Marking . 14 10 Disputes 14 11 Options . 14 Bibliography 16 BS EN 10149-1:2013EN 10149-1:2013 (E) 3 Foreword This document (EN 10149-1:2013) has been prepared by Technical Committee ECISS/TC 103 “Structural steel other than reinforcements”, the secretariat of which is

15、 held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by March 2014, and conflicting national standards shall be withdrawn at the latest by March 2014. Attention is drawn to the possibility t

16、hat some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 10149-1:1995. In comparison with EN 10149-1:1995, the following significant technical changes wer

17、e made: definition 3.2, Note 1 modified; subclause 7.4.1.1, Note modified and changed to standard text; subclause 7.5.1, Note 2 for welding suitability of grades S900MC and S960MC added; Table 1, values for Mn, Ti and Mo modified. The specific requirements for hot rolled products made of high yield

18、strength steels for cold forming are given in the EN 10149-2 and EN 10149-3. The titles of the other Parts of this European Standard are: Part 2: Technical delivery conditions for thermomechanical rolled steels; Part 3: Technical delivery conditions for normalized or normalized rolled steels. Accord

19、ing to the CEN-CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany,

20、Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 10149-1:2013EN 10149-1:2013 (E) 4 1 Scope 1.1 This European Standard specifies requirem

21、ents for flat products made of weldable, hot-rolled, high yield strength alloy quality and special steels for cold forming. EN 10149-1 specifies the general delivery conditions. EN 10149-2 specifies the delivery conditions for thermomechanically rolled steels in the grades given in Table 1 (chemical

22、 composition) and Table 2 (mechanical properties) of Part 2. EN 10149-3 specifies the delivery conditions for normalised or normalised rolled steels in the grades given in Table 1 (chemical composition) and Table 2 (mechanical properties) of Part 3. 1.2 This European Standard does not apply to produ

23、cts for pressure vessels and products for which other European Standards exist or European Standards dealing with steels for general structural applications are being prepared: Hot-rolled products of structural steels (see EN 10025 parts 1 to 6); Hot finished structural hollow sections of non-alloy

24、and fine grain steels (see EN 10210-1). 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the

25、referenced document (including any amendments) applies. EN 10020, Definition and classification of grades of steel EN 10021, General technical delivery conditions for steel products EN 10029, Hot-rolled steel plates 3 mm thick or above - Tolerances on dimensions and shape EN 10048, Hot-rolled narrow

26、 steel strip Tolerances on dimensions and shape EN 10051, Continuously hot-rolled strip and plate/sheet cut from wide strip of non-alloy and alloy steels Tolerances on dimensions and shape EN 10052:1993, Vocabulary of heat treatment terms for ferrous products EN 10079:2007, Definition of steel produ

27、cts EN 10149-2:2013, Hot rolled flat products made of high yield strength steels for cold forming Part 2: Technical delivery conditions for thermomechanically rolled steels EN 10149-3:2013, Hot rolled flat products made of high yield strength steels for cold forming Part 3: Technical delivery condit

28、ions for normalized or normalized rolled steels EN 10160, Ultrasonic testing of steel flat product of thickness equal to or greater than 6 mm (reflection method) EN 10162, Cold-rolled steel sections Technical delivery conditions Dimensional and cross-sectional tolerances BS EN 10149-1:2013EN 10149-1

29、:2013 (E) 5 EN 10163-1, Delivery requirements for surface condition of hot-rolled steel plates, wide flats and sections Part 1: General requirements EN 10163-2, Delivery requirements for surface condition of hot-rolled steel plates, wide flats and sections Part 2: Plate and wide flats EN 10168, Stee

30、l products Inspection documents List of information and description EN 10204, Metallic products Types of inspection documents EN ISO 148-1, Metallic materials Charpy pendulum impact test Part 1: Test method (ISO 148-1) EN ISO 377, Steel and steel products Location and preparation of samples and test

31、 pieces for mechanical testing (ISO 377) EN ISO 2566-1, Steel Conversion of elongation values Part 1: Carbon and low alloy steels (ISO 2566-1) EN ISO 6892-1:2009, Metallic materials Tensile testing Part 1: Method of test at room temperature (ISO 6892-1:2009) EN ISO 7438, Metallic materials Bend test

32、 (ISO 7438) 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 10052:1993, EN 10079:2007 and the following apply. 3.1 fine grained steels steels with fine grain structure with an equivalent index of ferritic grain size 6 Note 1 to entry: For the determin

33、ation of grain sizes, see EN ISO 643. 3.2 thermomechanical rolling rolling process in which the final deformation is carried out in a certain temperature range leading to a material condition with certain properties which cannot be achieved or repeated by heat treatment alone Note 1 to entry: Hot fo

34、rming or post weld heat treatment at a temperature above 580 C may lower the strength values and for this reason is better not performed. Flame straightening can be applied in accordance with CEN/TR 10347. For grades S900MC and S960MC, subsequent heating at temperature above 400 C is not recommended

35、. Note 2 to entry: Thermomechanical rolling can include processes with an increasing cooling rate with or without tempering including self-tempering but excluding direct quenching and quenching and tempering. Note 3 to entry: In some publications, the word TMCP (Thermomechanical Control Process) is

36、also used. 3.3 normalised rolled rolling process in which the final deformation is carried out in a certain temperature range leading to a material condition equivalent to that obtained after normalising so that the specified values of the mechanical properties are retained even after normalising No

37、te 1 to entry: In international publications for both the normalising rolling, as well as the thermomechanical rolling, the expression “controlled rolling“ may be found. However, in view of the different applicability of the products, a distinction of the terms is necessary. BS EN 10149-1:2013EN 101

38、49-1:2013 (E) 6 4 Information to be supplied by the purchaser 4.1 Mandatory information The following information shall be supplied by the purchaser at the time of the order: a) details of the product form and quantity; b) reference to this European Standard; c) nominal dimensions and tolerances (se

39、e 5.1); d) the grade and delivery condition of the steel (see EN 10149-2 and EN 10149-3); e) type of inspection document (see 8.8). 4.2 Options A number of options are specified in Clause 11. In the event that the purchaser does not indicate his wish to implement any of these options, the supplier s

40、hall supply in accordance with the basic specification. 5 Dimensions, mass and tolerances 5.1 Dimensions and tolerances Dimensions and tolerances shall be in accordance with EN 10029, EN 10048 or EN 10051. 5.2 Mass of steel The calculated mass shall be determined using a volumetric mass of 7,85 kg/d

41、m3. 6 Classification and designation 6.1 Classification and grades Classification shall be in accordance with EN 10149-2 and EN 10149-3 which specify steel grades that are alloy quality steels or alloy special steels according to EN 10020. The steels for flat products specified in EN 10149-2 and EN

42、10149-3 are subdivided into grades on the basis of the minimum specified yield strength at ambient temperature. 6.2 Designation 6.2.1 Steel names and steel numbers For the steel grades covered by this European Standard, the steel names are allocated in accordance with EN 10027-1; the steel numbers a

43、re allocated in accordance with EN 10027-2. BS EN 10149-1:2013EN 10149-1:2013 (E) 7 6.2.2 Details for the designation The designation shall consist of: the number of this European Standard (EN 10149-2 or EN 10149-3); the steel number or the steel name consisting of: the symbol S (for structural stee

44、l); the indication of the minimum specified yield strength expressed in MPa1); the symbol for the delivery condition (M or N) (see EN 10149-2 and EN 10149-3); the capital letter C indicating the steel is suitable for cold forming (see EN 10149-2 and EN 10149-3). EXAMPLE 1 Thermomechanically rolled (

45、M) structural steels (S) with a specified minimum yield strength at room temperature of 420 MPa1)(420) suitable for cold forming (C): Steel EN 10149-2 - 1.0980 or Steel EN 10149-2 - S420MC EXAMPLE 2 Structural steels (S) with a specified minimum yield strength at room temperature of 420 MPa1) (420)

46、in the normalised or normalised rolled condition (N) suitable for cold forming (C): Steel EN 10149-3 - 1.0981 or Steel EN 10149-3 - S420NC 7 Technical requirements 7.1 Steel manufacturing process 7.1.1 The steel manufacturing process shall be at the manufacturers option. If specified at the time of

47、the order, the steel manufacturing process shall be reported to the purchaser. See Clause 11, option 1). 7.1.2 The steels specified in this European Standard shall be fully killed. The steels shall have a fine grain structure containing nitrogen binding elements in amounts sufficient to bind the ava

48、ilable nitrogen. 7.2 Delivery condition 7.2.1 Thermomechanically rolled steel The products described in EN 10149-2 are obtained by thermomechanical rolling. 1) 1 MPa = 1 N/mm2. BS EN 10149-1:2013EN 10149-1:2013 (E) 8 7.2.2 Normalised or normalised rolled steel The products described in EN 10149-3 ar

49、e delivered in the normalised or normalised rolled condition. 7.2.3 Surface protection Unless otherwise agreed at the time of the order, the products are generally supplied with their surfaces in untreated condition. If agreed at the time of the order, the products may be delivered with descaled surfaces. However, it is necessary to take into account the fact that certain descaling processes are liable to modify the cold forming properties. See Clause 11, option 2). The descaled continuous rolled prod