ECA EIA-60384-25-1-2014 Fixed Capacitors for Use in Electronic Equipment C Part 25-1 Blank Detail Specification C Surface Mount Fixed Aluminium Electrolytic Capacitors with Conduct.pdf

《ECA EIA-60384-25-1-2014 Fixed Capacitors for Use in Electronic Equipment C Part 25-1 Blank Detail Specification C Surface Mount Fixed Aluminium Electrolytic Capacitors with Conduct.pdf》由会员分享，可在线阅读，更多相关《ECA EIA-60384-25-1-2014 Fixed Capacitors for Use in Electronic Equipment C Part 25-1 Blank Detail Specification C Surface Mount Fixed Aluminium Electrolytic Capacitors with Conduct.pdf（19页珍藏版）》请在麦多课文档分享上搜索。

1、 EIA STANDARD Fixed Capacitors for Use in Electronic Equipment Part 25-1: Blank Detail Specification Surface Mount Fixed Aluminium Electrolytic Capacitors with Conductive Polymer Solid Electrolyte Assessment Level EZ EIA-60384-25-1 (IEC 60384-25-1:2006, IDT) September 2014 ANSI/EIA-60384-25-1-2014 A

2、pproved: September 30, 2014 EIA-60384-25-1NOTICE EIA Engineering Standards and Publications are designed to serve the public interest through eliminating misunderstandings between manufacturers and purchasers, facilitating interchangeability and improvement of products, and assisting the purchaser i

3、n selecting and obtaining with minimum delay the proper product for his particular need. Existence of such Standards and Publications shall not in any respect preclude any member or nonmember of ECIA from manufacturing or selling products not conforming to such Standards and Publications, nor shall

4、the existence of such Standards and Publications preclude their voluntary use by those other than ECIA members, whether the standard is to be used either domestically or internationally. Standards and Publications are adopted by ECIA in accordance with the American National Standards Institute (ANSI

5、) patent policy. By such action, ECIA does not assume any liability to any patent owner, nor does it assume any obligation whatever to parties adopting the Standard or Publication. This EIA Standard is identical (IDT) with the International Standard IEC Publication 60384-25-1:2006: Fixed Capacitors

6、for Use in Electronic Equipment Part 25-1: Blank Detail Specification Surface Mount Fixed Aluminium Electrolytic Capacitors with Conductive Polymer Solid Electrolyte Assessment Level EZ. This document is the EIA Standard EIA-60384-25-1 2014 Edition 1: Fixed Capacitors for Use in Electronic Equipment

7、 Part 25-1: Blank Detail Specification Surface Mount Fixed Aluminium Electrolytic Capacitors with Conductive Polymer Solid Electrolyte Assessment Level EZ. The text, figures and tables of IEC 60384-25-1:2006 are used in this Standard with the consent of the IEC and the American National Standards In

8、stitute (ANSI). The IEC copyrighted material has been reproduced with permission from ANSI. The IEC Foreword and Introduction are not part of the requirements of this standard but are included for information purposes only. This Standard does not purport to address all safety problems associated wit

9、h its use or all applicable regulatory requirements. It is the responsibility of the user of this Standard to establish appropriate safety and health practices and to determine the applicability of regulatory limitations before its use. (From Standards Proposal No. 5268, formulated under the cogniza

10、nce of the P-2.5 Committee on EIA Solid Electrolytic Capacitors Standards and given final approval by the Standards Steering Committee for Passive Electronic Components Standards (S-1). Published by Electronic Components Industry Association 2014 Engineering Department 2214 Rock Hill Road, Suite 265

11、 Herndon, VA 20170 PLEASE! DONT VIOLATE THE LAW! This document is copyrighted by the ECIA and may not be reproduced without permission. Organizations may obtain permission to reproduce a limited number of copies through entering into a license agreement. For information, contact: IHS 15 Inverness Wa

12、y East Englewood, CO 80112-5704 or call USA and Canada (1-877-413-5184), International (303-397-7956) i Contents FOREWORD 1 Blank detail specification . 4 1 General data 5 1.1 Recommended method(s) of mounting (to be inserted) 5 1.2 Dimensions . 5 1.3 Ratings and characteristics 6 1.4 Normative refe

13、rences . 7 1.5 Marking . 7 1.6 Ordering information 7 1.7 Certified records of released lots 7 1.8 Additional information (not for inspection purposes) . 7 1.9 Additional or increased severities or requirements to those specified in the generic and/or sectional specification . 7 2 Inspection require

14、ments 7 2.1 Procedures 7 Table 1 Case size reference and dimensions . 5 Table 2 Values of capacitance and of voltage related to case sizes 6 Table 3 Values of rated ripple current, equivalent series resistance, tangent of loss angle and leakage current . 6 Table 4 Values of resistance to soldering h

15、eat, damp heat, steady state and characteristics at high temperature 6 Table 5 Other characteristics 7 Table 6 Test schedule for quality conformance inspection 8 EIA-60384-25-1 Page 1 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ FIXED CAPACITORS FOR USE IN ELECTRONIC EQUIPMENT Part 25-1: Blank detail

16、 specification Surface mount fixed aluminium electrolytic capacitors with conductive polymer solid electrolyte Assessment level EZ FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC

17、National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, P

18、ublicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-gov

19、ernmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC

20、 on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accep

21、ted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote internation

22、al uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the lat

23、ter. 5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any equipment declared to be in conformity with an IEC Publication. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its d

24、irectors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses ari

25、sing out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is

26、 drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 60384-25-1 has been prepared by IEC technical committee 40: Capacitors and resi

27、stors for electronic equipment. The text of this standard is based on the following documents: FDIS Report on voting 40/1734/FDIS 40/1757/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. This publication has been

28、drafted in accordance with the ISO/IEC Directives, Part 2. EIA-60384-25-1 Page 2 IEC 60384 consists of the following parts, under the general title Fixed capacitors for use in electronic equipment: Part 1: Generic specification Part 2: Sectional specification: Fixed metallized polyethylene-terephtha

29、late film dielectric d.c. capacitors Part 3: Sectional specification: Fixed tantalum chip capacitors Part 4: Sectional specification: Aluminium electrolytic capacitors with solid and non-solid electrolyte Part 5: Sectional specification: Fixed mica dielectric d.c. capacitors with a rated voltage not

30、 exceeding 3 000 V Selection of methods of test and general requirements Part 6: Sectional specification: Fixed metallized polycarbonate film dielectric d.c. capacitors Part 7: Sectional specification: Fixed polystyrene film dielectric metal foil d.c. capacitors Part 8: Sectional specification: Fixe

31、d capacitors of ceramic dielectric, Class 1 Part 9: Sectional specification: Fixed capacitors of ceramic dielectric, Class 2 Part 11: Sectional specification: Fixed polyethylene-terephthalate film dielectric metal foil d.c. capacitors Part 12: Sectional specification: Fixed polycarbonate film dielec

32、tric metal foil d.c. capacitors Part 13: Sectional specification: Fixed polypropylene film dielectric metal foil d.c. capacitors Part 14: Sectional specification: Fixed capacitors for electromagnetic interference suppression and connection to the supply mains Part 15: Sectional specification: Fixed

33、tantalum capacitors with non-solid or solid electrolyte Part 16: Sectional specification: Fixed metallized polypropylene film dielectric d.c. capacitors Part 17: Sectional specification: Fixed metallized polypropylene film dielectric a.c. and pulse capacitors Part 18: Sectional specification: Fixed

34、aluminium electrolytic chip capacitors with solid and non-solid electrolyte Part 19: Sectional specification: Fixed metallized polyethylene-terephthalate film dielectric chip d.c. capacitors Part 20: Sectional specification: Fixed metallized polyphenylene sulphide film dielectric chip d.c. capacitor

35、s Part 21: Sectional specification: Fixed surface mount multilayer capacitors of ceramic dielectric, Class 1 Part 22: Sectional specification: Fixed surface mount multilayer capacitors of ceramic dielectric, Class 2 Part 23: Sectional specification: Fixed surface mount metallized polyethylene naphth

36、alate film dielectric d.c. capacitors Part 24: Sectional specification: Surface mount fixed tantalum electrolytic capacitors with conductive polymer solid electrolyte Part 25: Sectional specification: Surface mount fixed aluminium electrolyte capacitors with conductive polymer solid electrolyte All

37、sectional specifications mentioned above do have one or more blank detail specifications being a supplementary document, containing requirements for style, layout and minimum content of detail specifications. EIA-60384-25-1 Page 3 The committee has decided that the contents of this publication will

38、remain unchanged until the maintenance result date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. A bilingual version of this publica

39、tion may be issued at a later date. EIA-60384-25-1 Page 4 FIXED CAPACITORS FOR USE IN ELECTRONIC EQUIPMENT Part 25-1: Blank detail specification Surface mount fixed aluminium electrolytic capacitors with conductive polymer solid electrolyte Assessment level EZ Blank detail specification A blank deta

40、il specification is a supplementary document to the sectional specification and contains requirements for style, layout and minimum content of detail specifications. Detail specifications not complying with these requirements may not be considered as being in accordance with IEC specifications nor s

41、hall they so be described. In the preparation of detail specifications the content of 1.4 of the sectional specification shall be taken into account. The numbers between square brackets on the first page of the detail specification correspond to the following information, which shall be inserted in

42、the position indicated. Identification of the detail specification 1 The “International Electrotechnical Commission“ or the National Standards Organization under whose authority the detail specification is drafted. 2 The IEC or National Standards number of the detail specification, date of issue and

43、 any further information required by the national system. 3 The number and issue number of the IEC or national generic specification. 4 The IEC number of the blank detail specification. Identification of the capacitor 5 A short description of the type of capacitor. 6 Information on typical construct

44、ion (when applicable). 7 Outline drawing with main dimensions which are of importance for interchangeability and/or reference to the national or international documents for outlines. Alternatively, this drawing may be given in an annex to the detail specification. 8 Application or group of applicati

45、ons covered and/or assessment level. 9 Reference data on the most important properties, to allow comparison between the various capacitor types. EIA-60384-25-1 Page 5 1 2 ELECTRONIC COMPONENTS OF ASSESSED QUALITY IN ACCORDANCE WITH: 3 IEC 60384-25-1 4 Surface mount fixed aluminium electrolytic capac

46、itors with conductive polymer solid electrolyte 5 Outline drawing : (see Table 1) (angle projection) 7 6Assessment level(s): EZ 8 Information on the availability of components qualified to this detail specification is given in EC QC 001005. 9 1 General data 1.1 Recommended method(s) of mounting (to

47、be inserted) (See 1.4.2 of IEC 60384-25). 1.2 Dimensions Table 1 Case size reference and dimensions Case size reference Dimension mm L W H NOTE 1 When there is no case size reference, Table 1 may be omitted and the dimensions should be given in Table 2, which then becomes Table 1. NOTE 2 The dimensi

48、ons should be given as maximum dimensions or as nominal dimensions with a tolerance.NOTE 3 L, W, H of the symbols of Table 1 is the example of the corner shape capacitors. EIA-60384-25-1 Page 6 1.3 Ratings and characteristics Rated capacitance range (see Table 2) Tolerance on rated capacitance Rated

49、 voltage (see Table 2) Surge voltage (see Table 2) Climatic category Rated temperature Rated ripple current (see Table 3) Tangent of loss angle (see Table 3) Leakage current (see Table 3) Equivalent series resistance (see Table 3) Table 2 Values of capacitance and of voltage related to case sizes Rated voltage V Surge voltage V Rated capacitance F Case sizes Case sizes Case sizes Case sizes Table 3 Values of rated ripple current, equivalent series resistance, tangent of loss angle an