ECA EIA-364-08C-2015 TP-08C Crimp Tensile Strength Test Procedure for Electrical Connectors.pdf

《ECA EIA-364-08C-2015 TP-08C Crimp Tensile Strength Test Procedure for Electrical Connectors.pdf》由会员分享，可在线阅读，更多相关《ECA EIA-364-08C-2015 TP-08C Crimp Tensile Strength Test Procedure for Electrical Connectors.pdf（11页珍藏版）》请在麦多课文档分享上搜索。

1、 EIA STANDARD TP-08C Crimp Tensile Strength Test Procedure for Electrical Connectors EIA-364-08C (Revision of EIA-364-08B) August 2015 Electronic Components Industry Association EIA-364-08C ANSI/EIA-364-08C-2015 Approved: August 26, 2015 NOTICE EIA Engineering Standards and Publications are designed

2、 to serve the public interest through eliminating misunderstandings between manufacturers and purchasers, facilitating interchangeability and improvement of products, and assisting the purchaser in selecting and obtaining with minimum delay the proper product for his particular need. Existence of su

3、ch Standards and Publications shall not in any respect preclude any member or nonmember of ECIA from manufacturing or selling products not conforming to such Standards and Publications, nor shall the existence of such Standards and Publications preclude their voluntary use by those other than ECIA m

4、embers, whether the standard is to be used either domestically or internationally. Standards and Publications are adopted by ECIA in accordance with the American National Standards Institute (ANSI) patent policy. By such action, ECIA does not assume any liability to any patent owner, nor does it ass

5、ume any obligation whatever to parties adopting the Standard or Publication. This standard is based upon the major technical content of International Electrotechnical Commission standard 60512-16-4 (was IEC 512-8, test 16d), tensile strength (crimped connections), 2008-06, first edition. It conforms

6、 in all essential respects this IEC standard. This Standard does not purport to address all safety problems associated with its use or all applicable regulatory requirements. It is the responsibility of the user of this Standard to establish appropriate safety and health practices and to determine t

7、he applicability of regulatory limitations before its use. (From Standards Proposal No. 5345.04 formulated under the cognizance of the CE-2.0 Committee on EIA National Connector and Sockets Standards.) Published by Electronic Components Industry Association 2015 EIA Standards see 4.4 6.7 Name of ope

8、rator and start/finish dates of test ECIA Document Improvement Proposal If in the review or use of this document, a potential change is made evident for safety, health or technical reasons, please fill in the appropriate information below and mail or FAX to: Electronic Components Industry Associatio

9、n EIA Standards & Technology Department 2214 Rock Hill Rd., Suite 265 Herndon, VA 20170 FAX: (571-323-0245) Document No.: Document Title: Submitters Name: Telephone No.: FAX No.: e-mail: Address: Urgency of Change: Immediate: At next revision: Problem Area: a. Clause Number and /or Drawing: b. Recom

10、mended Changes: c. Reason/Rationale for Recommendation: Additional Remarks: Signature: Date: FOR ECIA USE ONLY Responsible Committee: Chairman: Date comments forwarded to Committee Chairman: Revision History Revision letter Project number Publication date Additions, changes and deletions - SP-1016 D

11、ecember 1969 Initially published in EIA RS-364 A SP-1413 July 1983 Was published as EIA RS-364-08A B SP-4031 May 1998 C SP-5345.04 Added units to dimensions in paragraph 2.1.2 and 4.2 Correct spelling of “outside” in paragraph 4.4.4 Revised paragraph 5.2 Revised text under paragraph 6 Revised paragraph 6.3 Revised paragraph 6.7 Electronic Components Industry Association 2214 Rock Hill Road, Suite 265 * Herndon, VA 20170 * tel 571-323-0294 * fax 571-323-0245 www.ecianow.org