ECA EIA-200-B-2018 Circular Waveguides and Flanges.pdf

《ECA EIA-200-B-2018 Circular Waveguides and Flanges.pdf》由会员分享，可在线阅读，更多相关《ECA EIA-200-B-2018 Circular Waveguides and Flanges.pdf（24页珍藏版）》请在麦多课文档分享上搜索。

1、EIA SPECIFICATIONCircular Waveguides and Flanges EIA-200-B (Revision of EIA-RS-200-A) April 2018 Electronic Components Industry Association EIA-RS-200-BANSI/EIA-200-B-2018 Approved: April 24, 2018NOTICEEIA Engineering Specifications and Publications are designed to serve the public interest through

2、eliminating misunderstandings between manufacturers and purchasers, facilitating interchangeability and improvement of products, and assisting the purchaser in selecting and obtaining with minimum delay the proper product for his particular need. Existence of such Specifications and Publications sha

3、ll not in any respect preclude any member or nonmember of ECIA from manufacturing or selling products not conforming to such Specifications and Publications, nor shall the existence of such Specifications and Publications preclude their voluntary use by those other than ECIA members, whether the Spe

4、cification is to be used either domestically or internationally. NOTE The users attention is called to the possibility that compliance with this standard may require use of an invention covered by patent rights. By publication of this standard, no position is taken with respect to the validity of an

5、y such claim(s) or of any patent rights in connection therewith. If a patent holder has filed a statement of willingness to grant a license under these rights on reasonable and nondiscriminatory terms and conditions to applicants desiring to obtain such a license, then details may be obtained from t

6、he standards developer Neither the standards developer nor ANSI is responsible for identifying patents for which a license may be required by an American National Standard or for conducting inquiries into the legal validity or scope of those patents that are brought to their attention.This EIA Speci

7、fication is considered to have International Standardization implications, but the International Electrotechnical Commission activity has not progressed to the point where a valid comparison between the EIA Specification and the IEC document can be made. This Specification does not purport to addres

8、s all safety problems associated with its use or all applicable regulatory requirements. It is the responsibility of the user of this Specification to establish appropriate safety and health practices and to determine the applicability of regulatory limitations before its use. (From Standards Propos

9、al No. PN-5383, formulated under the cognizance of the CE-2.2 Committee on RF Connectors and Rigid Coax Connectors and previously published in EIA- RS-200A) Published by Electronic Components Industry Association 2018 EIA Standards & Technology Department 2214 Rock Hill Road, Suite 265 Herndon, VA 2

10、0170 PLEASE ! DONT VIOLATE THE LAW! This document is copyrighted by the ECIA and may not be reproduced without permission. Organizations may obtain permission to reproduce a limited number of copies through entering into a license agreement. For information, contact: IHS Markit 15 Inverness Way East

11、 Englewood, CO 80112-5704 or call USA and Canada (1-877-413-5186), International (303-397-7956) (This page left blank) i CONTENTS Clause Page 1. Introduction . 11.1 Scope . 12. Size 12.1 Definitions of Terminology 12.2 Out-of-Roundness . 12.3 Mean Wall Thickness . 12.4 Tolerances . 12.5 Wall Thickne

12、ss 12.6 Dimensions . 13. Frequency Range 24. Bow . 25. Material and Workmanship. 25.1 Workmanship: . 26. EIA Type Designation 36.1 Marking . 37. Packaging And Packing 3LIST OF TABLES Table Page Table 1 Dimensions, Tolerances, And Frequency Range For Rigid Circular Waveguides . 4ii LIST OF FIGURES Fi

13、gure Page Figure 1 0.875 Flange 6Figure 2 1.625 Flange 7Figure 3 2.125 Flange 8Figure 4 3.00 Flange 9Figure 5 4.00 Flange 10Figure 6 5.00 Flange 11Figure 7 6.25 Flange 12Figure 8 7.1875 Flange 13Figure 9 8.00 Flange 14Figure 10 9.1875 Flange 15EIA-200-B Page 1 Circular Waveguides (From EIA Standards

14、 Proposal No. PN-5383, formulated under the cognizance of the EIA CE-2.2 Committee on Circular Waveguides, and previously published as RS-200A) 1. Introduction 1.1 Scope This standard pertains exclusively to circular waveguide and their flanges. This standard does not apply to any semi-flexible tran

15、smission lines or connectors. It is the intent of this standard to provide complete mechanical interchangeability for all lines. 2. Size 2.1 Definitions of Terminology Diameter, Mean- The mean diameter (I.D. and O.D.) is the average, at one cross section, of the maximum and minimum measured diameter

16、s usually found at, or very close to, 90 from each other. Mean I.D. = .2.2 Out-of-Roundness Out-of-roundness of the inside of the waveguide is the total difference, found at any-one cross-section, between the individual maximum and minimum Inside Diameters which usually occurs at, or about, 90 from

17、each other. Out-of-roundness is not expressed as plus and minus. Out-of-Roundness = Max. I.D - Min. I.D. 2.3 Mean Wall Thickness Mean Wall thickness is defined as one-half the difference between corresponding mean inside and outside diameters at any cross section perpendicular to the longitudinal ax

18、is. 2.4 Tolerances The tolerance on mean diameters and the out-of-roundness are specified in Table . 2.5 Wall Thickness The actual wall thickness as measured at any point around the periphery shall not deviate from the mean wall thickness at that cross section by more than 10%. 2.6 Dimensions Dimens

19、ions and tolerances for the lines are specified in Table 1. Dimensions and tolerances for the connectors are shown on Figure 1 thru Figure 10. EIA-200-B Page 2 3. Frequency Range a. Recommended frequency range for each size is specified in Table b. Specified frequency range assumes operation in the

20、dominant (TE11) mode or in the circular electric (TE01) mode. c. Each specified frequency range for the TE01 mode operation is within 1.21 times the cutoff frequency for the TE01 mode and 0.91 times the cutoff frequency of the TE02 mode. Each specified frequency range for the TE11 mode operation is

21、within 1.15 times the cutoff frequency for the TE11 mode and 0.95 times the cutoff frequency of the TE21 mode. d. To permit selection of optimum waveguide sizes, two overlapping series are specified. 4. Bow a. Bow is the departure from a straight longitudinal line connecting any two points two feet

22、apart on the external surface of the waveguide. b. Bow shall not exceed 0.010 inch. c. Measurement of bow shall not be altered by gravity or any other forces. The size of a coaxial line is defined as the nominal outside diameter of the line, expressed in inches. The size of the connector is defined

23、by the nominal outside diameter of the line with which it is used. Metric dimensions are for reference only and are based upon 1.0 inch equals 25.4 mm. 5. Material and Workmanship To be specified by user. These waveguides and flanges are designed for copper alloys, aluminum alloys, and magnesium all

24、oys. The particular type of alloy and finish is to be specified by the user. Unless otherwise specified, means shall be provided to reduce to a minimum galvanic or other corrosive action, consistent with satisfactory electrical contact. Flanges are designed to accommodate standard cap screws and hex

25、 nuts. 5.1 Workmanship: The interior surfaces of the finished waveguide tubing and flanges shall be as free from burrs, die marks, chatter marks, inclusions, and scratches as best commercial practice will permit. Waveguides and flanges shall be commercially uniform in composition, as straight and sm

26、ooth from end to end, as uniform in wall thickness, and as free from dirt, grease, scale, and splinters as best commercial practice will permit. No folds or laps will be permitted. EIA-200-B Page 3 6. EIA Type Designation Type designation for circular waveguides shall be in the following form: W C 1

27、50 Waveguide Circular Nominal Inner Diameter X 100 inches (Table ) 6.1 Marking The legend containing the type designation shall be repeated at intervals no greater than twelve inches on each length of finished waveguide in such a way as not to deform inner surfaces beyond the tolerances specified in

28、 Table 1. 7. Packaging and Packing Each length of waveguide shall be suitably protected at both ends to prevent the entrance of foreign matter and protect ends. Packing shall be such as to assure that after shipping and handling, the waveguide shall meet the requirements of 3 and 4, and the toleranc

29、es specified in Table . Table 1 Dimensions, Tolerances, And Frequency Range For Rigid Circular Waveguides (All Dimensions in Inches) EIA DesignationFrequency Range (GHz) Inside Diameter Outside Diameter Nominal Wall ThicknessNominalI.D. (Ref)TE11 Mode (From-To) TE01 Mode (From-To) NominalTolerance+/

30、- Max Out-of-Roundness NominalTolerance+/- WC 2551 0.312 - 0.427 0.683 - 0.940 25.508 0.025 0.025 - - - - WC 2179 0.365 - 0.500 0.799 - 1.10 21.791 0.020 0.022 - - - - WC 1862 0.427- 0.586 0.936 - 1.29 18.616 0.020 0.019 - - - - WC 1590 0.500- 0.686 1.10 - 1.51 15.903 0.015 0.016 - - - - WC 1359 0.5

31、86- 0.803 1.28 - 1.77 13.585 0.015 0.014 - - - - WC 1161 0.686- 0.939 1.50 - 2.07 11.606 0.010 0.012 - - - - WC 992 0.803- 1.10 1.76 - 2.42 9.915 0.010 0.010 - - - - WC 847 0.939- 1.29 2.06 - 2.83 8.470 0.008 0.008 - - - - WC 724 1.10 - 1.51 2.41 - 3.31 7.235 0.007 0.007 - - - - WC 618 1.29 - 1.76 2

32、.82 - 3.88 6.181 0.006 0.006 6.781 0.008 0.300 - WC 528 1.51 - 2.07 3.30 - 4.54 5.280 0.005 0.005 5.880 0.007 0.300 - WC 385 2.07 - 2.83 4.52 - 6.22 3.853 0.004 0.005 4.253 0.006 0.200 - WC 329 2.42 - 3.31 5.29 - 7.28 3.292 0.003 0.003 3.692 0.005 0.200 - WC 281 2.83 - 3.88 6.19 - 8.53 2.812 0.003 0

33、.003 3.112 0.005 0.150 - WC 240 3.31 - 4.54 7.25 - 9.98 2.403 0.0025 0.002 2.703 0.004 0.150 - WC 205 3.89 - 5.33 8.51 - 11.7 2.047 0.0020 0.002 2.307 0.004 0.130 2 3/64 WC 175 4.54 - 6.23 9.95 - 13.7 1.750 0.0015 0.0015 2.010 0.004 0.130 1 3/4 WC 150 5.30 - 7.27 11.6 - 16.0 1.500 0.0015 0.0015 1.70

34、0 0.003 0.100 1 1/2 WC 128 6.21 - 8.51 13.6 - 18.7 1.281 0.0013 0.0013 1.441 0.003 0.080 1 9/32 WC 109 7.27 - 9.97 15.9 - 21.9 1.094 0.0010 0.0011 1.224 0.003 0.065 1 3/32 WC 94 8.49 - 11.6 18.6 - 25.6 0.938 0.0009 0.0009 1.068 0.003 0.065 15/16 WC 80 9.97 - 13.7 21.9 - 30.1 0.797 0.0008 0.0008 0.89

35、7 0.0025 0.050 51/64 WC 69 11.6 - 15.9 25.3 - 34.9 0.688 0.0007 0.0007 0.788 0.0025 0.050 11/16 EIA-200-BPage4EIA DesignationFrequency Range (GHz) Inside Diameter Outside Diameter Nominal Wall ThicknessNominalI.D. (Ref)TE11 Mode (From-To) TE01 Mode (From-To) NominalTolerance+/- Max Out-of-Roundness

36、NominalTolerance+/- WC 59 13.4 - 18.4 29.3 - 40.4 0.594 0.0006 0.0006 0.674 0.0025 0.040 19/32 WC 50 15.9 - 21.8 34.8 - 48.0 0.500 0.0005 0.0005 0.580 0.002 0.040 1/2 WC 44 18.2 - 24.9 39.8 - 54.8 0.438 0.00045 0.0004 0.518 0.002 0.040 7/16 WC 38 21.2 - 29.1 46.4 - 63.9 0.375 0.00038 0.0004 0.435 0.

37、002 0.030 3/8 WC 33 24.3 - 33.2 53.1 - 73.1 0.328 0.00033 0.0003 0.388 0.002 0.030 21/64 WC 28 28.3 - 38.8 61.9 - 85.2 0.281 0.00028 0.0001 0.341 0.002 0.030 9/32 WC 25 31.8 - 43.6 69.7 - 95.9 0.250 0.00025 0.0001 0.290 0.002 0.020 1/4 WC 22 36.4 - 49.8 79.6 - 110 0.219 0.00025 0.0001 0.259 0.002 0.

38、020 7/32 WC 19 42.4 - 58.1 92.9 - 128 0.188 0.00025 0.00007 0.228 0.002 0.020 3/16 WC 17 46.3 - 63.5 101 - 139 0.172 0.00025 0.00007 0.212 0.002 0.020 11/64 WC 14 56.6 - 77.5 124 - 171 0.141 0.00025 0.00005 0.181 0.002 0.020 9/64 WC 13 63.5 - 87.2 139 - 192 0.125 0.00025 0.00005 0.155 0.002 0.015 1/

39、8 WC 11 72.7 - 99.7 159 - 219 0.109 0.00025 0.00005 0.139 0.002 0.015 7/64 WC 9 84.8 - 116 186 - 256 0.094 0.00025 0.00005 0.124 0.002 0.015 3/32 EIA-200-BPage5EIA-200-B Page 6 Figure 1 0.875 Flange EIA-200-B Page 7 Figure 2 1.625 Flange EIA-200-B Page 8 Figure 3 2.125 Flange EIA-200-B Page 9 Figure

40、 4 3.00 Flange EIA-200-B Page 10 Figure 5 4.00 Flange EIA-200-B Page 11 Figure 6 5.00 Flange EIA-200-B Page 12 Figure 7 6.25 Flange EIA-200-B Page 13 Figure 8 7.1875 Flange EIA-200-B Page 14 Figure 9 8.00 Flange EIA-200-B Page 15 Figure 10 9.1875 Flange ECIA Document Improvement Proposal If in the r

41、eview or use of this document, a potential change is made evident for safety, health or technical reasons, please fill in the appropriate information below and mail or FAX to: Electronic Components Industry Association EIA Standards & Technology Department 2214 Rock Hill Rd., Suite 265 Herndon, VA 2

42、0170 FAX: (571-323-0245) Document No.: Document Title: Submitters Name: Telephone No.: FAX No.: e-mail:Address: Urgency of Change: Immediate: At next revision: Problem Area: a. clause Number and /or Drawing: b. Recommended Changes: c. Reason/Rationale for Recommendation: Additional Remarks: Signatur

43、e: Date: FOR ECIA USE ONLY Responsible Committee: Chairman: Date comments forwarded to Committee Chairman: Revision History Revision letter Project number Publication date Additions, changes and deletions - January 1958 Initial publicationA March 1965 RevisionB PN-5383 2017 RevisionElectronic Components Industry Association 2214 Rock Hill Road, Suite 265 * Herndon, VA 20170 * tel 571-323-0294 * fax 571-323-0245 www.ecianow.org