DLA MS77068 REV B-2003 TERMINAL LUG SOLDER TYPE PHOSPHOR BRONZE STAMPING LOCKING TYPE 45 DEG TWO HOLE《联轴型2孔45 DEG 磷青铜冲压片 焊料型终端接线片》.pdf

《DLA MS77068 REV B-2003 TERMINAL LUG SOLDER TYPE PHOSPHOR BRONZE STAMPING LOCKING TYPE 45 DEG TWO HOLE《联轴型2孔45 DEG 磷青铜冲压片 焊料型终端接线片》.pdf》由会员分享，可在线阅读，更多相关《DLA MS77068 REV B-2003 TERMINAL LUG SOLDER TYPE PHOSPHOR BRONZE STAMPING LOCKING TYPE 45 DEG TWO HOLE《联轴型2孔45 DEG 磷青铜冲压片 焊料型终端接线片》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、 AMSC N/A FSC 5940 INCH-POUND MS77068B 17 December 2003 SUPERSEDING MS77068A 15 December 1989 DETAIL SPECIFICATION SHEET TERMINAL, LUG, SOLDER TYPE, PHOSPHOR BRONZE STAMPING, LOCKING TYPE, 45, TWO HOLE Inactive for new design after 18 October 2000. This specification sheet is approved for use by all

2、 departments and agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-15659. View at “X“X“416414.018 .003451564A5163322 Holes18332RFIGURE 1. Terminal dimensions. Provided by IHSNot for ResaleNo reprod

3、uction or networking permitted without license from IHS-,-,-MS77068B 2 TABLE I. Dash numbers and dimensions. A Dash no. Screw size Max. Min. AWG1size 1 4 0.127 0.115 2 6 0.153 0.141 3 8 0.179 0.167 4 10 0.205 0.193 12 to 20 1American Wire Gauge. REQUIREMENTS: 1. Material: Phosphor bronze strip alloy

4、 C50500 (1.3 percent tin), in accordance with ASTM B 508 (DOD adopted), having a minimum temper of H02. As an alternative material, copper, strip alloy C42500 in accordance with ASTM B 591 (DOD adopted), having a minimum temper of H02 may be used. 2. Finish: Tinned; electrodeposited over entire surf

5、ace in accordance with ASTM B 545 (DoD adopted) and ASTM B 339 (DoD adopted). Minimum thickness 0.0005 inches. NOTES: 1. Dimensions are in inches. 2. Unless otherwise specified, tolerance is 0.015, angles 2 degrees. 3. Remove all burrs. 4. Referenced documents of issue in effect on date of invitatio

6、n for bids shall apply. 5. In the event of a conflict between the text of this document and the references cited herein, the text of this document shall take precedence. 6. The part or identifying number (PIN) consists of the letters MS, the specification sheet number, and a dash number taken from t

7、able I. MS 77068 - 3 CAHNGES FROM PREVIOUS ISSUE: Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of those changes. Dash number Specification sheet number MS prefix Provided by IHSNot for ResaleNo reproduction or networking pe

8、rmitted without license from IHS-,-,-MS77068B 3 Custodians: Preparing Activity: Army - AV Navy - SH Air Force - 11 DLA - GS2 (Project 5940-1444) Review Activities: Army - CR4, MI Navy - MC Air Force - 99 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-