DLA MS20029 REV G-2010 CONNECTORS RECEPTACLE ELECTRICAL JAM NUT MOUNTING SOLDER TYPE BAYONET COUPLING CLASS P SERIES I.pdf

《DLA MS20029 REV G-2010 CONNECTORS RECEPTACLE ELECTRICAL JAM NUT MOUNTING SOLDER TYPE BAYONET COUPLING CLASS P SERIES I.pdf》由会员分享，可在线阅读，更多相关《DLA MS20029 REV G-2010 CONNECTORS RECEPTACLE ELECTRICAL JAM NUT MOUNTING SOLDER TYPE BAYONET COUPLING CLASS P SERIES I.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、 DETAIL SPECIFICATION SHEET CONNECTORS, RECEPTACLE, ELECTRICAL, JAM NUT MOUNTING, SOLDER TYPE, BAYONET COUPLING, CLASS P, SERIES I This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall co

2、nsist of this specification sheet and MIL-DTL-27599. FIGURE 1. Receptacle, jam nut mounting. AMSC N/A FSC 5935 INCH - POUNDMS20029G 31 August 2010 SUPERSEDING MS20029F 20 May 2005 Inactive for new design after 7 December 1998.Provided by IHSNot for ResaleNo reproduction or networking permitted witho

3、ut license from IHS-,-,-MS20029G 2 FIGURE 1. Receptacle, jam nut mounting - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS20029G 3 NOTES: 1. Dimensions are in inches. Metric equivalents are given for information only. 2. Insert front s

4、urface shall be flat within .005 T.I.R. 3. Diameters A, D, M, Q and Z shall be concentric within .015 T.I.R. 4. Diameters D and I shall be concentric within .005 T.I.R. at MMC. 5. Diameter A with respect to diameter B, and diameter D with respect to diameter N, shall be concentric at MMC. 6. Sides o

5、f groove may have 5 max taper. 7. .062 .005 dia., 3 lockwire holes, shell sizes 9 through 25. 8. Normal keyway position. For other keyway positions, see MIL-DTL-27599. 9. The point at which a gauge pin having the same basic diameter as the mating contact and a square face, touches socket contact spr

6、ing. 10. The gauge features for GG shall be CC smaller than their MMC size. FIGURE 1. Receptacle, jam nut mounting - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS20029G 4 Inches mm Inches mm Inches mm Inches mm 0.001 0.0254 0.016 0.40

7、 0.078 1.98 0.390 9.90 0.002 0.051 0.020 0.51 0.094 2.39 0.565 14.35 0.005 0.127 0.036 0.91 0.116 2.95 0.576 14.63 0.006 0.152 0.040 1.02 0.125 3.17 0.599 15.21 0.010 0.254 0.047 1.19 0.126 3.20 0.915 23.24 0.011 0.28 0.062 1.57 0.156 3.96 0.015 0.38 0.063 1.60 0.266 6.76 FIGURE 1. Receptacle, jam n

8、ut mounting - Continued. TABLE I. Dimensions. 1/ 2/ Shell Size A dia + .001 - .005 B dia + .000 - .016 C BSC D dia + .005 - .001 H hex + .017 - .016 I dia .005 CC 9 .572 (14.53) .662 (16.81) .100 (2.54) .442 (11.22) .875 (22.22) .296 (7.52) .010 (.254) 11 .700 (17.78) .810 (20.57) .570 (14.48) 1.000

9、 (25.40) .413 (10.50) 13 .850 (21.60) .960 (24.38) .687 (17.45) 1.188 (30.17) .527 (13.38) 15 .975 (24.76) 1.085 (27.56) .812 (20.62) 1.312 (33.32) .652 (16.56) 17 1.100 (27.94) 1.210 (30.73) .937 (23.80) 1.438 (36.52) .777 (19.73) 19 1.207 (30.65) 1.317 (33.45) 1.042 (26.46) 1.562 (39.67) .866 (22.

10、00) 21 1.332 (33.83 1.442 (36.62) 1.167 (29.64) 1.688 (42.87) .991 (25.17) 23 1.457 (37.01) 1.567 (39.80) 1.292 (32.81) 1.812 (46.02) 1.116 (28.34) 25 1.582 (40.18) 1.692 (42.97) .109 (2.77) 1.417 (35.60) 2.000 (50.80) 1.241 (31.52) See notes at end of table. Provided by IHSNot for ResaleNo reproduc

11、tion or networking permitted without license from IHS-,-,-MS20029G 5 TABLE I. Dimensions - Continued. 1/ 2/ Shell size K + .011 - .010 M Thread class 2A, plated, UNEF N dia + .005 - .006 O + .000 - .010 Q dia .016 S .016 9 .109 (2.77) .6875 - 24 .492 (12.50) .655 (16.64) 1.188 (30.17) 1.062 (26.97)

12、11 .8125 - 20 .620 (15.75) .755 (19.17) 1.375 (34.92) 1.250 (31.75) 13 1.0000 - 20 .769 (19.53) .942 (23.92) 1.500 (38.10) 1.375 (34.92) 15 1.1250 - 18 .894 (22.70) 1.066 (27.07) 1.625 (41.27) 1.500 (38.10) 17 1.2500 - 18 1.019 (25.88) 1.191 (30.25) 1.750 (44.45) 1.625 (41.27) 19 1.3750 - 18 1.124 (

13、28.55) 1.316 (33.42) 1.938 (49.22) 1.812 (46.02) 21 .140 (3.55) 1.5000 - 18 1.249 (31.72) 1.441 (36.60) 2.062 (52.37) 1.938 (49.22) 23 1.6250 - 18 1.374 (34.89) 1.566 (39.77) 2.188 (55.57) 2.062 (52.37) 25 1.7500 - 18 1.499 (38.07) 1.691 (42.95) 2.312 (58.72) 2.188 (55.57) See notes at end of table.

14、 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS20029G 6 TABLE I. Dimensions - Continued. 1/ 2/ Shell size T dia + .011 - .000 V dia .011 W + .017 - .000 X + .005 - .001 Y dia .005 Z dia + .006 - .005 9 .516 (13.10) .476 (12.10) .125 (3.17) .094 (

15、2.38) .045 (1.14) .777 (19.73) 11 .642 (16.30) .602 (15.30) .965 (24.51) 13 .766 (19.45) .726 (18.44) 1.090 (27.68) 15 .892 (22.65) .852 (21.64) 1.215 (30.86) 17 1.018 (25.86) .978 (24.84) 1.340 (34.04) 19 1.142 (29.01) 1.102 (28.00) .141 (3.58) .075 (1.90) 1.449 (36.80) 21 1.268 (32.20) 1.228 (31.2

16、0) 1.574 (39.98) 23 1.392 (35.35) 1.352 (34.34) 1.699 (43.15) 25 1.518 (38.55) 1.478 (37.54) 1.824 (46.33) See notes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS20029G 7 TABLE I. Dimensions - Continued. 1/ 2/ Shell size N dia M

17、in HH dia Max JJ max Recommended packing -ring 9 .317 (8.05) .625 (15.87) .688 (17.47) SAE-AS3578-019 11 .434 (11.02) .750 (19.05) SAE-AS3578-022 13 .548 (13.92) .875 (22.22) SAE-AS3578-024 15 .673 (17.09) 1.000 (25.40) SAE-AS3578-026 17 .798 (20.27) 1.125 (28.57) SAE-AS3578-028 19 .899 (22.83) 1.25

18、0 (31.75) .719 (18.26) SAE-AS3578-128 21 1.024 (26.01) 1.375 (34.92) .812 (20.62) SAE-AS3578-130 23 1.149 (29.18) 1.500 (38.10) SAE-AS3578-132 25 1.274 (32.36) 1.625 (41.27) SAE-AS3578-134 1/ Dimensions are in inches. 2/ Metric equivalents are given for information only. REQUIREMENTS: Dimensions and

19、 configurations: See figure 1 and table I. This connector mates with MS20027 and MS20028. Insert arrangement shall be in accordance with MIL-STD-1560. Recommended packing for o-ring shall be in accordance with SAE-AS3578. Recommended packing is for dimensions only. Material is optional. Provided by

20、IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS20029G 8 Part or Identifying Number (PIN) example: MS20029 P 13 A 96 P A MS number Class Shell size Finish (color) Insert arrangement Style Polarizing position (No letter is required for normal position) Changes

21、from previous issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. Referenced documents. In addition to MIL-DTL-27599, this document references the following: MIL-STD-1560 MS20027 MS20028 SAE-AS3578 CONCLUDIN

22、G MATERIAL Custodians: Preparing activity: Air Force - 85 DLA - CC DLA - CC Review activities: Air Force - 99 (Project 5935-2010-099) DLA - IS NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-