DLA MS3481 REV A-2007 TOOL CONNECTOR ASSEMBLY FOR MIL-DTL-26482 CONNECTORS《MIL-DTL-26482 连接器用连接器组装工具》.pdf

《DLA MS3481 REV A-2007 TOOL CONNECTOR ASSEMBLY FOR MIL-DTL-26482 CONNECTORS《MIL-DTL-26482 连接器用连接器组装工具》.pdf》由会员分享，可在线阅读，更多相关《DLA MS3481 REV A-2007 TOOL CONNECTOR ASSEMBLY FOR MIL-DTL-26482 CONNECTORS《MIL-DTL-26482 连接器用连接器组装工具》.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、 DETAIL SPECIFICATION SHEET TOOL, CONNECTOR ASSEMBLY, FOR MIL-DTL-26482 CONNECTORS This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-26

2、482. FIGURE 1. Tool, dimensions and configurations. AMSC N/A FSC 5935 INCH-POUNDMS3481A 1 March 2007 SUPERSEDING MS3481 (NAVY) 21 January 1970 Reactivated after 1 March 2007 and may be used for new and existing designs and acquisitions.Provided by IHSNot for ResaleNo reproduction or networking permi

3、tted without license from IHS-,-,-MS3481A 2FIGURE 1. Tool, dimensions and configurations - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS3481A 3Dash number Shell size A .030 B .060 C approx D approx E dia approx F dia + .001 - .005 -08

4、 8 .473 (.019) .357 (.014) -10 10 .590 (.023) .485 (.019) -12 12 .750 (.030) .597 (.024) -14 14 1.250 (.049) .875 (.034) .722 (.028) -16 16 1.000 (.039) .847 (.033) -18 18 .380 (.015) .410 (.016) .455 (.018) 1.125 (.044) .947 (.037) -20 20 1.250 (.049) 1.072 (.042) -22 22 1.375 (.054) 1.197 (.047) -

5、24 24 .425 (.017) 2.000 (.079) .495 (.019) .540 (.021) 1.500 (.059) 1.322 (.052) Shell size G dia min H dia + .005 - .001 J dia + .001 - .005 K min L dia + .005 - .006 M dia + .001 - .010 8 .292 (.011) .362 (.014) .473 (.019) .412 (.016) .402 (.016) 10 .409 (.016) .490 (.019) .590 (.023) .540 (.021)

6、 .530 (.021) 12 .523 (.021) .607 (.024) .750 (.030) .689 (.027) .679 (.027) 14 .648 (.026) .732 (.029) .875 (.034) .814 (.032) .804 (.032) 16 .772 (.030) .857 (.034) 1.000 (.039) .939 (.037) .929 (.037) 18 .862 (.034) .962 (.038) 1.125 (.044).281 (.011) 1.039 (.041) 1.029 (.041)20 .987 (.039) 1.087

7、(.043) 1.250 (.049) 1.164 (.046) 1.154 (.045)22 1.111 (.044) 1.212 (.048) 1.375 (.054) 1.289 (.051) 1.279 (.050)24 1.237 (.049) 1.337 (.053) 1.500 (.059).343 (.014) 1.414 (.056) 1.404 (.055)NOTES: 1. Dimensions are in inches. Metric equivalents are given for information only. 2. Unless otherwise spe

8、cified, tolerances shall be .016 for decimals. Angular tolerances are TP. FIGURE 1. Tool, dimensions and configurations - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS3481A 4REQUIREMENTS: Dimensions and configuration: See figure 1. Th

9、ese tools are for use with connectors in accordance with MIL-DTL-26482. Shell material: High grade aluminum alloy. Handle material: Die cast aluminum alloy in accordance with ASTM-B85. Finish: Nickel plate in accordance with SAE-AMS-QQ-N-290. All burrs and sharp edges shall be removed. PIN example:

10、MS3481 - 24 MS number Dash number Changes from previous issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. Referenced documents. In addition to MIL-DTL-26482, this document references the following: ASTM-B8

11、5 SAE-AMS-QQ-N-290 CONCLUDING MATERIAL Custodians: Preparing activity: Army - CR DLA - CC Navy - AS DLA - CC (Project 5935-4656-019) Review activities: Army - GL Navy - EC NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-