DLA MIL-M-87958-1978 MARKERS BLANKS PRESSURE SENSITIVE ADHESIVE WIRE OR CABLE MARKER AND IDENTIFICATION LABEL《压敏粘着准绳或电缆标志和识别标签 信文标记》.pdf

《DLA MIL-M-87958-1978 MARKERS BLANKS PRESSURE SENSITIVE ADHESIVE WIRE OR CABLE MARKER AND IDENTIFICATION LABEL《压敏粘着准绳或电缆标志和识别标签 信文标记》.pdf》由会员分享，可在线阅读，更多相关《DLA MIL-M-87958-1978 MARKERS BLANKS PRESSURE SENSITIVE ADHESIVE WIRE OR CABLE MARKER AND IDENTIFICATION LABEL《压敏粘着准绳或电缆标志和识别标签 信文标记》.pdf（16页珍藏版）》请在麦多课文档分享上搜索。

1、specification is approved for use by Air Force, Department of the De- fense, end is available for we by all Departments and Agencies of the Departnent -of Defense. 1. SCOPE 1.1 Scow. “.S specification covers pressure sensitive adhesive backed wire marker and identification label blanks intended to b

2、e custom marked by the wer M computer print-out equipment. 1.2 Classification. 1.2.1 bntirwoUS xXI.S 1.204 canfinuration. Marker blanks shall be tbnished in one of the con=- figurations described in Appendix A (see 6.2). The CanfigratAon identi- fier consists of the lettemnunber .oombination shown i

3、n the first collumn of the tabulation in Appendix A. 2. AppLscABLEmcuHENTs 2.1 me follouing documents -of the issue in effect on date of invitation for bids or request for proposal form a part of this specification to the extent specified herein: Beneficial comments (recoranendation, additions, dele

4、tions) and any perti- nent data which may be of we in improving this document should be addressed tot AFZC cAso/II)DB, Federal Center, Battle Creek, MI 49016 by-using the self-addressed Standardization Ibcument Improvement ProposaJ. (DD firm ,1426) appe- at the end of this doCutuent or by letter. i

5、I Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-I,aL-EL87958 (um) NATIONAL YOTOR FRFIGHT TRAFFIC ASSOCIATION, DJC. National bbtor Freight Classificati

6、on (Application for copies should be addressed to American Trucking Associations, ATTN: Tariff Order Section, 1616 P Street, N.B., Washington, DC 20036.) UNIFORM CLASSIFTCATION COMMITTEE . Uniform Freight Classification (Application for copies should be addressed to the Uniform Classification (!anmi

7、ttee, Room 202 Union Station, 516 W. Jackson Blvd., Chicago, IL 60606.) U.S. DEPAITMZNT OF COMMERCE Standard Alphabet for Highway Signs (Application for copies should be addressed to the Superintendent of Docu- ments, U.S. Government Printing Office, Haasmgton, DC 20402.) 3. REQUIRENENTS 3.1 E. No d

8、ata is. required by this specification unless specified in the contract or order (see 6.2). 3.2 First article approval. Nhen specified by the procuring activity (see 6.2) the marker blanks shall be a product that has been inspected and passed he first article inspection of 4.5.1. 3.3 WIstmction. Mar

9、ker blank material shall consist of a flexible backing, adhesive and liner. After marking and removal from the liner, the backing (with adhesive).constitutes the finished marker or identification label. 3.3.1 ,E?ackLn. Tne marking -face of the backing shall be coated with an ink receptive finish, sm

10、ooth and uniform, and free from blisters, wrinkles cracks and scratches. Backing material type shall be as specified (see 1.2.lj. 3.3.2 Adhesive. The adhesive shall be a pressure-sensitive, permanent type. It shall be water insoluble, homogeneous, and shall b coated m a smooth layer on one side of t

11、he back-. The adhesive shall require no solvent, heat, or other preparation prior to application. Adhesive shall be of a type. that v611 adhere to metal, plastic, or its okm printable backing. 3.3.3 Liner. A liner of material suitable for the purpose intended shall be used to protect the adhesive. I

12、t shall be capable of being quickly removed for fast, distortion-free application. The liner shall not split, tear, or leave a residue on the adhesive when the marker or label is removed. 3.4 lhe I Label Blanks. 3.L+.l Form F. Unless otherwise specified by the procuring activity (see 6.2), Form F ma

13、rker blanks shall be furmished in a continuous series of sheets.fandolded and perforated every 12 inches with a margin on each edge punched to accommodate standard computer print-out equipment and with the backing cut into individual label blanks (see Appendix A) . 3 Provided by IHSNot for ResaleNo

14、reproduction or networking permitted without license from IHS-,-,-MILI-%-87958 (USAF) 3.4.2 Form R. Unless otherwise specified by the procuring activity (see 6.21 Form R marker blanks shall be furnished in continuous rolls with a margin on each edge punched to.accommodate standard computer print-out

15、 equipment and with the backing cut into widths or individual label blanks (see Appendix A). 3.rC.2.1 Rolls. Form R miterial shall be supplied wound with the adhesive side in, on a core of sufficient rigidity to prevent distortion of the roll under normal conditions of transportation and use. ?he in

16、side diameter of the core shall be 3 2 1/16 inches. 3.4.3 Splicing. A maximum of 10% of the materiliner only. Splices in Form F material shall not interfere with the fan-fold or change the dimen- sions of the sheet. 3.4.3.1 slicing tape. Splicing tape with pressure sksitive adhesive shall have a nom

17、inal thickness of .O025 inch and a width of 1.0.inch. The spllcing tape shall have a minimm of 38 oz. adhesion after either 20 hours at 1500F or 28 days at room temperature. 3.5 Color. Marker blanks shall be furnished in the color specified by the procuring activity (see 6.2). Colors shall conform t

18、o the requirements of Class I of MIIIGSlOk. 3 . 6 Dimensions . 3.6.1 Thickness. The thickness of the backing and adhesive shall be 0.0034 i 0.005 when tested per ASTH D1000-70a, sections 14 to 18. 3.6.2 Length. Unless otherwise specified by the procuring activity, -the number of sheets per package (

19、Form F) shall be 250 f 3 and the length of rolJ. (Form R) shall be 100 1 2 feet when tested per AST“ M000-70a, sections 7 to 12. 3.6.3 Vidth and other dimensbns. All dimensions are in inches. commercial tolerances apply. Vidth and other detailed diwnsions, when .tested per AS934 m000-70a, sections 7

20、7 to 80, shall be as shown in the applicable configuration (see Appendix A). 3.7 Mechanical properties. 3.7.1 Adhesion to steel, The adhesion to steel, when tested per ASW MOO- 7Oa, sectinns 33 to 41, shall be not less than 37 OZ. per inch-of width. . 3.7.2 Adhesion to back%. The adhesion to backing

21、, when tested per AS“ Dl000“7Oa, sections 33 to 41, shall be not less than If; OZ. per inch of width. 3.7.3 Breaking strength and elongation. lhe breaking stnength, when tested per AS93-1 D1000-70a, sections 19 to 25, shall be not less than 20 lbs. per inch f width and the elongation shall be 100$ m

22、inimum. . 3.8 Fmrironmental requirements. 3.8.1 Lm temperature flexabilitx. Phen tested as described in 4.!5.4,1 the specimens shall exhibit no visible evidence of cracking, splitting, or 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-loosening fr

23、om the backing. 3.8.2 High temperature exposure. When tested as described in 4.6.5.2 the specimens shall exhibit no visible evidence of blistering, separation of flags or unrolling. 3.8.3 Fluid resistance. Hhen tested in accordance with 4.6.5.3 and 4.6.5.4 the specimens shall exhibit no visible evid

24、ence oflooseness, and no edge lift greater than 1/8 inch. Upon completion of exposure to fluids, the adhesion to backing or steel shall be not less than 15 oz. per inch of width. g.8.1+ Flammability. Specimens shall be self-extinguishing when tested in accordance with ASTM D568. 3.8.5 Printability.

25、!the backing material shall accept and retain printing applied by any of the following: (a) (!anputer printer. Standard computer print-out equipment may be employed, with computer ribbon that has been demonstrated to provide perma- nent, legible markings when tested in accordance with this specifica

26、tion (See 6.3) ?I “ evmiter. Standard typewriters rdth carbon or inked ribbon may be employed. 3.8.5.1 Printing permanence. ;hen tested in accordance with 4.6.5.5 the printedeiy nine (9) inches long shall be laminated to a clean stainless steel plate with a second specimen, of the same size and type

27、, laminated directly over the first. or diecut or scored built-up pads made of the same material as the box. Fach box shall, be securely closed vlith tape as specified in 5.1.1.1. 5.1.2 Level C. lhrking materials and markers shall be packaged to afford adequate protection against physical damage dur

28、ing shipment from the supply source to the first receiving activity. ?“ne supplier may use his standard practice when it meets this requirement. 5.2 pack in Packing shall be level A, B, or C, as specified (see 6.2). 5.2.1 Level A, A quantity of marking materials or markers, of one descrip tion only,

29、 packaged as specified in 5.1, shall be packed in a snug-fitting fiberboard. shipping container conforming to style BSC or LWGL (as applica- ble), grade V2s of ?-,%636 ; or overseas type 2 load of PPP-J3-601. The inside of each PPP-E636 container packed with unboxed packages shall be fit- ted with a

30、 taped box liner conform$g to type CF, class weather-resistant, variety Di, grade V15c of PPP-E63;6. Each PPP-B-636 shipping container shall be closed, waterproofed, and reinforced in accordace with the appendix of the container specification. and v:aterproofed vth a scaled case liner conforming to

31、type I or II, grade C of -Il0547. Shipping con- Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-flIL-fl-B7758 76 W 7777706 0230321 2 m MIL-“87958 (USAF) tainers packed with waterproof packages need not be waterproofed. The weight of the contents of e

32、ach fiberboard container shall not exceed -65 pounds and for each wood container shall notexceed 150 pounds. 5.2.2 Level B. A quantity of marking materials or markers, of one descrip tion only, packaged as specified in 5.1, shall be packed in a snug-fitting fiberboard shippingcontainer conforming to

33、 style RSC or RSGL (as applic- zble), type CF (variety SR) or SF, class domestic, grade 275 or PPP-&. The inside of each container packed &th unboxed packages shall be fitted with a taped box liner conforming to class domestic, variety DW, grade 275 of PPP- B-636. &ch shipping container shall be clo

34、sed in accordance with method II as specified in the appendix cif PPP“i36. The weight of contents of each shippingccontainer shall not exceed 65 pounds. 5.2.2.1 hen specified (see 6.2), the fiberboard shipping container shall be a grade VC, or V4s fiberboard box fabricated .jn accordqce with PPP-EL

35、and closed in accordvlce with the appendix of the container specification. 5.2.3 Level C. Narking material and markers, packaged as specified in 5.1, shall be packed in manner to insure carrier acceptance and safe delivery at destination at the lowest transportationrate for such supplies. Containers

36、 shall be in accordance trith Uniform Freight Classification Mes or National btor Freight Classification Rules, as applicable. 5.3 Urkhg. In addition to any special marking required by the contract or order, interior packages and shipping containers shall. be marked in accord- ance with NIGSTD-129.

37、6.1 =ended use. The pressure sensitive adhesive backed marker blanks des- cribed herein a& intended primarily for use in the automated fabrication of kustom“ wire markers and labels for special application. The material and construction is such that markings can be applied by computer print-out equi

38、pment or by less aEtomated other methods to provide -shed markers and labels that are fluid resistant and flame retardant. Although the material lends itself particularly to wire and czble identification, its use need not be restricted to such applications. 6.2 Ordering data. Procurement documents s

39、hould specify the following: (a) Title, number and .date of this specification. (b) Color (see 1.2.2). (c) Form (see 1.2.3 and 3.4). (d) Cbnfiguration (see 1.2.4 and Appendix A). (e) %aiver of length, if required (see 3.2). (f) mantity. (g) First article approval, if required (see 3.2). (h) Addition

40、al data, if required (see 3.1). 9 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-custodian Air Force - 99 10 Air Force - 39 eoject No - 76904952 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-APFEND

41、IX A 11 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-“87758 76 7777906 0230324 8 APPENDIX A CONFIGURATIONS FORM R (ROLL) CONFIGURATIONS PERFORATIONS 6LANK SIZE 8r SPACING HORIZ, H OVER- NO.OF B C D-VERT F G ALL BLANKS SEE A-NQ .WIDTH LENGTHSPA

42、CING E SPACING SPACING WIDTH PER LIN. FIG. WIDE (INCH) (INCH) (INCH) NO. (INCH) (INCH) (INCH) FOOT I . 7 1.50 CONTINUOUS NONE 12.00 - 2 4 1.50 2.90 3.00 5 1.60 3.00 7.30 16 2 2 1.50 2.90 6.00 I ENTER 6.00 4.10 4 L FORM F (FAN-FOLD) CONFIGURATIONS BLANK SIZE & SPACING PERFORATIONS VERTICAL HORIZ. I H

43、 OVER- 0 C D-VERT F G ALL SEE A-NO. WIDTH LENQTH SPACING E SPACINGSPACING WlDTk NO. FIG. WIDE (INCH) (INCH) (INCH ) NO. (INCH) (INCH ) (INCH) FI 3 12 a90 i25 -33 NONE .33. 13.00 NONE .33 I1.00 11.1 NO. OF ?ER SHEET 432 360 48 Provided by IHSNot for ResaleNo reproduction or networking permitted witho

44、ut license from IHS-,-,- H-OVERALL WIDTH MIL-Pi- &958( USAF) APPENDIX +“B-BLANK WIDTH NOTES: A-NO. OF PLACES NOTE 2.) 1. DIMENSIONS ARE IN INCHES. TOLERANCES: .L= 1 fl .XX=f.03 2.BACKING SLIT INTO BLANK WIDTHS AS SHOWN? 32 3.BOTH MARGINS PIERCED WITH .I56 DIAMETER HOLES ON L INBH CENTERS,HORlZON.TAL

45、LY ON LINE AS SHOWN. 2- 11.2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-M-87958 76 W 7779706 0230326 L M : 4 ,-MARKER BLANK F-SPACING-*+ I 7 +-.I TYP. SPACING OF VERTICAL I PERFORATIONS E- NO. OF PLACES (NOTE 4.) B-BLANK WIDTH A- NO. OF PLA

46、CES NOTES: (NOTE 2,) .“ 1, DIMENSIONS ARE IN INCHES. TOLERANCES: 7 3: 9 .XX=f.03. x *I xx 32 ZBACKING CUT INTO INDIVIDUAL MARKER BLANKS, EACH WITH LENGTH, WIDTH,& SPACING AS INDICATED. CORNERS ROUNDED p,6. RADIUS, 3.BOTH MARGINS PIERCED WITH .I56 DIAMETER HOLES ON ,& INCH CENTERS ALINER PERFORATED A

47、S INDICATED TO FACILITATE SEPARATION OF HORIZONTALLY ON LINE AS SHOWN. BLANKS. 11.3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-M-B795B 76 W 9997906 0230327 3 m -r / LG SPACING OF HORIZONTAL PERFORATIONS BLANK WIDTH (.NOTE 4.) A- NO. OF PLACE

48、S (NOTE 2.) NOTES: x +I * C. DIMENSIONS ARE IN INCHES. TOLERANCES: =32 9.xx=*03 2. BACKING GUT INTO INDIVIDUAL MARKER BLANKS,ECH WITH LENGTH, 3. BOTH MARGINS PIERCED WITH .I56 DIAMETER HOLES ON.,!$INCH . CENTERS, HORIZONTALLY ON THE CINE AS SHOWN. +.LINER PERFORATFD AS INDICATED TO FACILITATE SEPARA

49、TION OF WIDTH, SPACING AS INDICATED. CORNERS ROUNDED MAX. RADIUS. BLANKS. 11.4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-I H-OVERALL WIDTH- USAF) MARKER BLANK II I I. II -C“C“- II -t+“+- Provided by IHSNot for ResaleNo reproduction or networkin