DLA MIL-DTL-642 5 C-2013 PLUGS TELEPHONE (TYPE PJ-068).pdf

《DLA MIL-DTL-642 5 C-2013 PLUGS TELEPHONE (TYPE PJ-068).pdf》由会员分享，可在线阅读，更多相关《DLA MIL-DTL-642 5 C-2013 PLUGS TELEPHONE (TYPE PJ-068).pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、 MIL-DTL-642/5C 25 July 2013 SUPERSEDING MIL-DTL-642/5B 9 June 2003 DETAIL SPECIFICATION SHEET PLUGS, TELEPHONE (TYPE PJ-068) This specification is approved for use by all Departments and Cgencies of the Department of Defense. The requirements for acquiring the product described herein shall consist

2、 of this specification sheet and MIL-DTL-642. FIGURE 1. Dimensions and configuration. AMSC N/A FSC 5935 INCH-POUND Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-642/5C 2 Inch/mm conversion chart Inches mm Inches mm Inches mm .002 .05 .207 5

3、.26 .620 15.75 .005 .13 .218 5.54 .676 17.17 .008 .20 .281 7.14 .750 19.05 .015 .38 .296 7.52 .781 19.84 .020 .51 .340 8.64 .905 22.99 .045 1.14 .343 8.71 .967 24.56 .093 2.36 .390 9.91 1.093 27.76 .122 3.10 .406 10.31 2.046 51.97 .150 3.81 .4375 11.11 2.062 52.37 .165 4.19 .500 12.70 2.125 53.98 .1

4、87 4.75 .609 15.47 3.156 80.16 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information. 3. Unless otherwise specified, tolerance is .010 (.25 mm). 4. After assembly, the eccentricity between the end of the shank and the tip of the plug shall not exceed .008 (.20 mm) TIR (

5、total indicator reading). 5. Thread shall be in accordance with FED-STD-H28, and there shall be sufficient length of thread on the shell to assure a minimum thread engagement of four full threads between the shell and the body of the plug after assembled. When the plug shell and body are assembled,

6、the shell shall not protrude beyond the shoulder of the plug. FIGURE 1. Dimensions and configuration - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-642/5C 3 Inch/mm conversion chart Inches mm .031 .787 .063 1.6 .156 3.96 .188 4.

7、76 .969 24.61 NOTES: 1. Material shall be steel, as rolled, condition no. 3 quarter hard temper, regular bright finish, in accordance with QQ-S-698. 2. Finish shall be cadmium plate in accordance with SAE-AMS-QQ-P-416, type II, class C, or zinc coat, .0002 inch thick, with chromate treatment, in acc

8、ordance with ASTM B633. 3. Remove all burrs and sharp edges. FIGURE 2. Collar, cable. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-642/5C 4 REQUIREMENTS Dimensions and configurations: See figures 1 and 2. Shell: Shall be black plastic in a

9、ccordance with MIL-DTL-642. Terminal screws: Shall be .086-64 UNF-2A in accordance with MIL-P-642/12. One cable clamp, as shown on figure 2, shall be supplied with each plug. Part or Identifying Number (PIN): M642/5-1. The margins of this specification are marked with vertical lines to indicate wher

10、e changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of

11、 the marginal notations and relationship to the last previous issue. Referenced documents. In addition to MIL-P-642, this document references the following: MIL-P-642/12 QQ-S-698 FED-STD-H28 ASTM-B633 SAE-AMS-QQ-P-416 CONCLUDING MATERIAL Custodians: Preparing activity: Army - CR DLA - CC Navy - EC A

12、ir Force 85 (Project 5935-2013-167) DLA - CC Review activities: Army - AR, CR4, MI Navy - AS, MC, OS, SH NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-