DLA MIL-DTL-55302 193 B-2009 CONNECTORS PRINTED CIRCUIT SUBASSEMBLY AND ACCESSORIES PLUG PIN CONTACTS 122 AND 152 POSITION PRINTED WIRING BOARD ( 075 SPACING).pdf

《DLA MIL-DTL-55302 193 B-2009 CONNECTORS PRINTED CIRCUIT SUBASSEMBLY AND ACCESSORIES PLUG PIN CONTACTS 122 AND 152 POSITION PRINTED WIRING BOARD ( 075 SPACING).pdf》由会员分享，可在线阅读，更多相关《DLA MIL-DTL-55302 193 B-2009 CONNECTORS PRINTED CIRCUIT SUBASSEMBLY AND ACCESSORIES PLUG PIN CONTACTS 122 AND 152 POSITION PRINTED WIRING BOARD ( 075 SPACING).pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、 INCH-POUND MIL-DTL-55302/193B 10 February 2009 SUPERSEDING MIL-DTL-55302/193A 20 January 2006 DETAIL SPECIFICATION SHEET CONNECTORS, PRINTED CIRCUIT SUBASSEMBLY AND ACCESSORIES: PLUG, PIN CONTACTS, 122 AND 152 POSITION, PRINTED WIRING BOARD (.075 SPACING) This specification is approved for use by a

2、ll Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-55302. FIGURE 1. Connector, plug, .075 (1.91 mm) spacing. AMSC N/A FSC 5935 Provided by IHSNot for ResaleNo reproduction or netw

3、orking permitted without license from IHS-,-,-MIL-DTL-55302/193B 2 FIGURE 1. Connector, plug, .075 (1.91 mm) spacing - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-55302/193B 3 FIGURE 1. Connector, plug, .075 (1.91 mm) spacing -

4、 Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-55302/193B 4 FIGURE 1. Connector, plug, .075 (1.91 mm) spacing - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-

5、55302/193B 5 Dimensions Number of contacts A .010 BSC B BSC C BSC D E .010 BSC F 122 3.440 (87.38) 3.250 (82.6) 2.925 (74.30) 3.610 (91.69) 3.780 (96.01) 3.000 (76.20) 152 4.190 (106.43) 4.000 (101.6) 3.675 (93.35) 4.360 (110.74) 4.530 (115.06) 3.750 (95.25) Inches mm Inches mm Inches mm .001 0.03 .

6、0375 0.95 .150 3.81 .002 0.05 .060 1.52 .156 3.96 .005 0.13 .078 1.98 .172 4.37 .006 0.15 .080 2.03 .200 5.08 .008 0.20 .082 2.08 .300 7.62 .010 0.25 .086 2.18 .390 9.91 .014 0.36 .100 2.54 .490 12.45 .020 0.51 .109 2.77 .545 13.84 .0245 0.62 .110 2.79 .700 17.78 .0255 0.66 .125 3.18 .028 0.71 .135

7、3.43 .031 0.79 .140 3.56 .032 0.81 .141 3.56 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Unless otherwise specified, tolerances are +.005 (0.13 mm). 4. These connectors mate with connectors specified in MIL-DTL-55302/192 using appropriate hardware. 5.

8、 Numbers indicating the first and last position in each row and every fourth contact position in between shall be marked on the side(s) of the connector. As an option to the above, numbers indicating every fourth cavity may be stamped on the side of the connector, with exception that the number one

9、contact shall be marked. FIGURE 1. Connector, plug, .075 (1.91 mm) spacing - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-55302/193B 6 REQUIREMENTS Dimensions and configuration: See figure 1. Material: Guide pins, type X guide s

10、ockets, jackscrews, and jacksockets shall be made of corrosion resisting stainless steel in accordance with ASTM A581/A581M or ASTM A582/A582M, passivated in accordance with SAE-AMS-2700, or shall be corrosion resistant copper nickel alloy (61 2 percent copper, 25 2 percent nickel, 2.5 percent maxim

11、um other, and the balance zinc) and shall have a brinell hardness of 145 to 175. Type Y guide sockets shall be beryllium copper in accordance with ASTM B196/B196M or ASTM B197/B197M, nickel plated in accordance with MIL-DTL-38999, appendix A, class 02, 50 to 150 microinches. Plating: The contact pla

12、ting shall be in accordance with MIL-DTL-55302, or gold in accordance with ASTM B488, type II, code C, class 1.27, over nickel plating in accordance with MIL-DTL-38999, appendix A, class 02, 50 to 150 microinches in the engaging area and gold in accordance with ASTM B488, type II, code C, class 0.51

13、 or type III, code A class 0.51, over nickel plating in accordance with MIL-DTL-38999, appendix A, class 02, 50 to 150 microinches in the termination area. Contact identification: See figure 1. Jackscrews and jacksocket torque: 2 inch pounds max fully mated. Contact resistance: The average contact r

14、esistance of all contacts measured shall not exceed 0.007 ohm, and no individual contact pair shall have a resistance exceeding 0.015 ohm. Dielectric withstanding voltage: Sea level: 750 volts rms. High altitude: 250 volts rms at 70,000 feet. Current rating: 3.0 amperes maximum per contact. Polariza

15、tion: Type X regular, guide pin and socket, full round (see figure 1). Type Y, adjustable “D” shaped guide pin and socket (see figure 1, detail A). All connectors are supplied in the -1 polarized position. For other than OEM use, connectors may be repolarized by using M55302/57-01 spanner wrench and

16、 M55302/190-01 guide pin and guide socket kit. When guides are removed and reinstalled in another position, apply Loctite 83-CV or equivalent on the threads. Ordering connectors in other than the -1 polarized position may be done by the OEMs by placing the desired polarized position in brackets thre

17、e spaces after the Part or Identifying Number (PIN) on the purchase order. Example: M55302/193A122Y -32. Polarization pins and sockets shall be adjusted to any desired configuration by spanner wrench (M55302/57-01). Ordering connectors in the -1 polarized position without Loctite 83-CV or equivalent

18、 applied may be done by placing a “-0” in brackets three spaces after the PIN on the purchase order. Guide sets, as installed, shall withstand 7 ounce-inches backoff torque applied through the guide set mounting nut. M55302/190-01 kit: Consists of one type Y ”D” shaped guide socket and one type Y “D

19、” shaped guide pin and two spanner nuts. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-55302/193B 7 Example of Part or Identifying Number (PIN): M55302/193 A 122 X Basic number of specification sheet Type of terminals (see figure 1) A = dip

20、 terminal .109 long B = dip terminal .140 long C = dip terminal .172 long Number of contacts (see figure 1) Type of mounting hardware (see figure 1) Type X = full round Type Y = “D” shaped Type F = fixed jackset Type S = short turning hex jackset Type N = turning hex jackset Type L = turning slotted

21、 jackset Type M = short turning slotted jackset Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-55302/193B 8 Changes from previous issue. The margins of this specification are marked with vertical lines to indicate where changes from the prev

22、ious issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations

23、 and relationship to the last previous issue. Referenced documents. In addition to MIL-DTL-55302, this document references the following: MIL-DTL-38999 MIL-DTL-55302/192 ASTM A581/A581M ASTM A582/A582M ASTM B196/B196M ASTM B197/B197M ASTM B488 SAE-AMS-2700 CONCLUDING MATERIAL Custodians: Preparing a

24、ctivity: Army - CR DLA - CC Navy - EC Air Force 85 DLA - CC (Project: 5935-2008-026) Review activities: Army - AR, AT, AV, CR4, MI Navy - AS, MC, OS, SH Air Force - 19, 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil . Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-