DLA MIL-DTL-55302 190 B-2011 CONNECTORS PRINTED CIRCUIT SUBASSEMBLY AND ACCESSORIES RECEPTACLE SOCKET CONTACTS DECADE INCREMENTS 10 THRU 100 POSITIONS PRINTED WIRING BOARD ( 075 SP.pdf

《DLA MIL-DTL-55302 190 B-2011 CONNECTORS PRINTED CIRCUIT SUBASSEMBLY AND ACCESSORIES RECEPTACLE SOCKET CONTACTS DECADE INCREMENTS 10 THRU 100 POSITIONS PRINTED WIRING BOARD ( 075 SP.pdf》由会员分享，可在线阅读，更多相关《DLA MIL-DTL-55302 190 B-2011 CONNECTORS PRINTED CIRCUIT SUBASSEMBLY AND ACCESSORIES RECEPTACLE SOCKET CONTACTS DECADE INCREMENTS 10 THRU 100 POSITIONS PRINTED WIRING BOARD ( 075 SP.pdf（9页珍藏版）》请在麦多课文档分享上搜索。

1、AMSC N/A FSC 5935 MIL-DTL-55302/190B 21 March 2011 SUPERSEDING MIL-DTL-55302/190A 20 January 2006 DETAIL SPECIFICATION SHEET CONNECTORS, PRINTED CIRCUIT SUBASSEMBLY AND ACCESSORIES: RECEPTACLE, SOCKET CONTACTS, DECADE INCREMENTS 10 THRU 100 POSITIONS, PRINTED WIRING BOARD (.075 SPACING) This specifi

2、cation is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-55302. FIGURE 1. Connector, receptacle, .075 (1.91 mm) spacing. INCH-POUND Provided by IHSNot for

3、 ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-55302/190B 2 WIRE WRAP TERMINAL DETAIL C FIGURE 1. Connector, receptacle, .075 (1.91 mm) spacing - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-

4、55302/190B 3 FIGURE 1. Connector, receptacle, .075 (1.91 mm) spacing - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-55302/190B 4 FIGURE 1. Connector, receptacle, .075 (1.91 mm) spacing - Continued. Provided by IHSNot for ResaleN

5、o reproduction or networking permitted without license from IHS-,-,-MIL-DTL-55302/190B 5 Number of contacts Dimensions A .010 BSC B BSC C BSC D E .010 10 .798 (20.27) .618 (15.70) 0.300 (7.62) .968 (24.59) 1.138 (28.91) 20 1.173 (29.79) .993 (25.22) 0.675 (17.15) 1.343 (34.11) 1.513 (38.43) 30 1.548

6、 (39.32) 1.368 (34.75) 1.050 (26.67) 1.718 (43.64) 1.888 (47.96) 40 1.923 (48.84) 1.743 (44.27) 1.425 (36.20) 2.093 (53.16) 2.263 (57.48) 50 2.298 (58.37) 2.118 (53.80) 1.800 (45.72) 2.468 (62.69) 2.638 (67.01) 60 2.673 (67.89) 2.493 (63.32) 2.175 (55.25) 2.843 (72.21) 3.013 (76.53) 70 3.048 (77.42)

7、 2.868 (72.85) 2.550 (64.77) 3.218 (81.74) 3.388 (86.06) 80 3.423 (86.94) 3.243 (82.37) 2.925 (74.30) 3.593 (91.26) 3.763 (95.58) 90 3.798 (96.47) 3.618 (91.90) 3.300 (83.82) 3.968 (100.79) 4.138 (105.11) 100 4.173 (105.99) 3.993 (101.42) 3.675 (93.35) 4.343 (110.31) 4.513 (114.63) Inches mm Inches

8、mm Inches mm .001 0.03 .0375 0.95 .160 4.06 .005 0.13 .0625 1.59 .170 4.32 .006 0.15 .075 1.91 .172 4.37 .008 0.20 .078 1.98 .200 5.08 .010 0.25 .080 2.03 .300 7.62 .014 0.36 .082 2.08 .315 8.00 .017 0.43 .086 2.18 .375 9.53 .018 0.46 .093 2.36 .400 10.16 .020 0.51 .100 2.54 .490 12.45 .0245 0.62 .1

9、09 2.77 .500 12.70 .0255 0.65 .110 2.79 .545 13.84 .028 0.71 .125 3.18 .625 15.88 .030 0.76 .140 3.56 .700 17.78 .031 0.79 .141 3.58 .032 0.81 .156 3.96 FIGURE 1. Connector, receptacle, .075 (1.91 mm) spacing - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without l

10、icense from IHS-,-,-MIL-DTL-55302/190B 6 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Unless otherwise specified, tolerances are +.005 (0.13 mm). 4. These connectors mate with connectors specified in MIL-DTL-55302/191 using appropriate hardware. 5. Num

11、bers indicating the first and last position in each row and every fourth contact in between shall be marked on the side(s) of the connector. As an option to the above, numbers indicating every fourth cavity may be stamped on the side of the connector, with exception that the number one contact shall

12、 be marked. 6. Conformal coating cleanness shall be .005 (0.13 mm) minimum. FIGURE 1. Connector, receptacle, .075 (1.91 mm) spacing - Continued. REQUIREMENTS Dimensions and configuration: See figure 1. Material: Guide pins, type X guide sockets, jackscrews, and jacksockets shall be made of corrosion

13、 resisting stainless steel in accordance with ASTM A581/A581M or ASTM A582/A582M, passivated in accordance with SAE-AMS-2700, or shall be corrosion resistant copper nickel alloy (61 2 percent copper, 25 2 percent nickel, 2.5 percent maximum other, and the balance zinc) and shall have a brinell hardn

14、ess of 145 to 175. Type Y guide sockets shall be beryllium copper in accordance with ASTM B196/B196M or ASTM B197/B197M, nickel plated in accordance with SAE-AMS-QQ-N-290, class 02, 50 to 150 microinches. Plating: The contact plating shall be in accordance with MIL-DTL-55302, or gold in accordance w

15、ith ASTM B488, type II, code C, class 1.27, over nickel plating in accordance with SAE-AMS-QQ-N-290, class 02, 50 to 150 microinches in the engaging area and gold in accordance with ASTM B488, type III, code C, class 0.51 or type II, code A class 0.51, over nickel plating in accordance with SAE-AMS-

16、QQ-N-290, class 02, 50 to 150 microinches in the termination area. Contact identification: See figure 1. Oversize pin exclusion: In accordance with MIL-DTL-55302, except that the test for contact size number 23 shall be performed. Contact engagement and separation forces (number 24 contacts): Minimu

17、m separation: 0.5 ounce with 0.0245 inch diameter test pin, reference SAE-AS31971-24X1. Maximum engagement: 4.0 ounces with 0.0255 inch diameter test pin, reference SAE-AS31971-24Y1. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-55302/190B

18、7 Mating and unmating: Low insertion force contacts: The maximum mating force, in pounds, shall be the number of contacts multiplied by 0.25 and the withdrawal force, in pounds, shall be a minimum of 0.04 times the number of contacts and shall not exceed the measured insertion force. NOTE: Not appli

19、cable when mating and unmating is accomplished through the engaging of jackscrews and jacksockets. Jackscrews and jacksocket torque: 2 inch pounds max fully mated. Contact resistance: The average contact resistance of all contacts measured shall not exceed 0.007 ohm, and no individual contact pair s

20、hall have a resistance exceeding 0.015 ohm. Dielectric withstanding voltage: Sea level: 750 volts rms. High altitude: 250 volts rms at 70,000 feet. Current rating: 3.0 amperes maximum per contact. Polarization: Type X regular, guide pin and socket, full round (see figure 1). Type Y, adjustable “D” s

21、haped guide pin and socket (see figure 1, detail D). All connectors are supplied in the -1 polarized position. For other than OEM use, connectors may be repolarized by using M55302/57-01 spanner wrench and M55302/190-01 guide pin and guide socket kit. When guides are removed and reinstalled in anoth

22、er position, apply Loctite 83-CV or equivalent on the threads. Ordering connectors in other than the -1 polarized position may be done by the OEMs by placing the desired polarized position in brackets three spaces after the part or Identifying Number (PIN) on the purchase order. Example: M55302/57-A

23、10Y -32. Polarization pins and sockets shall be adjusted to any desired configuration by spanner wrench (M55302/57-01). Ordering connectors in the -1 polarized position without Loctite 83-CV or equivalent applied may be done by placing a “-0” in brackets three spaces after the PIN on the purchase or

24、der. Guide sets, as installed, shall withstand 7 ounce-inches backoff torque applied through the guide set mounting nut. M55302/190-01 kit: Consists of one type Y ”D” shaped guide socket and one type Y “D” shaped guide pin and two spanner nuts. Provided by IHSNot for ResaleNo reproduction or network

25、ing permitted without license from IHS-,-,-MIL-DTL-55302/190B 8 Example of PIN: M55302/190 L A 100 Y Basic number of specification sheet Type of contacts L = low insertion force contacts Type of terminals (see figure 1) A = solder cup B = dip terminal .109 long C = dip terminal .140 long D = dip ter

26、minal .172 long E = .093 flexible circuit F = wire wrap .375 long G = wire wrap .500 long H = wire wrap .625 long Number of contacts (see figure 1) Type of mounting hardware (see figure 1) Type X = full round Type Y = “D” shaped Type F = fixed jackset Type S = short turning hex jackset Type N = turn

27、ing hex jackset Type L = turning sloted jackset Type M = short turning slotted jackset Changes from previous issue. The margins of this specification are marked with vertical lines to indicate where changes from the previous issue were made. This was done as a convenience only and the Government ass

28、umes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Referenced documents. In addition

29、to MIL-DTL-55302, this document references the following: MIL-DTL-55302/191 ASTM A581/A581M ASTM A582/A582M ASTM B196/B196M ASTM B197/B197M ASTM B488 SAE-AMS-QQ-N-290 SAE-AMS-2700 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-55302/190B 9 C

30、ONCLUDING MATERIAL Custodians: Preparing activity: Army - CR DLA - CC Navy EC- Air Force 85 DLA - CC (Project 5935-2010-147) Review activities: Army - AR, AT, AV, CR4, MI Navy - AS, MC, OS, SH Air Force - 19, 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil/ . Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-