DLA MIL-DTL-55302 168 C-2010 CONNECTORS PRINTED CIRCUIT SUBASSEMBLY AND ACCESSORIES LOW MATING FORCE MALE BRUSH RIGHT ANGLE POLARIZED FOR MULTILAYERED PRINTED WIRING BOARDS ( 100 S.pdf

《DLA MIL-DTL-55302 168 C-2010 CONNECTORS PRINTED CIRCUIT SUBASSEMBLY AND ACCESSORIES LOW MATING FORCE MALE BRUSH RIGHT ANGLE POLARIZED FOR MULTILAYERED PRINTED WIRING BOARDS ( 100 S.pdf》由会员分享，可在线阅读，更多相关《DLA MIL-DTL-55302 168 C-2010 CONNECTORS PRINTED CIRCUIT SUBASSEMBLY AND ACCESSORIES LOW MATING FORCE MALE BRUSH RIGHT ANGLE POLARIZED FOR MULTILAYERED PRINTED WIRING BOARDS ( 100 S.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、AMSC N/A FSC 5935 MIL-DTL-55302/168C 21 January 2010 SUPERSEDING MIL-DTL-55302/168B 13 May 2005 DETAIL SPECIFICATION SHEET CONNECTORS, PRINTED CIRCUIT SUBASSEMBLY AND ACCESSORIES: LOW MATING FORCE, MALE BRUSH, RIGHT ANGLE, POLARIZED, FOR MULTILAYERED PRINTED WIRING BOARDS (.100 SPACING) This specifi

2、cation is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-55302. FIGURE 1. Connector, printed circuit, male brush, right angle for multilayered printed wir

3、ing boards .100 (2.54 mm) spacing. INCH-POUND Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-55302/168C 2 Inches mm Inches mm Inches mm Inches mm .002 0.05 .020 0.51 .129 3.28 .330 8.38 .004 0.10 .021 0.53 .185 4.70 .365 9.27 .005 0.13 .100

4、2.54 .193 4.90 .390 9.91 .007 0.18 .112 2.84 .200 5.08 .430 10.92 .010 0.25 .120 3.04 .230 5.84 .490 12.45 .012 0.30 .126 3.20 .300 7.62 .590 14.99 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Unless otherwise specified, tolerance is .010 (0.25 mm). 4.

5、 These connectors mate with connectors specified in MIL-DTL-55302/169 and MIL-DTL-55302/170 and are primarily for use with single-sided, double-sided, or multilayered printed wiring boards. 5. The polarization feature, utilizing four M55302/78-02 polarizing keys which are not supplied with the conne

6、ctor, will provide 256 unique polarizing positions. 6. For dimensions A through K, see table I. 7. Coupling/mounting bushings are not supplied with the connector. See M55302/172-05. 8. Contact rows are identified by molded letters on the front and rear face. Numbers indicating every fifth contact pe

7、r row appear on rear face, except for arrangements consisting of 10 contacts per row which lack numerals. Up to 9 contact locations at the high numeral end of the contact row will not be identified. 9. Perfect form at MMC not required. Dimension for user installation purposes only. 10. Part or Ident

8、ifying Number (PIN). FIGURE 1. Connector, printed circuit, male brush, right angle multilayered printed wiring boards .100 (2.54 mm) spacing Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-55302/168C 3 Inches mm .100 2.54 .200 5.08

9、 .5375 13.652 NOTE: The arrangement length is determined by (N-1) x.100, where N is the number of contacts per row. Example: For 60 contact row would be (60-1) x.100 = 5.90 inches. FIGURE 2. Insert arrangement for .100 (2.54 mm) contact spacing, male brush connectors (engaging face). Provided by IHS

10、Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-55302/168C 4 REQUIREMENTS Dimensions and configurations: See figure 1 and tables I and II. Contacts: Each contact shall contain 7 brush wires with a tolerance limit of 1. Each brush wire diameter shall be .007

11、3 to .0085 inch (0.185 mm to 0.216 mm). Material: Body: Glass filled thermoplastic molding material in accordance with ASTM D5948, type GPT-15F. Contacts: In accordance with MIL-DTL-55302, ASTM B187/B187M or ASTM B272. Plating: The contact termination plating shall be specified in table III. Brush w

12、ire plating shall be gold in accordance with ASTM B488, type II, code C, class 1.27 over nickel in accordance with MIL-DTL-38999, Appendix A. Cut ends or brush wires need not be plated. Contact identification: See figure 1 (note 8) and figure 2. Oversized pin exclusion: Not applicable. Contact engag

13、ement and separation forces: Not applicable, see mating and unmating. Mating and unmating: The maximum mating and unmating force shall be 1.5 ounces times the total number of contacts. Contact current rating: The connector may have any combination of current flow and ambient temperature provided the

14、 contact or connector temperature does not exceed 125C. The test current shall be 5 amperes for individually connected contacts and 3 amperes for series wired contacts. Contact resistance: The average resistance of all contact pairs measured on row A contacts shall not exceed 0.016 ohm, and no indiv

15、idual pair shall have a resistance exceeding 0.020 ohm. To allow for increased terminal lengths, add 0.001 ohm for each contact row beyond row A. The point of measurement shall be the point of terminal exit from the printed wiring board. Contact retention: 3 pounds per contact minimum when the force

16、 is applied in the forward direction. The displacement shall not exceed 0.005 (0.13 mm). The displacement shall be recorded after a 1 pound preload is used to determine the zero displacement reference. Dielectric withstanding voltage: Sea level: 1,300 volts rms, 60 Hz, ac. High altitude: 325 volts r

17、ms, 60 Hz, ac. Extended contact life: Connector shall meet the performance requirements of MIL-DTL-55302, contact life, when subjected to 20,000 insertion and withdrawal cycles during qualification inspection. Insert arrangement: See figure 2. Provided by IHSNot for ResaleNo reproduction or networki

18、ng permitted without license from IHS-,-,-MIL-DTL-55302/168C 5 PIN: Consists of the letter M, the basic number of the specification sheet, and a dash number compiled as follows: Example: M55302/168 B 18 Y 2 Specification sheet number Number of rows (indicator) (see table I for row indicator) Number

19、of contacts per row (see table I for contact indicator) Contact tail termination length (see table II for indicator) Gold plated contact tails (see table III for indicator) User instructions: Each shipment of connectors shall include, as a minimum, instructions for coupling/mounting bushing usage, p

20、olarization key usage and electrical probing information. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-55302/168C 6 TABLE I. Indicators and dimensions. 2 Contact rows 3 Contact rows 4 Contact rows Dimensions 1/ 2/ Indicator 3/ Total contac

21、ts Indicator 3/ Total contacts Indicator 3/ Total contacts A Max B + .004 K - .006 A10 20 B10 30 C10 40 2.295 (58.29) 1.975 (50.17) 1.115 (28.32) A11 22 B11 33 C11 44 2.396 (60.86) 2.075 (52.71) 1.215 (30.86) A12 24 B12 36 C12 48 2.495 (63.37) 2.175 (55.25) 1.315 (33.40) A13 26 B13 39 C13 52 2.595 (

22、65.91) 2.275 (57.79) 1.415 (35.94) A14 28 B14 42 C14 56 2.695 (68.45) 2.375 (60.33) 1.515 (38.48) A15 30 B15 45 C15 60 2.795 (70.99) 2.475 (62.87) 1.615 (41.02) A16 32 B16 48 C16 64 2.895 (73.53) 2.575 (65.41) 1.715 (43.56) A17 34 B17 51 C17 68 2.995 (76.07) 2.675 (67.95) 1.815 (46.10) A18 36 B18 54

23、 C18 72 3.095 (78.61) 2.775 (70.49) 1.915 (48.64) A19 38 B19 57 C19 76 3.195 (81.15) 2.875 (73.03) 2.015 (51.18) A20 40 B20 60 C20 80 3.295 (83.69) 2.975 (75.57) 2.115 (53.72) A21 42 B21 63 C21 84 3.395 (86.23) 3.075 (78.11) 2.215 (56.26) A22 44 B22 66 C22 88 3.495 (88.77) 3.175 (80.65) 2.315 (58.80

24、) A23 46 B23 69 C23 92 3.595 (91.31) 3.275 (83.19) 2.415 (61.34) A24 48 B24 72 C24 96 3.695 (93.85) 3.375 (85.73) 2.515 (63.88) A25 50 B25 75 C25 100 3.795 (96.39) 3.475 (88.27) 2.615 (66.42) A26 52 B26 78 C26 104 3.895 (98.93) 3.575 (90.81) 2.715 (68.96) A27 54 B27 81 C27 108 3.995 (101.47) 3.675 (

25、93.35) 2.815 (71.50) A28 56 B28 84 C28 112 4.095 (104.01) 3.775 (95.89) 2.915 (74.04) A29 58 B29 87 C29 116 4.195 (106.55) 3.875 (98.43) 3.015 (76.58) A30 60 B30 90 C30 120 4.295 (109.09) 3.975 (100.97) 3.115 (79.12) A31 62 B31 93 C31 124 4.395 (111.63) 4.075 (103.51) 3.215 (81.66) A32 64 B32 96 C32

26、 128 4.495 (114.17) 4.175 (106.05) 3.315 (84.20) A33 66 B33 99 C33 132 4.595 (116.71) 4.275 (108.59) 3.415 (86.74) A34 68 B34 102 C34 136 4.695 (119.25) 4.375 (111.13) 3.515 (89.28) A35 70 B35 105 C35 140 4.795 (121.79) 4.475 (113.67) 3.615 (91.82) A36 72 B36 108 C36 144 4.895 (124.33) 4.575 (116.21

27、) 3.715 (94.36) A37 74 B37 111 C37 148 4.995 (126.87) 4.675 (118.75) 3.815 (96.90) A38 76 B38 114 C38 152 5.095 (129.41) 4.775 (121.29) 3.915 (99.44) See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-55302/168C 7

28、TABLE I. Indicators and dimensions Continued. 2 Contact rows 3 Contact rows 4 Contact rows Dimensions 1/ 2/ Indicator 3/ Total contacts Indicator 3/ Total contacts Indicator 3/ Total contacts A Max B + .004 K - .006 A39 78 B39 117 C39 156 5.195 (131.95) 4.875 (123.83) 4.015 (101.98) A40 80 B40 120 C

29、40 160 5.295 (134.49) 4.975 (126.37) 4.115 (104.52) A42 82 B41 123 C41 164 5.395 (137.03) 5.075 (128.91) 4.215 (107.06) A42 84 B42 126 C42 168 5.495 (139.57) 5.175 (131.45) 4.315 (109.60) A43 86 B43 129 C43 172 5.595 (142.11) 5.275 (133.99) 4.415 (112.14) A44 88 B44 132 C44 176 5.695 (144.65) 5.375

30、(136.53) 4.515 (114.68) A45 90 B45 135 C45 180 5.795 (147.19) 5.475 (139.07) 4.615 (117.22) A46 92 B46 138 C46 184 5.895 (149.73) 5.575 (141.61) 4.715 (119.76) A47 94 B47 141 C47 188 5.995 (152.27) 5.675 (144.15) 4.815 (122.30) A48 96 B48 144 C48 192 6.095 (154.81) 5.775 (146.69) 4.915 (124.84) A49

31、98 B49 147 C49 196 6.195 (157.35) 5.875 (149.23) 5.015 (127.38) A50 100 B50 150 C50 200 6.295 (159.89) 5.975 (151.77) 5.115 (129.92) A51 102 B51 153 C51 204 6.395 (162.43) 6.075 (154.31) 5.215 (132.46) A52 104 B52 156 C52 208 6.495 (164.97) 6.175 (156.85) 5.315 (135.00) A53 106 B53 159 C53 212 6.595

32、 (167.51) 6.275 (159.39) 5.415 (137.54) A54 108 B54 162 C54 216 6.695 (170.05) 6.375 (161.93) 5.515 (140.08) A55 110 B55 165 C55 220 6.795 (172.59) 6.475 (164.47) 5.615 (142.62) A56 112 B56 168 C56 224 6.895 (175.13) 6.575 (167.01) 5.715 (145.16) A57 114 B57 171 C57 228 6.995 (177.67) 6.675 (169.55)

33、 5.815 (147.70) A58 116 B58 174 C58 232 7.095 (180.21) 6.775 (172.09) 5.915 (150.24) A59 118 B59 177 C59 236 7.195 (182.75) 6.875 (174.63) 6.015 (152.78) A60 120 B60 180 C60 240 7.295 (185.29) 6.975 (177.17) 6.115 (155.32) A61 122 B61 183 C61 244 7.395 (187.83) 7.075 (179.71) 6.215 (157.86) A62 124

34、B62 186 C62 248 7.495 (190.37) 7.175 (182.25) 6.315 (160.40) A63 126 B63 189 C63 252 7.595 (192.91) 7.275 (184.79) 6.415 (162.94) A64 128 B64 192 C64 256 7.695 (195.45) 7.375 (187.33) 6.515 (165.48) A65 130 B65 195 C65 260 7.795 (197.99) 7.475 (189.87) 6.615 (168.02) A66 132 B66 198 C66 264 7.895 (2

35、00.53) 7.575 (192.41) 6.715 (170.56) See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-55302/168C 8 TABLE I. Indicators and dimensions Continued. 2 Contact rows 3 Contact rows 4 Contact rows Dimensions 1/ 2/ Indic

36、ator 3/ Total contacts Indicator 3/ Total contacts Indicator 3/ Total contacts A Max B + .004 K - .006 A67 134 B67 201 C67 268 7.995 (203.07) 7.675 (194.95) 6.815 (173.10) A68 136 B68 204 C68 272 8.095 (205.61) 7.775 (197.49) 6.915 (175.64) A69 138 B69 207 C69 276 8.195 (208.15) 7.875 (200.03) 7.015

37、 (178.18) A70 140 B70 210 C70 280 8.295 (210.69) 7.975 (202.57) 7.115 (180.72) A71 142 B71 213 C71 284 8.395 (213.23) 8.075 (205.11) 7.215 (183.26) A72 144 B72 216 C72 288 8.495 (215.77) 8.175 (207.65) 7.315 (185.80) A73 146 B73 219 C73 292 8.595 (218.31) 8.275 (210.19) 7.415 (188.34) A74 148 B74 22

38、2 C74 296 8.695 (220.85) 8.375 (212.73) 7.515 (190.88) A75 150 B75 225 C75 300 8.795 (223.39) 8.475 (215.27) 7.615 (193.42) A76 152 B76 228 C76 304 8.895 (225.93) 8.575 (217.81) 7.715 (195.96) A77 154 B77 231 C77 308 8.995 (228.47) 8.675 (220.35) 7.815 (198.50) A78 156 B78 234 C78 312 9.095 (223.10)

39、 8.775 (222.89) 7.915 (201.04) A79 158 B79 237 C79 316 9.195 (233.55) 8.875 (225.43) 8.015 (203.58) A80 160 B80 240 C80 320 9.295 (236.09) 8.975 (227.97) 8.115 (206.12) A81 162 B81 243 C81 324 9.395 (238.63) 9.075 (230.51) 8.215 (208.66) A82 164 B82 246 C82 328 9.495 (241.17) 9.175 (233.05) 8.315 (2

40、11.20) A83 166 B83 249 C83 332 9.595 (243.71) 9.275 (235.59) 8.415 (213.74) A84 168 B84 252 C84 336 9.695 (246.25) 9.375 (238.13) 8.515 (216.28) A85 170 B85 255 C85 340 9.795 (248.79) 9.475 (240.67) 8.615 (218.82) See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or network

41、ing permitted without license from IHS-,-,-MIL-DTL-55302/168C 9 TABLE I. Indicators and dimensions - Continued. 2 Contact rows 3 Contact rows 4 Contact rows Dimensions 1/ 2/ Indicator 3/ Total contacts Indicator 3/ Total contacts Indicator 3/ Total contacts A Max B + .004 K - .006 A86 172 B86 258 C8

42、6 344 9.895 (251.33) 9.575 (243.21) 8.715 (221.36) A87 174 B87 261 C87 348 9.995 (253.87) 9.675 (245.75) 8.815 (223.90) A88 176 B88 264 C88 352 10.095 (256.41) 9.775 (248.29) 8.915 (226.44) A89 178 B89 267 C89 356 10.195 (258.95) 9.875 (250.83) 9.015 (228.98) A90 180 B90 270 C90 360 10.295 (261.49)

43、9.975 (253.37) 9.115 (231.53) A91 182 B91 273 C91 364 10.395 (264.03) 10.075 (255.91) 9.215 (234.06) A92 184 B92 276 C92 368 10.495 (266.57) 10.175 (258.45) 9.315 (236.60) A93 186 B93 279 C93 372 10.595 (269.11) 10.275 (260.99) 9.415 (239.14) A94 188 B94 282 C94 376 10.695 (271.65) 10.375 (263.53) 9

44、.515 (241.68) A95 190 B95 285 C95 380 10.795 (274.19) 10.475 (266.07) 9.615 (244.22) A96 192 B96 288 C96 384 10.895 (276.73) 10.575 (268.61) 9.715 (246.76) A97 194 B97 291 C97 388 10.995 (279.27) 10.675 (271.15) 9.815 (249.30) A98 196 B98 294 C98 392 11.095 (281.81) 10.775 (273.69) 9.915 (251.84) A9

45、9 198 B99 297 C99 396 11.195 (284.35) 10.875 (276.23) 10.015 (254.38) A00 200 B00 300 C00 400 11.295 (286.89) 10.975 (278.77) 10.115 (256.92) 1/ All dimensions are in inches. 2/ Metric equivalents are given for information only. 3/ Indicators consist of, a letter designating number of contact rows a

46、nd two digits indicating number of contacts per row. Indicators A00, B00, and C00 denotes 100 contacts per row. TABLE II. Contact tail termination length. Indicator T dimension Z .095 + .035 - .025 Y .150 + .035 - .025 Provided by IHSNot for ResaleNo reproduction or networking permitted without lice

47、nse from IHS-,-,-MIL-DTL-55302/168C 10 TABLE III. Contact tail plating. Indicator Plating 1 Tin lead in accordance with SAE-AMS-P-81728, 50 to 70 percent tin, .0001 minimum thick over copper plating in accordance with SAE-AMS2418 2 Gold in accordance with ASTM B488, type II, code C, class 0.51 over

48、nickel in accordance with MIL-DTL-38999, appendix A CHANGES FROM PREVIOUS ISSUE: The margins of this specification are marked with vertical lines to indicate where changes from previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Referenced documents. In