DLA MIL-DTL-3922 54 E-2013 FLANGES WAVEGUIDE (COVER) (SQUARE 4 HOLE).pdf

《DLA MIL-DTL-3922 54 E-2013 FLANGES WAVEGUIDE (COVER) (SQUARE 4 HOLE).pdf》由会员分享，可在线阅读，更多相关《DLA MIL-DTL-3922 54 E-2013 FLANGES WAVEGUIDE (COVER) (SQUARE 4 HOLE).pdf（7页珍藏版）》请在麦多课文档分享上搜索。

1、AMSC N/A FSC 5985 MIL-DTL-3922/54E 23 July 2013 SUPERSEDING MIL-DTL-3922/54D 23 May 2008 DETAIL SPECIFICATION SHEET FLANGES, WAVEGUIDE (COVER) (SQUARE, 4 HOLE) This specification is approved for use by all Departments and Agencies of the Department of Defense. Requirements for acquiring the flanges

2、described herein shall consist of this document and MIL-DTL-3922. NOTES: 1. Dimensions are in inches. Dimensions are in accordance with ASME-Y14.5M. 2. Millimeter equivalents (to the nearest 0.01 mm) are given for general information only and are based upon 1.00 inch = 25.4 mm. 3. Millimeters are in

3、 table. 4. These surfaces to be parallel within .0005 (0.01 mm) to facilitate the use of quick disconnect couplings. 5. Roughness of mating surfaces shall not exceed 63 micro-inches in accordance with ASME-B46.1, except that flaws shall be included in the roughness height measurement. 6. These surfa

4、ces to be parallel within .002 for PIN M3922/54-003 only. FIGURE 1. Flange configuration (-001 through -004). INCH-POUND Inches mm .001 .002 .016 .046 .116 0.02 0.05 0.41 1.17 2.95 INACTIVE FOR NEW DESIGN AFTER 18 SEPTEMBER 1998 Provided by IHSNot for ResaleNo reproduction or networking permitted wi

5、thout license from IHS-,-,-MIL-DTL-3922/54E 2 TABLE I. Dash numbers 001, 003 and dimensions. PIN M3922/54- Dimensions 1/ 2/ 3/ Used with Used with A B Dash no. 4/ Waveguide M85/ Mating flange M3922/ Dash no. 5/ Waveguide M85/ Mating flange M3922/ _ .504 .001 (12.80) (0.03) _ .254 .001 (6.45) (0.03)

6、001 1-102 and 1-106 59-003 002 1-103 59-004 003 3-006 59-005 .362 +.002 (9.19) (0.05) -.000 .222 +.002 (5.64) (0.05) -.000 Dimensions 1/ 2/ 3/ - Continued Dash no. 4/ Dash no. 5/ C D BSC E BSC G H J K 001 002 .875 .015 (22.22) (0.38) .335 (8.51) .320 (8.13) .002 (0.05) .015 (0.38) .188 .015 (4.78) (

7、0.38) .156 (3.96) 003 .750 .005 (19.05) (0.13) .265 (6.73) .250 (6.35) .002 (0.05) .005 (0.13) .187 .005 (4.75) (0.13) .109 (2.77) 1/ Dimensions are in inches. Dimensions are in accordance with ASME-Y14.5M. 2/ Millimeter equivalents (to the nearest 0.01 mm) are given for general information only and

8、 are based upon 1.00 inch = 25.4 mm. 3/ Millimeters are in parentheses. 4/ Material shall be copper alloy. 5/ Material shall be aluminum alloy. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-3922/54E 3 FIGURE 2. Flange configuration (-005 th

9、rough -016). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-3922/54E 4 NOTES: 1. Dimensions are in inches. Dimensions are in accordance with ASME-Y14.5M. 2. Millimeter equivalents (to the nearest 0.01 mm) are given for general information on

10、ly and are based upon 1 inch = 25.4 mm. 3. Millimeters are in table. 4. Roughness of mating surfaces shall not exceed 63 micro-inches in accordance with ASME-B46.1, except that flaws shall be included in the roughness height measurement. FIGURE 2. Flange configuration (-005 through -016) - Continued

11、. Inches mm .001 .003 .015 .016 .044 .077 .094 .125 0.02 0.08 0.38 0.41 1.12 1.96 2.39 3.18 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-3922/54E 5 TABLE II. Dash numbers 005 thru 016 and dimensions. PIN M3922/54- Dimensions 1/ 2/ 3/ Used

12、with Used with Dash no. 4/ Waveguide M85/1- Mating flange M3922/59- Dash no. 5/ Waveguide M85/1- Mating flange M3922/59- A _ 1.122 .004 (28.50) (0.10) B _ .497 .004 (12.62) (0.10) 005 073 069 015 006 071 072 177 016 007 075 079 013 008 077 078 178 014 .900 .004 (22.86) (0.10) .400 .004 (10.16) (0.10

13、) 009 089 093 - 010 090 091 180 - .622 .002 (15.80) (0.05) .311 .002 (7.90) (0.05) 011 069 073 007 012 071 072 177 009 1.122 .004 (28.50) (0.10) .497 .004 (12.62) (0.10) 013 075 079 006 014 077 078 178 008 .900 .004 (22.86) (0.10) .400 .004 (10.16) (0.10) 015 089 093 001 016 090 091 180 002 .622 .00

14、2 (15.80) (0.05) .311 .002 (7.90) (0.05) Dimensions 1/ 2/ 3/ - Continued. Dash no. 4/ Dash no. 5/ C .015 (0.38) D BSC E BSC F G .015 (0.38) H J .015 (0.38) 005 006 1.875 (47.62) .737 (18.72) .676 (17.17) .164-32 UNC-2B 1.625 (41.27) .250 .015 (6.35) (0.38) .625 (15.88) 007 008 1.625 (41.27) .640 (16

15、.26) .610 (15.49) .164-32 UNC-2B 1.422 (36.12) .160 .010 (4.06) (0.25) .438 (11.12) 009 010 1.312 (33.32) .478 (12.14) .497 (12.62) .138-32 UNC-2B 1.000 (25.40) .250 .015 (6.35) (0.38) .438 (11.12) 011 012 1.875 (47.62) .737 (18.72) .676 (17.17) .169 + .003 (4.29) (0.08) -.000 1.625 (41.27) .250 .01

16、5 (6.35) (0.38) .625 (15.88) 013 014 1.625 (41.27) .640 (16.26) .610 (15.49) .169 + .003 (4.29) (0.08) -.000 1.422 (36.12) .160 .010 (4.06) (0.25) .438 (11.12) 015 016 1.312 (33.32) .478 (12.14) .497 (12.62) .144 + .003 (3.66 (0.08) -.000 1.000 (25.40) .250 .015 (6.35) (0.38) .438 (11.12) See footno

17、tes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-3922/54E 6 TABLE II. Dash numbers 005 thru 016 and dimensions. - Continued. Dimensions 1/ 2/ 3/ - Continued. Dash no. 4/ Dash no. 5/ K L M Min P .005 (0.13) Q R T V 005 006

18、1.253 .003 (31.83) (0.08) .628 .003 (15.95) (0.08) .875 (22.23) .437 (11.10) .004 (0.10) .203 (5.16) .003 (0.08) .004 (0.10) 007 008 1.003 .003 (25.48) (0.08) .503 .003 (12.78) (0.08) .750 (19.05) .312 (7.92) .003 (0.08) .250 (6.35) .003 (0.08) .004 (0.10) 009 010 .705 .002 (17.91) (0.05) .394 .002

19、(10.01) (0.05) 1.000 (25.40) .312 (7.92) .002 (0.05) - .002 (0.05) .004 (0.10) 011 012 1.253 .003 (31.83) (0.08) .628 .003 (15.95) (0.08) .875 (22.23) .437 (11.10) .004 (0.10) - .003 (0.08) .002 (0.05) 013 014 1.003 .003 (25.48) (0.08) .503 .003 (12.78) (0.08) .750 (19.05) .312 (7.92) .003 (0.08) -

20、.003 (0.08) .002 (0.05) 015 016 .705 .002 (17.91) (0.05) .394 .002 (10.01) (0.05) 1.000 (25.40) .312 (7.92) .002 (0.05) - .002 (0.05) .002 (0.05) 1/ Dimensions are in inches. Dimensions are in accordance with ASME-Y14.5M. 2/ Millimeter equivalents (to the nearest 0.01 mm) are given for general infor

21、mation only and are based upon 1 inch = 25.4 mm. 3/ Millimeters are in parentheses. 4/ Materials shall be copper alloy. 5/ Materials shall be aluminum alloy. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-3922/54E 7 REQUIREMENTS: Dimensions

22、and configuration: See figures 1 and 2 and tables I and II. Material: Metallic alloy as specified in tables I and II. Marking: See figures 1 and 2. PIN: M3922/54- (and dash number from tables I and II). TABLE III. Cross-reference and engineering information. PIN M3922/54- AN nomenclature Frequency r

23、ange (GHz) 001 002 003 005 006 007 008 009 010 011 012 013 014 015 016 UG-595/U UG-597/U UG-599/U - - - - - - - - - - - - 18.0 - 26.5 18.0 - 26.5 26.5 - 40.0 7.05 - 10.00 7.05 - 10.00 8.20 - 12.40 8.20 - 12.40 12.40 - 18.00 12.40 - 18.00 7.05 - 10.00 7.05 - 10.00 8.20 - 12.40 8.20 - 12.40 12.40 - 18

24、.00 12.40 - 18.00 Part M3922/54-004 has been canceled. Referenced documents. In addition to MIL-DTL-3922, this specification sheet references the following documents: ASME-B46.1 ASME-Y14.5M Marginal notations are not used in this revision to identify changes with respect to the previous issue due to

25、 the extent of the changes. Custodians: Preparing activity: Army - CR DLA - CC Navy - EC Air Force 85 (Project 5985-2013-031) DLA - CC Review activities: Army - AV, MI Navy - AS, MC, OS, SH Air Force - 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil/. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-