DLA MIL-DTL-31009-1995 HOOD COLD WEATHER SECURITY POLICE《安全部队冬天用防护帽》.pdf

《DLA MIL-DTL-31009-1995 HOOD COLD WEATHER SECURITY POLICE《安全部队冬天用防护帽》.pdf》由会员分享，可在线阅读，更多相关《DLA MIL-DTL-31009-1995 HOOD COLD WEATHER SECURITY POLICE《安全部队冬天用防护帽》.pdf（29页珍藏版）》请在麦多课文档分享上搜索。

1、W 9999906 1981905 460 W 1 INCH POUND/ O1 June 1995 MIL-DTL-31009 DETAIL SPECIFICATION HOOD, COLD WEATHER, SECURITY POLICE This specification is approved for use by the Defense Logistics Agency and is available for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope.

2、This specification establishes requirements of a cold weather hood for the Security Police that coordinates with the Jacket, Cold Weather, Security Police MIL-DTL-31008. 1.2 Classification. The hood shall be furnished in one of the following sizes as specified (see 6.4). Small Large . Extra extra la

3、rge Medium Extra large Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: Defense Personnel Support Center, Clothing and Textiles Directorate, Attn: DPSC-FQSC, 2800 South 20th Street, Philadelphia,

4、 PA 19145-5099, by using the Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. msc N/A FSC 8415 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking

5、permitted without license from IHS-,-,-9999906 L98L9Ob 3T7 MIL-DTL-31009 2. APPLICABLE DOCUMENTS 2.1 Government documents 2.1.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwi

6、se specified, the issues of these documents shall be those listed in the issue of the Deprtment of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the solicitation (see 6.4). SPECIFICATIONS FEDERAL A-A-5 O 19 9 DDD-L- 2 O V-F-106 KK-L-2004 UU-P-2 6 8 V-B-871 T

7、-T-881 M:i L I TARY MIL-P-116 MIL-B-371 MIL-C-6590 MIL-F-21840 MIL-C-44187 MIL-C-44296 STANDARDS FEDEW FED-STD-191 FED-STD-751 MIL I TARY MIL-STD-129 MIL-STD-147 Thread, Polyester Core, Cotton- or Polyester-Covered Label, For Clothing, Equipment, and Tentage (General Use) Fasteners, Slide, Interlock

8、ing Leather, Horsehide, Chrome Tanned, for Gloves, Garment, and Equipage. Paper, Kraft, Untreated, Wrapping Button, Sewing Hole, and Button, Staple, (Plastic) Twine, Cotton, Seine PrEservation, Methods of Braid, Textile, Tubular Cloth, Pile (Synthetic Mouton, Knitted) Fastener Tapes, Hook and Loop,

9、Synthetic Cloth, Laminated, Waterproof and Moisture Vapor Permeable Cloth, Fusibles Textile Test Methods Stitches, Seams, and Stitching Marking for Shipment and Storage Palletized Unit Loads 6 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL

10、-31009 MIL-STD-1667 Provisions for Evaluating Quality of Hoods, Cold Weather, Extreme Cold Weather and Flyers (Unless otherwise indicated, copies of Federal and military specifications, standards and handbooks are available from the Standardization Documents Order Desk, Bldg. 4D, 700 Robbins Avenue,

11、 Philadelphia, PA 19111-5094.) 2. APPLICABLE DOCUMENTS 2.1 Government Documents 2.1.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these document

12、s shall be those listed in the issue of the Department of Defense index of Specifications and Standards (DODISS) and supplement thereto, cited in the solicitation (see 6.4). 2.1.2 Other Government documents, drawincrs, and publications. The following other Government documents, drawings, and publica

13、tions form a part of this document to the extent specified herein. Unless otherwise spetified, the issues are those cited in solicitation. U.S. Postal Manual (Copies of the manual may be obtained from the Superintendent of Documents, U.S. Government Printing Office, Washington, DC 20402-0001.) 2.2 N

14、on-Government publications. The following document(s) form a part of this document to the extent specified herein. Unless otherwise specified, the issues of the documents which are DoD adopted shall be those listed in the issue of the DODISS cited in the solicitation. Unless otherwise specified, the

15、 issues of documents not listed in the DODISS are the issues of the documents cited in the solicitation (see 6.4). AMERICAN SOCIETY FOR TESTING AND MATERIALS ASTM-D 19;4 Standard Practice for Methods for Closing, Sealing and reinforcing Fiberboard Boxes ASTM-D 3951 Standard Pzactice for Commercial P

16、ackaging (Applications for copies should be addressed to the American Society for Testing and Materials, 1916 Race Street, Philadelphia, PA 19103-1187.) 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-1. MIL-DTL-31009 + AMERICAN NATIONAL STANDARD I

17、NSTITUTE (ANSI) ANSI/ASQC 21.4 - Sampling Procedures and Tables for Inspection by Attributes (Copies should be obtained from the American National Standards Institute, 1430 Broadway, New York, NY 10018-3308.) (Non-Government standards and other publications are normally available from the organizati

18、ons that prepare or distribute the documents. These documents also may be available in or through libraries or other informational services.) 2.3 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precede

19、nce. Nothing in this document however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 First article. shall be subjected to first article inspection in accordance with 4.3. When specified (see 6.4 and 6.5), a sample 3.2 Materials. when pr

20、actical as long as they meet the requirements of this document. It is encouraged that recycled materials be used 3.2.1 Basic macerial. the hood bottom edge, and the cowl flaps shall conform to MIL-C-44187 and shall be USAF Blue, Shade No. 1613. The basic material for the outer shell, 3.2.2 Mouton li

21、ninq. match the color of the basic fabric, and shall conform to type II The liiling for the hood shall be dyed to of MIL-C-6590. 3.2.3 Drawstrinqs. type III of MIL-B-371, and shall be dyed to match the color of the basic fabric. Each drawstring shall be 23 inches (plus or minus 1 inch) long. or impr

22、egnated with cellulose acetate or cellulose acetate butyrate. inches (plus or minus 1/8 inch). 3.2.4 Drawstrinq reinforcements. reinforcements shall conform to type I; class 2; 1-1/2 to 3-1/4 ounces of KK-L-2004, color b!.ack. The cord or the drawstrings shall conform to The ends of the drawstrings

23、shall be tipped The length of the tipping or impregnation shall be 5/8 The leather for the drawstring 3.2.5 Buttons. shall conform to type II, class D, styles 20 and 21, size 30 line of V-B-871 and sha1.1 be DOD Button Shade Blue, CA 62002. The buttons for attaching the hood to the jacket 4 Provided

24、 by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-. 99994Ob 1981909 OOb W MIL-DTL-31009 3.2.6 Thread. The polyester core thread used for seaming and stitching the hoods shall conform to type I of A-A-50199 in the following sizes: - Use Ticket No. ply Seaming a

25、nd stitching 50, 70 Bartacks 50 Overedging 70 2 2 2 The color of the thread shall be Blue AT, CA 66060. 3.2.7 Fastener tapes. The hook and loop fastener tape shall be Black 3230 conforming to type I or type IA, class I of MIL-F-21840. 3.2.8 Fusible interlininq. The fusible interlining used on the co

26、wl flaps shall be type V, style B, class 1 of MIL-C-44296 and the color shall be black, 3.2.9 Slide fasteners. The slide fastener for the hood separation shall conform to type I, style 3, size M of V-F-106 and of Table I of this document. The chain and any other metal components, except the latch an

27、d spring of the automatic slider of the slide fastener shall be brass with a black chemical finish. The slide fastener tapes shall be cotton/warp and nylon filling, cotton, or polyester and shall be dyed to approximate the shade of the basic fabric. The tape shall not shrink more than 2 percent in t

28、he direction of the warp when tested as specified in 4.4.1.1. TABLE I. Slide fastener Hood separation size Type Style Size Length Small I 3 M 16-1/2 inches Medium I 3 M 17 inches Large I 3 M 17-1/2 inches Extra large I 3 M 18 inches Extra extra large I 3 M 18-1/2 inches 3.2.10 Cord. The cord beading

29、 used in the edges of the hood separation slide fastener cover shall conform to type I, No. 18 of T-T-881. 3.2.11 Seam seulinq tape. The tape for covering and sealing all designated seams and stitching shall be cut in 12 1/16 inch wide strips from USAF Blue, Shada No. 1613 iaminated cloth fabricated

30、 in layers as follows: Layer 1 Nylon tricot weighing 1.5 i 0.3 ounces per square yard 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-= 9999906 1981910 828 MIL-DTL-31009 Layer 2 Microporous expanded polytetrafluoroethylene film weighing 0.6 +0.2 or

31、 -0.1 ounces per square yard Layer 3 Adhesive, thermoplastic not less than 5.4 mils thick 3.2.11,l Alternative urethane acrvlic seam sealinq tape. The alternative seam sealing tape for the optional polyolefin microporous laminated basic material of MIL-C-44187 shall meet the following characteristic

32、s: A. Width, inches 1 (+ 1/16) B. Nylon knit backing: nylon tricot fabric weighing 1.2 ounces per sq. yd. minimum C. The middle layer shall be thermoset crosslinked urethane acrylic barrier weighing 1.0 oz./sq. yd. minimum. The outer layer shall consist of a low temperature polyurethane adhesive wit

33、h 240 degrees F (nominal) melt point not less than 7.5 mils thick. (See 6.8 for recommended settings. Under no circumstances shall the tape/alternate polyolefin material combination be taped on a tape machine incorporating a nozzle heat output in excess of 600 degrees centigrade and without an indep

34、endent nozzle air pressure control. ) 3.2.12 Heat sealinq. Seams and stitching, as indicated in Table III, shall be sealed with seam-sealing tape on the innerside of the hood. The entire width of the seam tape shall be hot-air sealed over the seam or stitching. shall be appliGd without tension and s

35、hall be applied so that a minimum of 3/16 inch xerlap is on both sides of the sewn seam. Every effort shall be made to avoid tape end joints where the tape passes over taped seams on the jacket. All seam tapes shall overlap a minimum of 1/4 inTk at joifiing points. Sealed seams and stitchings shall

36、show no leakage when tested as specified in 4.4.1.1 and 4.5.2. All seam tapes 3.2.13 Labels. Each hood shall have a combination size, identification, and an instruction label. The label shall show colorfastness to dry cleaning in accordance with DDD-L-20. The label shall be centered on the hood bott

37、om edge within 1/2 inch, and sewn on all four sides 1/16 inch from edge, in such a manner that the stitches do not show on the back exterior of the outershell. 3.2.13.1 Combination. size, identification, and instruction label. The label shall conform to type VI, class 14 of DDD-L-20, and shall be 1-

38、1/4 inch by 3 inches. The label shall contain the following information: 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-9999906 l198L9LL 764 MIL-DTL-31009 Size: Hood, Cold Weather, Security Police Contract No. DLA-100-00-0-0000 (example) Stock No.

39、 8415-00-000-0000 (example) Contractors Name: PROFESSIONALLY DRY CLEAN ONLY USI11G A CLEAR DISTILLED SOLVENT RINSE MIL-DTL-31009 NOTE: The contractor shall insert the applicable information. 3.2.13.2 Label/taq. Each item shall be individually bar-coded with the type VIII, class 17 label/tag of DDD-L

40、-20. This label/tag shall be located so that it is completely visible on the item when it is iolded and/or packaged as specified and so that it causes no damage to the item. 3.3 Desian. The hood shall be detachable (button), mouton lined, with a drawstring adjustment, a slide fastener separation, an

41、d a cowl flap. This hood is intended to be worn with the security police winter jacket. 3.4 Patterns. Standard patterns to be used to cut working patterns will be furnished by the Government. The manufacturers working patterns shall be identical in size and shape to the applicable Government pattern

42、s except that additional notches for use during construction are allowed on the working patterns. Also, minor modifications are permitted where necessary when using automatic equipment. These modifications shall not alter the dimensional, serbiceability or appearance requirements cited in the specif

43、ication. 3.4.1 Pattern parts. The hood shall be cut from the materials specified herein in accordance with the pattern parts listed in Table II. TABLE II. List of pattern parts Material Pattern Part Parts Cut Basic fabric (see 3.2.1) Hood front panel Hood side panel Hood center panel Cowl flap Hood

44、bottom edge Throat tab Slide fastener cover Fusible interlining Cowl flap (see 3.2.8) Mouton (lining) Hood front pafie1 (see 3.2.2) Hood side panel Hood center panel 4 2 2 1 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-31009 3.5 Stitches

45、, seams, and stitchinqs. Stitches, seams, and stitchings used in the construction of the hood shall conform to FED-STD-751. Whenever two or more methods, seams, or stitches are specified for the same operation, any one of them may be used. All seams shall start and finish evenly. Seam allowances sha

46、ll be maintained so that raw edges, run-Offs, twists, pleats, puckers, or open seams will not result. Thread tension shall be maintained so that there will be no tight or loose tension. The looper thread (underthread) of stitch type 401 shall be on the inside of the hood. 3.5.1. Thread breaks and en

47、ds of seams. Thread breaks (all stitch types) shall be secured by stitching back of each end not less than 1/2 inch. Skipped stitches or thread breaks of stitch type 401 may be repalred using stitch type 301. Ends of all seams and stitches produced with stitch type 301, if not caught in other seams

48、or stitchings, shall be backtacked not less than 1/4 inch. not less than three stitches. The ends of stitching on labels shall be overlapped 3.5.1.1 Type 301 stitchinq. backstitched or overstitched not less than 1/2 inch except where ends are turned under or caught in other seams or stitching. Ends

49、of a continuous line of stitching shall overlap not less than 1/2 inch. Thread tensions shall be maintained so that there will be no loose stitching resulting in loose bobbin or top thread or excessively tight stitching resulting in puckering of the material sewn. The lock shall be embedded in the material sewn. Ends of all stitching shall be 3.5.1.2 Repairs of type 301 stitchinq. Repairs of type 301 stitching shall be as follows: a. When threa