DLA MIL-DTL-13625 1 B-2009 SWITCHES PULL SWITCHES PUSH SWITCHES BEAM SELECTING HEADLIGHT ELECTRICAL (28 VOLTS DC MAXIMUM FOR MILITARY VEHICLES).pdf

《DLA MIL-DTL-13625 1 B-2009 SWITCHES PULL SWITCHES PUSH SWITCHES BEAM SELECTING HEADLIGHT ELECTRICAL (28 VOLTS DC MAXIMUM FOR MILITARY VEHICLES).pdf》由会员分享，可在线阅读，更多相关《DLA MIL-DTL-13625 1 B-2009 SWITCHES PULL SWITCHES PUSH SWITCHES BEAM SELECTING HEADLIGHT ELECTRICAL (28 VOLTS DC MAXIMUM FOR MILITARY VEHICLES).pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、AMSC N/A FSC 5930 MIL-DTL-13625/1B 21 January 2009 SUPERSEDING MIL-DTL-13625/1A 27 March 2003 DETAIL SPECIFICATION SHEET SWITCHES, PULL; SWITCHES, PUSH; SWITCHES, BEAM SELECTING, HEADLIGHT: ELECTRICAL (28 VOLTS DC MAXIMUM, FOR MILITARY VEHICLES) This specification is approved for use by all Depart-

2、ments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification and MIL-DTL-13625. FIGURE 1. INCH-POUND NASM35338-46 MS35691-20 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from I

3、HS-,-,-MIL-DTL-13625/1B 2 Notes: 1. Type IV (Single Pole, Single Throw, heavy duty, normally open), Class A (slow make and break), Grade 2 (open) of procurement specification. 2. 300 Amp resistive load, 150 Amp inductive load. 3. Force required to operate the switch shall be 12 2 pounds. 4. Shall wi

4、thstand a minimum overload force of 300 pounds without damage. 5. Shall not exceed a maximum weight of 11 ounces. 6. Nut shall not be coated with Black Oxide. 7. Threads shall be in accordance with screw thread standard for FED-STD-H28. 8. Dimensions are in inches. Unless otherwise specified, tolera

5、nces are .01 on decimals, 0 30 on angles. 9. For design feature purposes, this specification sheet takes precedence over procurement documents referenced herein. 10. This specification sheet is not intended to limit construction to features other than as shown heron by dimensions, notations or refer

6、enced documents. 11. Referenced documents shall be of the issue in effect on the date on invitations for bid. 12. Marking shall consist of the part or identifying number (PIN) and Manufacturers identification in accordance with MIL-STD-130. FIGURE 1 continued. Supersedes Part or Identifying Number (

7、PIN) MS Part No. Former Part No. MIL-DTL-13625/1-1 MS27199-1 6200102 The margins of this specification are marked with vertical lines to indicate where modifications from this amendment were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccura

8、cies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations. Referenced documents: MIL-DTL-13625 MIL-STD-130 FED-STD-H28 Custodian: Preparing activity: Army - AT DLA - CC DLA CC (Proje

9、ct 5930-2008-082) NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil/ . Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-