DLA MIL-DTL-13623 1 B-2010 SWITCHES ROTARY 28 VOLT DC.pdf

《DLA MIL-DTL-13623 1 B-2010 SWITCHES ROTARY 28 VOLT DC.pdf》由会员分享，可在线阅读，更多相关《DLA MIL-DTL-13623 1 B-2010 SWITCHES ROTARY 28 VOLT DC.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、AMSC N/A FSC 5930 INCH-POUND MIL-DTL-13623/1B 22 February 2010 SUPERSEDING MIL-DTL-13623/1A 7 June 2004 DETAIL SPECIFICATION SHEET SWITCHES, ROTARY, 28 VOLT DC Inactive for new design after 8 March 1999. This specification is approved for use by all Departments and Agencies of the Department of Defe

2、nse. The requirements for acquiring the switches described herein shall consist of this specification sheet and MIL-DTL-13623. FIGURE 1. Lever Stem Detail Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-13623/1B 2 FIGURE 1. Lever Stem Detail

3、Continued. SCREW MS 35265-43 WASHER NASM 35338-42 NUT PT NO 5381233 WASHER NASM 35333-44 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-13623/1B 3 With lever in position “1” switch is off, with lever in position “2” contacts “A” 10 Amp Induc

4、tive Load; 5 Amp Lamp Load. 3. Flats shall be as shown when the switch lever is in position 1. 4. Plain connectors mate with MS27144-1 and MS27144-2. Ribbed connectors mate with MS27144-3. Dummy connectors (8338561 with 7982907) not supplied as part of switch. 5. Lever shall not be supplied as part

5、of switch. Lever used will be determined by vehicle application. For information and reference only see drawing 5381088, 10896915 and 10938483. 6. Dimensions are in inches. Unless otherwise specified, tolerances are .02 on decimals and + 2 on angles. 7. For design feature purposes, this specificatio

6、n sheet takes precedence over procurement documents referenced herein. 8. Referenced documents shall be of the issue cited in the solicitation or contract. 9. This standard is not intended to limit construction to features other than as shown hereon by dimensions, notations and referenced documents.

7、 10. The part or identifying number consists of the specification sheet number plus a dash number. Example: MIL-DTL-13623/1-2. 11. Marking shall consist of the part of identifying number and the manufacturers identification in accordance with MIL-STD-130. Identification marking of terminals A, B, C

8、and D shall be adjacent to the terminals. Reference Documents: MIL-DTL-13623 MIL-STD-130 Changes from previous issue. The margins of this specification are marked with vertical lines to indicate where modifications from this amendment were made. This was done as a convenience only and the Government

9、 assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations. Custodians: Preparing activity: Army AT DLA CC DLA CC (Project 5930-2009-0

10、30) NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil/ . Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-