DLA DSCC-VID-V62 11620-2011 MICROCIRCUIT DIGITAL CURRENT LIMITED POWER DISTRIBUTION SWITCH MONOLITHIC SILICON.pdf

《DLA DSCC-VID-V62 11620-2011 MICROCIRCUIT DIGITAL CURRENT LIMITED POWER DISTRIBUTION SWITCH MONOLITHIC SILICON.pdf》由会员分享，可在线阅读，更多相关《DLA DSCC-VID-V62 11620-2011 MICROCIRCUIT DIGITAL CURRENT LIMITED POWER DISTRIBUTION SWITCH MONOLITHIC SILICON.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、 REVISIONS LTR DESCRIPTION DATE APPROVED Prepared in accordance with ASME Y14.24 Vendor item drawing REV PAGE REV PAGE REV STATUS OF PAGES REV PAGE 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY Phu H. Nguyen DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil Original date

2、 of drawing YY MM DD CHECKED BY Phu H. Nguyen TITLE MICROCIRCUIT, DIGITAL, CURRENT LIMITED POWER DISTRIBUTION SWITCH, MONOLITHIC SILICON 11-10-27 APPROVED BY Thomas M. Hess SIZE A CODE IDENT. NO. 16236 DWG NO. V62/11620 REV PAGE 1 OF 14 AMSC N/A 5962-V001-12 Provided by IHSNot for ResaleNo reproduct

3、ion or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/11620 REV PAGE 2 1. SCOPE 1.1 Scope. This drawing documents the general requirements of a high performance current limited power distribution switch microcircuit, wit

4、h an operating temperature range of -55C to +125C. 1.2 Vendor Item Drawing Administrative Control Number. The manufacturers PIN is the item of identification. The vendor item drawing establishes an administrative control number for identifying the item on the engineering documentation: V62/11620 - 0

5、1 X E Drawing Device type Case outline Lead finish number (See 1.2.1) (See 1.2.2) (See 1.2.3) 1.2.1 Device type(s). Device type Generic Circuit function 01 TPS2041B-EP Current limited power distribution switch 1.2.2 Case outline(s). The case outlines are as specified herein. Outline letter Number of

6、 pins JEDEC PUB 95 Package style X 15 JEDEC MO-178 Plastic small outline package 1.2.3 Lead finishes. The lead finishes are as specified below or other lead finishes as provided by the device manufacturer: Finish designator Material A Hot solder dip B Tin-lead plate C Gold plate D Palladium E Gold f

7、lash palladium Z Other Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/11620 REV PAGE 3 1.3 Absolute maximum ratings. 1/ Input voltage range (IN) (VI(IN) -0.3 V to +6 V 2/ O

8、utput voltage range (OUT) (VO(OUT) -0.3 V to +6 V 2/ Input voltage range (EN) (VI(EN) -0.3 V to +6 V Voltage range (OC) (VI(OC) -0.3 V to +6 V Continuous output current (IO(OUT) . Internally limited Continuous total power dissipation See dissipation ratings table. Operating virtual junction temperat

9、ure range (TJ) . -55C to 125C Storage temperature range (Tstg) . -65C to 150C Lead temperature, soldering (1.6 mm (1/16 in) from case for 10 s) 260C Electrostatic discharge (ESD) protection: Human Body Model (HBM) (H2) 2500 V Machine Model (MM) (M0) . 50 V Charged Device Model (CDM) (C5) . 1500 V Di

10、ssipating ratings table: 1.4 Recommended operating conditions. Input voltage (IN) (VI(IN). 2.7 V to 5.5 V Input voltage (EN) (VI(EN) . 0 V to 5.5 V Continuous output current (OUT) (IO(OUT) 0 mA to 500 mA Operating virtual junction temperature (TJ) . -55C to 125C 2. APPLICABLE DOCUMENTS JEDEC SOLID S

11、TATE TECHNOLOGY ASSOCIATION (JEDEC) JEDEC PUB 95 Registered and Standard Outlines for Semiconductor Devices JEDEC STD 51-7 High Effective Thermal Conductivity Test Board for Leaded Surface Mount Packages (Copies of these documents are available online at http:/www.jedec.org or from JEDEC Solid State

12、 Technology Association, 3103 North 10th Street, Suite 240S, Arlington, VA 22201.) 1/ Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond

13、those indicated under “recommended operating conditions” is not implied. Exposure to absolute maximum rated conditions for extended periods may affect device reliability. 2/ All voltage are with respect to GND Package TA 25C Power ratings Derating factor Above TA= 25C TA= 25C Power rating TA= 85C Po

14、wer rating Case X 285 mW 2.85 mW/C 155 mW 114 mW Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/11620 REV PAGE 4 3. REQUIREMENTS 3.1 Marking. Parts shall be permanently and

15、 legibly marked with the manufacturers part number as shown in 6.3 herein and as follows: A. Manufacturers name, CAGE code, or logo B. Pin 1 identifier C. ESDS identification (optional) 3.2 Unit container. The unit container shall be marked with the manufacturers part number and with items A and C (

16、if applicable) above. 3.3 Electrical characteristics. The maximum and recommended operating conditions and electrical performance characteristics are as specified in 1.3, 1.4, and table I herein. 3.4 Design, construction, and physical dimension. The design, construction, and physical dimensions are

17、as specified herein. 3.5 Diagrams. 3.5.1 Case outline. The case outline shall be as shown in 1.2.2 and figure 1. 3.5.2 Terminal connections and terminal functions. The terminal connections and terminal functions shall be as shown in figure 2. 3.5.3 Functional block diagram. The functional block diag

18、ram shall be as shown in figure 3. 3.5.4 Test circuit and voltage waveforms. The test circuit and voltage waveforms shall be as shown in figure 4. 3.5.5 Turn on delay and rise time with 1 F load. The turn on delay and rise time with 1 F load shall be as shown in figure 5. 3.5.6 Turn off delay and fa

19、ll time with 1 F load. The turn off delay and fall time with 1 F load shall be as shown in figure 6. 3.5.7 Turn on delay and rise time with 100 F load. The turn on delay and rise time with 100 F load shall be as shown in figure 7. 3.5.8 Turn off delay and fall time with 100 F load. The turn off dela

20、y and fall time with 100 F load shall be as shown in figure 8. 3.5.9 Short circuit current, device enables into short. The short circuit current, device enabled into short shall be as shown in figure 9. 3.5.10 Inrush current with different load capacitance. The inrush current with different load cap

21、acitance shall be as shown in figure 10. 3.5.11 3 load connected to enabled device. The 3 load connected to enabled device shall be as shown in figure 11. 3.5.12 2 load connected to enabled device. The 2 load connected to enabled device shall be as shown in figure 12. Provided by IHSNot for ResaleNo

22、 reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/11620 REV PAGE 5 TABLE I. Electrical performance characteristics. 1/ Test Symbol Conditions 2/ 3/ TJLimits Unit Min Max Power Switch Static drain source on

23、state resistance, 5 V or 3.3 V operation rDS(on)VI(IN)= 5 V or 3.3 V, IO= 0.5 A -55C TJ 125C 135 m Static drain source on state resistance, 2.7 V operation 4/ VI(IN)= 2.7 V, IO= 0.5 A -55C TJ 125C 150 Rise time, output 4/ trVI(IN)= 5.5 V CL= 1 F RL= 10 TJ= 25C 1.5 ms VI(IN)= 2.7 V 1 Fall time, outpu

24、t 4/ tfVI(IN)= 5.5 V 0.05 0.5 VI(IN)= 2.7 V 0.05 0.5 Enable Input () High level input voltage VIH2.7 V VI(IN) 5.5 V 2 V Low level input voltage VIL2.7 V VI(IN) 5.5 V 0.8 V Input current IIVI(EN)= 0 V or 5.5 V -0.5 0.5 A Turn on time 4/ tonCL= 100 F, RL= 10 3 ms Turn off time 4/ toffCL= 100 F, RL= 10

25、 10 ms Current limit Short circuit output current VI(IN) = 5 V, OUT connected to GND, device enable into short circuit TJ= 25C 0.65 1.25 A -55C TJ 125C 0.6 1.3 Supply current Supply current, low level output No load on OUT, VI(EN)= 5.5 V or VI(EN)= 0 V TJ= 25C 1 A -55C TJ 125C 5 Supply current, high

26、 level output No load on OUT, VI(EN)= 0 V or VI(EN)= 5.5 V TJ= 25C 60 A -55C TJ 125C 70 Leakage current OUT connected to ground, VI(EN)= 5.5 V or VI(EN)= 0 V -55C TJ 125C 1 TYP A Reverse leakage current VI(OUT)= 5.5 V, IN = ground TJ= 25C 0 TYP A Under voltage lockout Low level input voltage, IN 2 2

27、.5 V Hysteresis, IN TJ= 25C 75 TYP mV Overcurrent () Output low voltage, VOL(/OC)IO(OC)= 5 mA 0.4 V Off state current 4/ VO(OC)= 5 V or 3.3 V 1 A OCdeglitch 4/ OCassertion or deassertion 4 15 ms See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted witho

28、ut license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/11620 REV PAGE 6 TABLE I. Electrical performance characteristics - Continuous. 1/ Test Symbol Conditions 2/ 3/ TJLimits Unit Min Max Thermal shutdown 5/ Thermal shutdown threshold 4/ 135 C Recovery f

29、rom thermal shutdown 4/ 125 C Hysteresis 4/ 10 TYP C 1/ Testing and other quality control techniques are used to the extent deemed necessary to assure product performance over the specified temperature range. Product may not necessarily be tested across the full temperature range and all parameters

30、may not necessarily be tested. In the absence of specific parametric testing, product performance is assured by characterization and/or design. 2/ Over recommended operating junction temperature range, VI(IN)= 5.5 V, IO = 0.5 A, VI(EN) = 0 V (unless otherwise noted). 3/ Pulse testing techniques main

31、tain junction temperature close to ambient temperature; thermal effects must be accounted for separately. 4/ Specified by design. 5/ The thermal shutdown only reacts under overcurrent conditions. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LA

32、ND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/11620 REV PAGE 7 Case X 1 35 4Db5 PLS0.20 ME E1AA1SEATINGPLANE0.10SEEDETAIL ADETAIL A0-8GAGEPLANEL1cLePIN 1INDEX AREADimensions Symbol Millimeters Symbol Millimeters Min Max Min Max A 1.45 E 1.45 1.75 A1 0.00 0.15 E1 2.60 3.00 b

33、0.30 0.50 e 0.95 BSC c 0.08 0.22 L 0.30 0.50 D 2.75 3.05 L1 0.25 TYP NOTES: 1. All linear dimensions are in millimeters. 2. This drawing is subject to change without notice. 3. Body dimensions do not include mold flash or protrusion. Mold flash and protrusion shall not exceed 0.15 per side. 4. Falls

34、 within JEDEC MO-178 Variation AA. FIGURE 1. Case outline. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/11620 REV PAGE 8 Terminal number Terminal symbol I/O Terminal Func

35、tions 1 OUT O Power switch output 2 GND Ground 3 OCO Overcurrent, Open drain output, active low 4 ENI Enable input, logic low turns on power switch 5 IN I Input voltage FIGURE 2. Terminal connections and terminal functions. CHARGEPUMPCURRENTLIMITTHERMALSENSEUVLODRIVERDEGLITCHCSOCOUTSEENOTE AINENGNDN

36、OTICE: A. CS = Current sense. FIGURE 3. Functional block diagram. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/11620 REV PAGE 9 OUTRLCLTEST CIRCUITVO(OUT)90%10%tftr50%90%

37、10%VO(OUT)VI(EN)tontoff50%90%10%VO(OUT)VI(EN)tontoffFIGURE 4. Test circuit and voltage waveforms. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/11620 REV PAGE 10 I(EN)VI(E

38、N)V5 V/divO(OUT)V2 V/divRL= 10CL= 1TA= 25CFt - TIME - 500 s/divFIGURE 5. Turn-On delay and rise time with 1 F load. I(EN)VI(EN)V5 V/divO(OUT)V2 V/divRL= 10CL= 1TA= 25CFt - TIME - 500 s/divFIGURE 6. Turn-Off delay and fall time with 1 F load. Provided by IHSNot for ResaleNo reproduction or networking

39、 permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/11620 REV PAGE 11 I(EN)VI(EN)V5 V/divO(OUT)V2 V/divRL= 10CL= 100TA= 25CFt - TIME - 500 s/divFIGURE 7. Turn-On delay and rise time with 100 F load. I(EN)VI(EN)V5 V/divO(OUT)V2 V/divRL=

40、 10CL= 100TA= 25CFt - TIME - 500 s/divFIGURE 8. Turn-Off delay and fall time with 100 F load. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/11620 REV PAGE 12 I(EN)VI(EN)V5

41、 V/divO(OUT)I500 mA/divt - TIME - 500 s/divFIGURE 9. Short circuit current, device enabled into short. I(EN)VI(EN)V5 V/divO(OUT)I500 mA/divt - TIME - 500 s/divVI= 5 VRL= 10TA= 25C470 F220 F100 FFIGURE 10. Inrush current with different load capacitance. Provided by IHSNot for ResaleNo reproduction or

42、 networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/11620 REV PAGE 13 O(OC)V2 V/divO(OUT)I500 mA/divt - TIME - 2 ms/divFIGURE 11. 3 Load connected to enable device. O(OC)V2 V/divO(OUT)I500 mA/divt - TIME - 2 ms/divFIGURE 12.

43、 2 Load connected to enable device. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/11620 REV PAGE 14 4. VERIFICATION 4.1 Product assurance requirements. The manufacturer is

44、 responsible for performing all inspection and test requirements as indicated in their internal documentation. Such procedures should include proper handling of electrostatic sensitive devices, classification, packaging, and labeling of moisture sensitive devices, as applicable. 5. PREPARATION FOR D

45、ELIVERY 5.1 Packaging. Preservation, packaging, labeling, and marking shall be in accordance with the manufacturers standard commercial practices for electrostatic discharge sensitive devices. 6. NOTES 6.1 ESDS. Devices are electrostatic discharge sensitive and are classified as ESDS class 1 minimum

46、. 6.2 Configuration control. The data contained herein is based on the salient characteristics of the device manufacturers data book. The device manufacturer reserves the right to make changes without notice. This drawing will be modified as changes are provided. 6.3 Suggested source(s) of supply. I

47、dentification of the suggested source(s) of supply herein is not to be construed as a guarantee of present or continued availability as a source of supply for the item. Vendor item drawing administrative control number 1/ Device manufacturer CAGE code Vendor part number Top Side Marking V62/11620-01XE 01295 TPS2041BMDBVTEP PXAM 1/ The vendor item drawing establishes an admini