DLA DSCC-DWG-85018 REV L-2003 ADAPTER ELECTRICAL COAXIAL RADIO FREQUENCY (BETWEEN SERIES SMA TO SERIES TNC)《射频的 同轴电缆的电气适配器(在TNC系列和SMA系列之间)》.pdf

《DLA DSCC-DWG-85018 REV L-2003 ADAPTER ELECTRICAL COAXIAL RADIO FREQUENCY (BETWEEN SERIES SMA TO SERIES TNC)《射频的 同轴电缆的电气适配器(在TNC系列和SMA系列之间)》.pdf》由会员分享，可在线阅读，更多相关《DLA DSCC-DWG-85018 REV L-2003 ADAPTER ELECTRICAL COAXIAL RADIO FREQUENCY (BETWEEN SERIES SMA TO SERIES TNC)《射频的 同轴电缆的电气适配器(在TNC系列和SMA系列之间)》.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、 NOTICE OF REVISION (NOR) This revision described below has been authorized for the document listed. 1. DATE (YYMMDD) 03-01-17 Form Approved OMB No. 0704-0188 Public reporting burden for this collection is estimated to average 2 hours per response, including the time for reviewing instructions, sear

2、ching existing data sources, gathering and maintaining the data needed, and completing and reviewing the collection of information. Send comments regarding this burden estimate or any other aspect of this collection of information, including suggestions for reducing this burden, to Department of Def

3、ense, Washington Headquarters Services, Directorate for Information Operations and Reports, 1215 Jefferson Davis Highway, Suite 1204, Arlington, VA 22202-4302, and to the Office of Management and Budget, Paperwork Reduction Project (0704-0188), Washington, DC 20503. PLEASE DO NOT RETURN YOUR COMPLET

4、ED FORM TO EITHER OF THESE ADDRESSED. RETURN COMPLETED FORM TO THE GOVERNMENT ISSUING CONTRACTING OFFICER FOR THE CONTRACT/ PROCURING ACTIVITY NUMBER LISTED IN ITEM 2 OF THIS FORM.2. PROCURING ACTIVITY NO. 3. DODAAC 4. ORIGINATOR b. ADDRESS (Street, City, State, Zip Code)Defense Supply Center Columb

5、us 3990 East Broad Street Columbus, Ohio 43216-5000 5. CAGE CODE037Z3 6. NOR NO.5935-R002-03 a. TYPED NAME (First, Middle Initial, Last) Ron Gary 7. CAGE CODE037Z3 8. DOCUMENT NO.85018 9. TITLE OF DOCUMENT Adapter, Electrical, Coaxial, Radio Frequency, (Between Series SMA to Series TNC) 10. REVISION

6、 LETTER 11. ECP NO.N/A a. CURRENTK b. NEWL 12. CONFIGURATION ITEM (OR SYSTEM) TO WHICH ECP APPLIESALL 13. DESCRIPTION OF REVISIONSheet 1: Revisions Ltr. Column; add “L” Revisions description column; add “Changes in accordance with NOR 5935-R002-03”. Revisions date column; add “03-01-17” Revisions re

7、v status of pages, blocks 1 and 6, add “L”. Revisions rev status of sheet 1, add “L”. Sheet 6: Revisions rev status of sheet , add “L”. Sheet 6: Add the following new Vendor PIN “ DSCC drawing PIN 1/ Vendor CAGE Vendor reference PIN Number 8501814FP-1 00779 1057848-1 8501814FP-2 00779 1080294-1 8501

8、814FP-3 00779 1057911-1 “ 14. THIS SECTION FOR GOVERNMENT USE ONLY a. (X one) X (1) Existing document supplemented by the NOR may be used in manufacture. (2) Revised document must be received before manufacturer may incorporate this change. (3) Custodian of master document shall make above revision

9、and furnish revised document. b. ACTIVITY AUTHORIZED TO APPROVE CHANGE FOR GOVERNMENTDSCC-VAI c. TYPED NAME (First, Middle Initial, Last)ROBERT HEBER d. TITLECHIEF, INTERCONNECTION DEVICES e. SIGNATURERobert M. Heber f. DATE SIGNED (YYMMDD) 03-01-17 15a. ACTIVITY ACCOMPLISHING REVISIONDSCC-VAI b. RE

10、VISION COMPLETED (Signature)Ron Gary c. DATE SIGNED (YYMMDD)03-01-17 DD Form 1695, APR 92 Previous editions are obsolete Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NOTICE OF REVISION (NOR) This revision described below has been authorized for th

11、e document listed. 1. DATE (YYMMDD) 02-02-01 Form Approved OMB No. 0704-0188 Public reporting burden for this collection is estimated to average 2 hours per response, including the time for reviewing instructions, searching existing data sources, gathering and maintaining the data needed, and comple

12、ting and reviewing the collection of information. Send comments regarding this burden estimate or any other aspect of this collection of information, including suggestions for reducing this burden, to Department of Defense, Washington Headquarters Services, Directorate for Information Operations and

13、 Reports, 1215 Jefferson Davis Highway, Suite 1204, Arlington, VA 22202-4302, and to the Office of Management and Budget, Paperwork Reduction Project (0704-0188), Washington, DC 20503. PLEASE DO NOT RETURN YOUR COMPLETED FORM TO EITHER OF THESE ADDRESSED. RETURN COMPLETED FORM TO THE GOVERNMENT ISSU

14、ING CONTRACTING OFFICER FOR THE CONTRACT/ PROCURING ACTIVITY NUMBER LISTED IN ITEM 2 OF THIS FORM.2. PROCURING ACTIVITY NO. 3. DODAAC 4. ORIGINATOR b. ADDRESS (Street, City, State, Zip Code)Defense Supply Center Columbus 3990 East Broad Street Columbus, Ohio 43216-5000 5. CAGE CODE037Z3 6. NOR NO.59

15、35-R001-02 a. TYPED NAME (First, Middle Initial, Last) Ron Gary 7. CAGE CODE037Z3 8. DOCUMENT NO.85018 9. TITLE OF DOCUMENT Adapter, Electrical, Coaxial, Radio Frequency, (Between Series SMA to Series TNC) 10. REVISION LETTER 11. ECP NO.N/A a. CURRENTJ b. NEWK 12. CONFIGURATION ITEM (OR SYSTEM) TO W

16、HICH ECP APPLIESALL 13. DESCRIPTION OF REVISIONSheet 1: Revisions Ltr. Column; add “K” Revisions description column; add “Changes in accordance with NOR 5935-R001-02”. Revisions date column; add “02-02-01” Revisions rev status of pages, block 1, add “K”. Revisions rev status of sheet 1, add “K”. She

17、et 6: Revisions rev status of sheet , add “K”. Sheet 6: Add the following new Vendor PIN DSCC drawing PIN 1/ Vendor CAGE Vendor reference PIN Number 8501814FP-1 34078 ADT-2699-FF-012-02 8501814FP-2 34078 ADT-2699-FF-013-02 14. THIS SECTION FOR GOVERNMENT USE ONLY a. (X one) X (1) Existing document s

18、upplemented by the NOR may be used in manufacture. (2) Revised document must be received before manufacturer may incorporate this change. (3) Custodian of master document shall make above revision and furnish revised document. b. ACTIVITY AUTHORIZED TO APPROVE CHANGE FOR GOVERNMENTDSCC-VAI c. TYPED

19、NAME (First, Middle Initial, Last)ROBERT HEBER d. TITLECHIEF, INTERCONNECTION DEVICES e. SIGNATURERobert M. Heber f. DATE SIGNED (YYMMDD) 02-02-01 15a. ACTIVITY ACCOMPLISHING REVISIONDSCC-VAI b. REVISION COMPLETED (Signature)Ron Gary c. DATE SIGNED (YYMMDD)02-02-01 DD Form 1695, APR 92 Previous edit

20、ions are obsolete Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-REVISIONS LTR DESCRIPTION DATE APPROVED E Correct jamnut mount part numbers. Changes in accordance with NOR 5935-R002-94. 17 November 1993 Randy Larson F Add new source of supply, CAGE

21、 95077. Editorial changes throughout. 24 May 1994 Charles Koeller (acting) G Fig 1, redrawn for clarity, both pages. Page 2; .440 max. was .436 max. Page 3; made flat optional on TNC side. Temp. limits reduced for -3 parts. Max. insertion force for SMA was 3 pounds. Test pin diameters clarified. Add

22、ed new source for -3 parts, CAGE 34078. Change CAGE to 037Z3. 26 February 1998 Robert M. Heber H Part or Identifying Number (PIN), source update. 13 August 1998 Robert M. Heber J Part or Identifying Number (PIN), source update. 16 November 2001 Robert M. Heber Requirements of drawing 85017 are appli

23、cable. THE ORIGINAL FIRST PAGE OF THIS DRAWING HAS BEEN REPLACED. Prepared in accordance with MIL-STD-100 REV PAGE REV J J J J J J REV STATUS OF PAGES PAGE 1 2 3 4 5 6 PREPARED BY PMIC N/A Ron Gary DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO 43216-5000 CHECKED BY TITLE C. W. Koeller APPROVED BY R

24、. Heber ADAPTER, ELECTRICAL, COAXIAL, RADIOFREQUENCY, (BETWEEN SERIES SMA TO SERIES TNC) SIZE CAGE CODE 037Z3 DWG. NO. 85018 Original date of drawing 18 March 1985 A REV J PAGE 1 OF 6 AMSC N/A 5935-E619 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.Provided by IHSN

25、ot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. 037Z3 85018 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 A REV J PAGE 2 PINs 8501814FS-1 8501814FS-2 8501814FP-1 8501814FP-2 FIGURE 1. General configuration.Provided by IHSNot for Resa

26、leNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. 037Z3 85018 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 A REV J PAGE 3 PINs 8501814BS-3 or 8501814BP-3 Inches mm Inches mm Inches mm Inches mm .010 .093 .125 .204 .250 0.25 2.36 3.18 5.18 6.35 .

27、310 .320 .400 .415 .4373 7.87 8.13 10.16 10.54 11.11 .439 .440 .450 .500 .562 11.15 11.18 11.43 12.70 14.27 .647 .656 .750 1.07 1.31 16.43 16.66 19.05 27.2 33.3 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Unless otherwise specified, tolerances are .01

28、5 inch (0.38 mm). 4. All undimensioned pictorial configurations are for reference purposes only. FIGURE 1. General configuration - Continued.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. 037Z3 85018 DEFENSE SUPPLY CENTER, COL

29、UMBUS COLUMBUS, OH 43216-5000 A REV J PAGE 4 ENGINEERING DATA: Nominal impedance: 50 ohms. Frequency range: 0 to 15 GHz. Voltage rating: 335 V rms at sea level. 85 V rms at 70,000 feet. Operating temperature: -65C to +165C. (-55C to +160C for 8501814BP-3 and 8501814BS-3 because of O-ring material li

30、mits) Performance: Installation torque 7 to 10 inch-pounds for series SMA, 4 to 6 inch-pound for series TNC. REQUIREMENTS (requirements of drawing 85017 are applicable): Dimensions and configuration: See figure 1. Center contact retention: Axial force: 6 pounds minimum. Torque: Not applicable. Force

31、 to engage and disengage: Longitudinal force: Not applicable. Torque: 2 inch-pounds, maximum. Mating characteristics: Series SMA Series TNC Center contact conditioning Oversize test pin dia. (inches) .0375 +.0001/-.0000 .057 min (nonclosed entry contacts only) Pin finish (microinches) 16 - Insertion

32、 depth (inches) .030/.045 .125 min Number of insertions 3 1 Insertion force test (maximum test pin): Steel test pin dia. (inches) .0370+.0001/-.0000 .054 max. Pin finish (microinches) 16 16 Insertion force (pounds, maximum) 2 2 Insertion depth (inches, maximum) .050/.075 - Withdrawal force test (min

33、imum test pin): Steel test pin dia. (inches) .0355+.0000/-.0001 .052 max. Pin finish (microinches) 16 16 Insertion force (ounces, maximum) 1 2 Insertion depth (inches, maximum) .050/.075 - Permeability: 2.0; air = 1.0. Seal: Pressurized: Not applicable. Weatherproof: Not applicable. Provided by IHSN

34、ot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. 037Z3 85018 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 A REV J PAGE 5 VSWR: 1.05 + .008 F(GHz) at .5 to 12.4 GHz. 1.09 + .009 F(GHz) at 12.4 to 15 GHz. RF leakage (total): -65 dB min

35、imum, 2 to 3 GHz. RF Insertion loss: .18 dB maximum, 9 GHz. Dielectric withstanding voltage: Test voltage: 1,000 V rms, minimum, at sea level. Contact resistance (milliohms, maximum): Contact Initial After environment Center contact: 4.1 1/ 6.0 Outer contact: 2.2 Not applicable Vibration, high frequ

36、ency: Interruptions: 1 s maximum. Shock: MIL-STD-202, method 213, test condition I. Thermal shock: MIL-STD-202, method 107, test condition C. Moisture resistance: 200 megohms, minimum. Corona level: Voltage: 250 V, minimum. Altitude: 70,000 feet minimum. RF high potential withstanding voltage: RF vo

37、ltage: 1,000 volts, minimum. Frequency: 5 MHz, minimum. Part or Identifying Number (PIN): 8501814FS-1: For .125 inch diameter through holes. 8501814FS-2: Tapped holes to accommodate 3-56 UNF mounting screws. 8501814FP-1: For .125 inch diameter through holes. 8501814FP-2: Tapped holes to accommodate

38、3-56 UNF mounting screws. 8501814BP-3 and 8501814BS-3: Jamnut mount. _ 1/ Two center contacts must be mated to the center conductor under test; therefore doubling “center contact” resistance.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE C

39、ODE DWG NO. 037Z3 85018 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 A REV J PAGE 6 Supersession data: See table II. TABLE II. Superssion table. Preferred PIN Superseded PIN 8501814FS-1 8501814FS-2 85017/8501814FS 8501814FP-1 8501814FP-2 85017/8501814FP Approved sources of supply are list

40、ed herein. Additional sources will be added as they become available. The vendors listed on the requirements drawing have agreed to this drawing and a certificate of compliance has been submitted to DSCC-VAI. DSCC drawing PIN 1/ Vendor CAGE number Vendor reference PIN 8501814FS-1 00795 95077 2225000

41、A911-000 1102-0003 8501814FS-2 00795 95077 2225000A911-001 1102-0002 8501814BS-3* 95077 1134-0014 8501814FP-1 00795 95077 2225000K911-000 SF1102-6003 8501814FP-2 00795 95077 2225000K911-001 SF1102-6002 8501814BP-3* 95077 34078 SF1134-6014 ADT-2779-FF-004-02 1/ Parts must be purchased to this DSCC PI

42、N to assure that all performance requirements and tests are met. * NOTE: Part or Identifying Numbers (PINs) corrected from 8501814FS-3 and 85014FP-3 to 8501814BS-3 and 8501814BP-3 respectively to conform to the PIN structure of DSCC drawing 85017. Parts already manufactured and in stock to the previ

43、ous PINs need not be remarked. Vendor CAGE Vendor name number and address 00795 Delta Electronics 416 Cabot Street Beverly, MA 01915 34078 Midwest Microwave 6564 S. State Road Saline, MI 48176 95077 Soliton/Vector 3301 Electronics Way West Palm Beach, FL 33407 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-