DLA DSCC-DWG-85009 REV E-2008 DELAY LINES ACTIVE TWO DELAY LINES 14-PIN DIP TTL INTERFACED.pdf

《DLA DSCC-DWG-85009 REV E-2008 DELAY LINES ACTIVE TWO DELAY LINES 14-PIN DIP TTL INTERFACED.pdf》由会员分享，可在线阅读，更多相关《DLA DSCC-DWG-85009 REV E-2008 DELAY LINES ACTIVE TWO DELAY LINES 14-PIN DIP TTL INTERFACED.pdf（9页珍藏版）》请在麦多课文档分享上搜索。

1、 REVISIONS LTR DESCRIPTION DATE APPROVED A Added three sources for all dash numbers. 05 Sep 85 Ivan R. Jones B Added note 4 to figure 1. Eliminated references to MIL-D-23859 and replaced with references to MIL-PRF-83532. 19 Oct 87 Randy Larson C Added suggested sources of supply and changed requirem

2、ents for inspection of product for delivery. 05 Aug 88 Randy Larson D Changed paragraph 3.2. Changed two dimensions on figure 1 and added note 5. Added paragraphs 3.26 and 3.30. Deleted vendor CAGE 56289. Editorial changes throughout. 11 Jun 93 D. Moore E Incorporated boilerplate updates. 17 Jun 08

3、Michael A. Radecki Prepared in accordance with ASME Y14.100 Source control drawing REV E E E E E E E E E REV STATUS OF PAGES PAGES 1 2 3 4 5 6 7 8 9 PMIC N/A PREPARED BY Randy Larson DESIGN ACTIVITY DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OH 45444-5000 CHECKED BY Randy Larson APPROVED BY Ivan R. J

4、ones TITLE DELAY LINES, ACTIVE, TWO DELAY LINES, 14-PIN DIP, TTL INTERFACED SIZE A CODE IDENT. NO. 14933 DWG NO. 85009 Original date of drawing 30 Aug 85 REV E PAGE 1 OF 9 AMSC N/A 5999-E219CURRENT DESIGN ACTIVITY CAGE CODE 037Z3 DEFENSE LOGISTICS AGENCY DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO

5、 43218-3990 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-CODE IDENT NO. 14933 DWG NO. 85009 DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A REV E SHEET 2 1. SCOPE 1.1 Scope. This drawing describes the requirements for a family of 14-pin dela

6、y lines with two delay lines per package. 1.2 Part or Identifying Number (PIN). The complete PIN shall be as shown in the following example: 85009 -01 Drawing number Dash number 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3 and 4 of this specif

7、ication. This section does not include documents cited in other sections of this specification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requiremen

8、ts of documents in sections 3 and 4 of this specification, whether or not they are listed. 2.2 Government documents. 2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise sp

9、ecified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-DTL-31000 - Technical Data Packages. MIL-PRF-83532 - Delay Lines, Active, General Specification for. DEPARTMENT OF DEFENSE STANDARD MIL-STD-202 - Test Methods, Standard El

10、ectronic and Electrical Component Parts. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or http:/assist.daps.dla.mil/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.3 Order of precedence. In

11、 the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing shall take precedence. Nothing in this drawing, however, shall supersede applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Drawing prec

12、edence. This drawing takes precedence over documents referred to herein and shall be interpreted in accordance with MIL-DTL-31000. 3.2 Case material. The case material shall be molded diallyl phthalate or encapsulated epoxy and shall be in accordance with MIL-PRF-83532. 3.3 Design and dimensions. Th

13、e design and dimensions shall be in accordance with figure 1. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-CODE IDENT NO. 14933 DWG NO. 85009 DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A REV E SHEET 3 FIGURE 1. Design and dimensions. Inch

14、es mm .012 0.30 .018 0.46 .060 1.52 .100 2.54 .110 2.79 .175 4.45 .195 4.95 .300 7.62 .510 12.95 .810 20.57 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-CODE IDENT NO. 14933 DWG NO. 85009 DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A REV E

15、 SHEET 4 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Unless otherwise specified, tolerance is .005 (0.13 mm). 4. Location, shape, and dimensions of standoffs are optional. Height shall be as indicated. 5. Leads shall be free of case meniscus a

16、nd other foreign material and shall be solderable for a minimum of .010 inch (0.25 mm) above the seating plane of the delay line. FIGURE 1. Design and dimensions - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-CODE IDENT NO. 14933 DWG NO

17、. 85009 DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A REV E SHEET 5 3.4 Terminals. The terminal material and finish shall be in accordance with MIL-PRF-83532. 3.5 Temperature coefficient of delay. The temperature coefficient of delay shall be +1200 ppm/C maximum. 3.6 Total delay time. The to

18、tal delay time shall be in accordance with table I. TABLE I. PINs and delay times. DESC PIN 85009- Delay per line (ns) DESC PIN 85009- Delay per line (ns) 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 22 23 24 25 26 27 28 29

19、30 31 32 33 34 35 36 37 38 39 40 41 42 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 125 150 175 200 225 250 3.7 Delay tolerance. The delay tolerance shall be 2 ns or 5 percent, whichever is greater (at +25C with VCC= 5.0 V dc). 3.8 Rise time. The rise time shall be 4 ns maximum. 3.9 Pulse width. Th

20、e minimum input pulse width shall be 100 percent of the total delay. 3.10 Supply voltage (VCC). The supply voltage shall be 4.75 V dc to 5.25 V dc. 3.11 Supply current: a. Constant “0“ in 60 mA maximum. b. Constant “1“ in 20 mA maximum. Provided by IHSNot for ResaleNo reproduction or networking perm

21、itted without license from IHS-,-,-CODE IDENT NO. 14933 DWG NO. 85009 DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A REV E SHEET 6 3.12 Logic 1 input. The logic 1 input shall be 50 A maximum at 2.4 volts or 1.0 mA maximum at 5.5 volts. 3.13 Logic 0 input. The logic 0 input shall be -2 mA maxi

22、mum at 0.8 volt maximum. 3.14 Logic 1, VOUT. The logic 1, VOUTshall be 2.4 volts minimum. 3.15 Logic 0, VOUT. The logic 0, VOUTshall be 0.4 volt minimum. 3.16 Fan-out. The fan-out shall be 10 maximum (each delay line is capable of driving 10 TTL). 3.17 Thermal shock. The thermal shock test shall be

23、in accordance with method 107, test condition A, of MIL-STD-202, 5 minutes at temperature extremes and as specified in MIL-PRF-83532. 3.18 Seal. The seal test shall be in accordance with MIL-PRF-83532. 3.19 Terminal strength. The terminal strength test shall be in accordance with method 211, test co

24、ndition C of MIL-STD-202, and as specified in MIL-PRF-83532. 3.20 Vibration. The vibration test shall be in accordance with method 204, test condition B of MIL-STD-202, and as specified in MIL-PRF-83532. 3.21 Shock. The shock test shall be in accordance with method 213, test condition D of MIL-STD-2

25、02 and as specified in MIL-PRF-83532. 3.22 Immersion. The immersion test shall be in accordance with method 104, test condition A of MIL-STD-202, and as specified in MIL-PRF-83532. 3.23 Moisture resistance. The moisture resistance test shall be as specified in MIL-PRF-83532. 3.24 Solderability. The

26、solderability test shall be as specified in MIL-PRF-83532. 3.25 Resistance to solvents. The resistance to solvents test shall be as specified in MIL-PRF-83532. 3.26 Check for internal shorts. When a test signal is applied to any input, a delay signal should be detected at the output for that line on

27、ly. For example, when input 1 is tested, there shall be no signal detected at output 2. Both inputs shall be checked in this manner to ensure there are no shorts between lines. 3.27 Temperature range. The operating temperature range shall be -55C to +125C. 3.28 Recycled, recovered, or environmentall

28、y preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible, provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs. 3.29 Manufacturer eli

29、gibility. To be eligible for listing as an approved source of supply, a manufacturer shall be listed on the MIL-PRF-83532 Qualified Product List for at least one part, or perform the Group A and Group B inspections specified herein on a sample of parts agreed upon by the manufacturer and DSCC-VA. 3.

30、30 Certificate of compliance. A certificate of compliance shall be required from manufacturers requesting to be an approved source of supply. 3.31 Pure tin. The use of pure tin, as an underplate or final finish is prohibited both internally and externally. Tin shall be alloyed with a minimum of 3 pe

31、rcent lead, by mass (see 6.3). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-CODE IDENT NO. 14933 DWG NO. 85009 DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A REV E SHEET 7 3.32 Marking. Marking shall be in accordance with MIL-PRF-83532, exc

32、ept that the military PIN shall be as specified in 1.2. 3.33 Workmanship. Parts shall be free of flash pits, voids, excessive mold marks, and other defects that could affect the performance of the parts. Visible parting line is acceptable. 4. QUALITY ASSURANCE PROVISIONS 4.1 Sampling and inspection.

33、 Inspection of product for delivery shall consist of compliance with the group A inspection for level A of MIL-PRF-83532. 5. PACKAGING 5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When packaging of materiel is to be per

34、formed by DoD or in-house contractor personnel, these personnel need to contact the responsible packaging activity to ascertain packaging requirements. Packaging requirements are maintained by the Inventory Control Points packaging activities within the Military Service or Defense Agency, or within

35、the military services system commands. Packaging data retrieval is available from the managing Military Departments or Defense Agencys automated packaging files, CD-ROM products, or by contacting the responsible packaging activity. 6. NOTES 6.1 Intended use. Devices conforming to this drawing are in

36、tended for use when military specifications do not exist and qualified military devices that will perform the required function are not available for OEM application. 6.2 Ordering data. The acquisition document should specify the following as a minimum: a. Complete DESC PIN (see 1.2). b. Requirement

37、 for the manufacturer to deliver one copy of the quality conformance inspection data with each shipment of parts. c. Requirement for the manufacturer to notify the acquiring activity in the event of a change in product. d. Requirements for packaging and packing. 6.3 Tin whisker growth. The use of al

38、loys with tin content greater than 97 percent, by mass, may exhibit tin whisker growth problems after manufacture. Tin whiskers may occur anytime from a day to years after manufacture and can develop under typical operating conditions, on products that use such materials. Conformal coatings applied

39、over top of a whisker-prone surface will not prevent the formation of tin whiskers. Alloys of 3 percent lead, by mass, have shown to inhibit the growth of tin whiskers. For additional information on this matter, refer to ASTM-B545 (Standard Specification for Electrodeposited Coatings of Tin). 6.4 Us

40、ers of record. Coordination of this document for future revisions is coordinated only with the approved source(s) of supply and the users of record of this document. Requests to be added as a recorded user of this drawing may be achieved online at mailto:relaydla.mil or if in writing to: Defense Sup

41、ply Center, Columbus, ATTN: DSCC/VAT, Post Office Box 3990, Columbus, OH 43218-3990 or by telephone (614) 692-4481 or DSN 850-4481. 6.5 Approved source(s) of supply. Approved source(s) of supply are listed herein. Additional sources will be added as they become available. Assistance in the use of th

42、is drawing may be obtained online at mailto:relaydla.mil, or by contacting Defense Supply Center, Columbus, ATTN: DSCC-VAT, Post Office Box 3990, Columbus, OH 43218-3990 or by telephone (614) 692-4481 or DSN 850-4481. Provided by IHSNot for ResaleNo reproduction or networking permitted without licen

43、se from IHS-,-,-CODE IDENT NO. 14933 DWG NO. 85009 DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A REV E SHEET 8 Similar vendor PIN and CAGE code 1/ DESC PIN 85009- CAGE 00222 CAGE 22519 CAGE 16714 01 02 03 04 05 96-75-1 96-75-2 96-75-3 96-75-4 96-75-5 MDU2-8513-1 MDU2-8513-2 MDU2-8513-3 MDU2-

44、8513-4 MDU2-8513-5 DSP009-01 DSP009-02 DSP009-03 DSP009-04 DSP009-05 06 07 08 09 10 11 12 13 14 15 96-75-6 96-75-7 96-75-8 96-75-9 96-75-10 96-75-11 96-75-12 96-75-13 96-75-14 96-75-15 MDU2-8513-6 MDU2-8513-7 MDU2-8513-8 MDU2-8513-9 MDU2-8513-10 MDU2-8513-11 MDU2-8513-12 MDU2-8513-13 MDU2-8513-14 MD

45、U2-8513-15 DSP009-06 DSP009-07 DSP009-08 DSP009-09 DSP009-10 DSP009-11 DSP009-12 DSP009-13 DSP009-14 DSP009-15 16 17 18 19 20 21 22 23 24 25 26 96-75-16 96-75-17 96-75-18 96-75-19 96-75-20 96-75-21 96-75-22 96-75-23 96-75-24 96-75-25 96-75-26 MDU2-8513-16 MDU2-8513-17 MDU2-8513-18 MDU2-8513-19 MDU2-

46、8513-20 MDU2-8513-21 MDU2-8513-22 MDU2-8513-23 MDU2-8513-24 MDU2-8513-25 MDU2-8513-26 DSP009-16 DSP009-17 DSP009-18 DSP009-19 DSP009-20 DSO009-21 DSP009-22 DSP009-23 DSP009-24 DSP009-25 DSP009-26 27 28 29 30 31 96-75-27 96-75-28 96-75-29 96-75-30 96-75-31 MDU2-8513-27 MDU2-8513-28 MDU2-8513-29 MDU2-

47、8513-30 MDU2-8513-31 DSP009-27 DSP009-28 DSP009-29 DSP009-30 DSP009-31 See footnote at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-CODE IDENT NO. 14933 DWG NO. 85009 DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A REV E SHEET

48、9 Similar vendor PIN and CAGE code 1/ DESC PIN 85009- CAGE 00222 CAGE 22519 CAGE 16714 32 33 34 35 36 96-75-32 96-75-33 96-75-34 96-75-35 96-75-36 MDU2-8513-32 MDU2-8513-33 MDU2-8513-34 MDU2-8513-35 MDU2-8513-36 DSP009-32 DSP009-33 DSP009-34 DSP009-35 DSP009-36 37 38 39 40 41 42 96-75-37 96-75-38 96-75-39 96-75-40 96-75-41 96-75-42 MDU2-8513-37 MDU2-8513-38 MDU2-8513-39 MDU2-8513-40 MDU2-8513-41 MDU2-8513-42 DSP009-37 DSP009-38 DSP009-39 DSP009-40 DSP009-41 DSP009-42 1/ Parts must be purchased to the DSCC PIN to assure t