DLA DSCC-DWG-01003-2000 CONNECTORS PLUG ELECTRICAL REAR RELEASE CRIMP CONTACT AN TYPE《某类型卷曲接触电工插头连接器》.pdf

《DLA DSCC-DWG-01003-2000 CONNECTORS PLUG ELECTRICAL REAR RELEASE CRIMP CONTACT AN TYPE《某类型卷曲接触电工插头连接器》.pdf》由会员分享，可在线阅读，更多相关《DLA DSCC-DWG-01003-2000 CONNECTORS PLUG ELECTRICAL REAR RELEASE CRIMP CONTACT AN TYPE《某类型卷曲接触电工插头连接器》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、REVISIONSLTR DESCRIPTION DATE APPROVEDPrepared in accordance with MIL-STD-100REVPAGEREVREV STATUSOF PAGES PAGE 1 2 3PREPARED BYPMIC S Abdo AbdouniDEFENSE SUPPLY CENTER, COLUMBUSCOLUMBUS, OHIO 43216-5000CHECKED BY TITLEAbdo AbdouniAPPROVED BYRobert M. HeberCONNECTORS, PLUG, ELECTRICAL,REAR RELEASE, C

2、RIMP CONTACT, AN TYPESIZE CAGE CODE037Z3 DWG. NO. 01003Original date ofdrawing15 December 2000A REV PAGE 1OF 3AMSC N/A 5935-E644DISTRIBUTION STATEMENT A . Approved for public release; distribution is unlimited.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from

3、IHS-,-,-SIZE CAGE CODE DWG NO.037Z3 01003DEFENSE SUPPLY CENTER, COLUMBUSCOLUMBUS, OH 43216-5000 AREV PAGE 2NOTES:1. Dimensions are in inches.2. Unless otherwise specified, tolerance is .016.3. MIL-C-5015 Crimp contact, front and rear release connectors and solder contact connectors are intermateable

4、.4. Unless otherwise shown, corresponding features of pin and socket contact connectors are identical.5. Extraction tool M81969/29-01shall be used to remove contacts that are crimped to MIL-W-25038 or MIL-DTL-27500 fire zone wire.6. For insert arrangements, see MIL-STD-1651.7. Contact size 16 and 12

5、 only are to be used with this connector.8. For details of connector front and rear end configurations, see MIL-DTL-5015.9. Class K connectors with electroless nickel finish are inactive for new design after 25 April 1974.10. Class U connectors are inactive for new design after 23 March 1976, use cl

6、ass L for new design.FIGURE 1. General configuration .Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO.037Z3 01003DEFENSE SUPPLY CENTER, COLUMBUSCOLUMBUS, OH 43216-5000 AREV PAGE 3REQUIREMENTS: (MS3456 is applicable).Design and c

7、onstruction, electrical, mechanical and environmental requirements shall be in accordance withMIL-DTL-5015 and MS3456, with the following exception : See figure 1.Part or Identifying Number (PIN) example (DD01003W14S-6S):DD01003 W 14 -5 S WBasic prefixClassMaterial designator.S Stainless SteelT Ferr

8、ous alloy with cadmium plate.Leave blank for Aluminum alloy and wrought Aluminum.Shell sizeInsert arrangementContact designatorAlternate insertPosition W, X, Y or Z.Leave blank for normal position.DSCC Drawing PIN Vendor CAGE Number Vendor Similar PINDD01003W14S-6S 14283 3456W14S16SProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-