DLA A-A-59591-2000 CLOTH BUNTING COTTON MERCERIZED [Superseded DLA CCC-C-439 G CANC NOTICE 1 DLA CCC-C-439 G DLA CCC-C-439 F VALID NOTICE 1 DLA CCC-C-439 F DLA CCC-C-439 E DLA CCC-.pdf

《DLA A-A-59591-2000 CLOTH BUNTING COTTON MERCERIZED [Superseded DLA CCC-C-439 G CANC NOTICE 1 DLA CCC-C-439 G DLA CCC-C-439 F VALID NOTICE 1 DLA CCC-C-439 F DLA CCC-C-439 E DLA CCC-.pdf》由会员分享，可在线阅读，更多相关《DLA A-A-59591-2000 CLOTH BUNTING COTTON MERCERIZED [Superseded DLA CCC-C-439 G CANC NOTICE 1 DLA CCC-C-439 G DLA CCC-C-439 F VALID NOTICE 1 DLA CCC-C-439 F DLA CCC-C-439 E DLA CCC-.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、I INCH-POUNDI A-A-59591 May 24,2000 Supersedes May 15,1990 CCC-C-439G COMMERCIAL ITEM DESCRIPTION CLOTH, BUNTING, COTTON, MERCERIZED The General Services Administration has authorized the use of this commercial item description in preference to Federal Specification CCC-C-439 1. SCOPE 1.1 signal, se

2、maphore, ensign (including U.S. flag), and other types of flags. This specification covers cotton bunting, which is primarily used in the manufacture of CLASSIFICATION This specification covers one type of cotton bunting. SALIENT CHARACTERISTICS 3.1 Yarn. The yam shall be made from cotton which has

3、been carded, drawn, spun and twisted into two-ply yarn for both warp and filling. 3.2 Color. The color of the finished cloth shall be as specified (see 6.2) 3.2.1 Matching. The color of the finished cloth, shall match the standard sample when viewed under filtered tungsten lamps that approximate art

4、ificial daylight and that have a correlated color temperature of 7500 f 200 K, with illumination of 100 f 20 foot candles, and shall be a good match to the standard sample under incandescent lamplight at 2300 f 200 K. When no standard sample available the finished cloth shall match the applicable co

5、lor card (see 6.2), either by cable number or names. Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: Defense Supply Center Philadelphia, Clothing and Textiles Directorate, Attn.: DSCP-COCT, 700

6、Robbins Ave., Philadeldia PA 191 11-5092. AMSC NIA FSC 8305 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59591 Weight, ounces per square yard (minimum) 45 3.2.2

7、Colorfastness. The finished cloth shall show fastness to light, water and salt water and soap equal to or better than the standard sample or equal to or better than a rating of 3.5, on the AATCC Gray Scale for Change in Color. The fiished cloth shall show fastness to crocking equal to or better than

8、 the standard sample or shall have an AATCC Chromatic Transference Scale rating not lower than 3.5. Testing shall be as specified in 5.3. Yams per inch Breaking Strength (minimum) Pounds (minimum) Warp Filling Warp Filling 31 3n 5n 5n 3.2.3 Labile sulfur. The use of dyes and compounds containing ele

9、mentary sulfur capable of oxidation to sulfuric acid is prohibited. The dyestuff shall be chosen and applied so that the dyed and finished cloth shall contain no more labile sulfur than shown by the standard sample when tested as specified in 5.3. When no standard sample is available, the finished c

10、loth shall show no more than a slight trace of labile sulfur when tested as specified in 5.3. 3.3 Physical requirements. The finished cloth shall conform to the requirements specified in table I when tested as specified in 5.3. 3.3.1 Weave. The weave shall be plain. 3.3.2 Width. The minimum width ex

11、clusive of selvages shall be 37-1/2 inches for the Military services and 35-3/4 inches for Civil agencies (see 6.1). 3.4 Finish. The cloth shall be mercerized. 3.5 m. The pH value of the water extract of the dyed and finished cloth shall be not less than 5.0 and not greater than 8.5 when tested as s

12、pecified in 5.3. 3.6 Length and put-up. Unless otherwise specified (see 6.1), the cloth shall be furnished in continuous pieces of not less than 35 yards and shall be put-up in rolls or flat folded-pieces (bolts) as specified in 5.2. 3.7 Fiber identification. Each roll or folded piece shall be label

13、ed, ticketed, or invoiced for fiber content in accordance with the Textile Fiber Products Identification Act. REGULATORY REQUIREMENTS. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59591 4.1 Recycled, recovered, or environmentally preferable

14、materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible in accordance with paragraph 23.403 of the Federal Acquisition Regulation Act (FAR), provided that the material meets or exceeds the operational and maintenance requirements and prom

15、otes economically advantageous life cycle costs. 5. QUALITY ASSURANCE PROVISIONS 5.1 Product conformance. The products provided shall meet the salient characteristics of this commercial item description and conform to the producers own drawings, specifications, standards and quality assurance practi

16、ces. The Government reserves the right to require proof of such conformance. 5.2 Preservation, packing and marking. The preservation, packing and marking shall be as specified in the contract or order. 5.3 End item testing. The cloth shall be tested for the characteristics listed in table II. The ph

17、ysical and chemical values specified in section 3, except where otherwise specified, apply to the results of the determinations made on a sample unit for test purposes as specified in the applicable test method. All test reports shall contain the individual values utilized in expressing the final re

18、sult. The sample unit for test purposes shall be 1-1/2 continuous yards full width of the finished cloth. The lot shall be unacceptable if one or more units fail to meet any requirement specified. The sample size shall be as follows: Lot size (yards) Sample size 800 or less 2 801 up to and including

19、 22,000 3 22,001 and over 5 TABLE II. End item tests Requirement Test Characteristic paragraph method Identification of cotton 3.1 AATCC20 1/ Yarn ply 3.1 Visual 2/ Colorfastness to: Crocking 3.2.2 AATCC 8 TABLE II. End item tests (contd) 3 Provided by IHSNot for ResaleNo reproduction or networking

20、permitted without license from IHS-,-,-A-A-59591 Characteristic Requirement paragraph Test method Light Water Salt water and soap Weight C Yams per inch: warp Filling Breaking strength: warp Filling Weave Mercerization examination for swelling of cotton fibers Labile sulfur PH 3.2.2 3.2.2 3.2.2 3.3

21、3.3 3.3 3.3 3.3 3.3.1 3.4 3.2.3 3.5 AATCC-16 OPT A AATCC-107 3/ AATCC- 106 ASTM-D-3776 OPT ASTM-D-3775 ASTM-D-3775 ASTM-D-5034 ASTM-D-5034 Visual 2/ Microscopic 1/ 5.3.1 AATCC-8 1 1/ acceptable for the stated requirement. Unless otherwise specified, a certificate of compliance shall be submitted and

22、 will be 2/ “fail. One determination shall be made from each sample unit and results reported as “pass or 3/ Except the time shall be one hour 5.3.1 Presence of Labile sulfur In the determination of presence of labile sulfur in textile materials with lead acetate, two 1 SO f 0.01 gram samples from e

23、ach material submitted for evaluation shall be tested. Each of the two samples shall be cut into very small pieces and placed into separate test tubes. The samples shall be submersed in a stannous chloride solution that contains 100 grams of stannous chloride crystals ACS in 100 milliliters of hydro

24、chloric acid ACS (35 percent concentration) and 50 milliliters of distilled water. A filter paper wet out with a 5.0 percent lead acetate solution shall be placed over top of the test tube. The lead acetate solution contains 5.0 grams of lead acetate CP reagent grade and enough distilled water to ma

25、ke up a 100 milliliter solution; if the solution is not clear, add a few drops (one at a time) of glacial acetic acid until the solution is clear. The test tube containing the textile sample, stannous chloride and wet filter paper shall be heated over a low flame until the solution is boiling. The s

26、olution should not be heated for more than 15 seconds. A brown to black stain on the filter paper should be 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-evaluated as follows: Free - The filter paper shows no discoloration or staining of any kind

27、. Slight - The filter paper shows a light tan to light brown discoloration stain. Moderate - The filter paper shows a dark brown discoloration stain. Severe - The filter paper shows a black color stain. 5.3.2 Yard-by-yard examination. Each roll or flat-folded piece in the sample shall be examined on

28、 one side only. When the total yardage in the roll or flat-folded piece does not exceed 100 yards, the entire yardage in the roll or flat-folded piece shall be examined. When the total yardage in the roll or flat-folded piece exceeds 1 O0 yards, only 1 O0 yards shall be examined. The cloth shall be

29、examined for the following defects: Any hole, cut tear, mend, burn, smash, misweave, missing yam, or weakening defect such as smash, loose slub, shade padbar, stamping marks, or color not as specified. Poor dye penetration, mottled, streaky, or cloudy. Objectionable odor, baggy, ridgy, or wavy cloth

30、. Width less than specified, uneven weaving, multiple floats or skips Yinch or more in either the warp or the filling direction of the fabric. fabric edges rolled, folded, doubled scalloped or wavy., any spot or stain fabric not clean 5.3.3 Length examination. During the yard-by-yard examination, ea

31、ch roll or flat-folded piece in the sample shall be examined for length. Any length found to be less than the minimum specified or more than 2 yards less than the Length marked on the ticket shall be considered a defect with respect to length 5.3.4 Shade examination. During the yard-by-yard examinat

32、ions, each roll or flat-folded piece in the sample shall be examined for shade. Any roll or flat-folded piece in the sample off shade or shaded side to side, side to center, or end to end shall be cause for rejection of the entire lot represented by the sample. 5.3.5 Marking examination. During the

33、yard-by-yard examination, each roll or flat-folded piece shall be examined for marking. The lot shall be unacceptable if two or more rolls or flat- folded pieces in the sample are not labeled, ticketed, or invoiced in accordance with the Textile Fiber Products Identification Act. 6. NOTES 5 Provided

34、 by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-(This section contains information of a general or explanatory nature that may be helpful, but is not mandatory.) 6.1 Acquisition requirements. Acquisition documents must specify the following: a. b. Color requ

35、ired (see 3.2). c. Width required (see 3.3.2). d. e. Title, number, and date of this specification. Length required if other than specified (see 3.9). Levels of put-up, preservation and packing (see 5.2). 6.2 Sample. For access to samples, address the contracting activity issuing the invitation for

36、bids or request for proposal. 6.3 Sources of Nongovernment Documents The following documents form a part of this specification to the extent specified herein. Unless a specific issue is identified, the issue in effect on date of invitation for bids or request for proposal shall apply. Federal Regula

37、tions Federal Trade Commission Rules and Regulations Under the Textile Fiber Products Identification Act (Application for copies should be addressed to the Federal Trade Commission, Washington, DC 20580.) Color Association of the United States Standard Color Card of America (Color cards may be avail

38、able from the Color Association of the United States Inc., 343 Lexington Avenue, New York, NY 10016. If color cards are not available from the Color Association, individual color samples may be obtained from the contracting activity or as directed by the contracting activity.) American Association o

39、f Textile Chemists and Colorists (AATCC) Chromatic Transference scale 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AATCC - 8 - Colorfastness to Crocking AATCC - 16 - Colorfastness to Light AATCC - 20 - Fiber Analysis, Qualitative AATCC - 61 - Co

40、lorfastness to Laundry, Home and Commercial: Accelerated AATCC - 8 1 - pH of the Water- Extract from Bleached Textiles AATCC - 106 - Colorfastness to Water: Sea AATCC - 107 - Colorfastness to Water (Application for copies should be addressed to the American Association of Textile Chemists and Colori

41、sts, 1 Davis Dr., P.O. Box 12215, Research Triangle ParkNC 27709-2215.) AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) PUBLICATION ASTM -D-3775 - Fabric Count of Woven Fabrics ASTM-D-3776 - Mass Per Unit Area (Weight) of Fabric ASTM-D-5034 - Breaking Force, and Elongation of Textile Fabrics (Appl

42、ication for copies should be addressed to American Society for Testing and Materials, 1 O0 Barr Harbour Drive, West Conshohocken, PA 19428) 6.4 Sources of Supply. Manufactures Whose Products are know to meet the requirements of this CID are listed below, but these manufactures may not produce all ty

43、pes; however, competition is not limited to these companies. ATD -America CO 135 Greenwood Ave. Wyncote Pa 19095- 1396 Fordham Textile Corp. 3 Terrace Circle 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Great Neck NY 11021-4161 West Point-Pepper

44、ell INC 4th AVE. and loth ST. P.O. Box 71 West Point GA 3 1833 MILITARY INTERESTS: ACTIVITIES : Custodians: Army- GL Navy- NU Air Force - 99 Review activities: Navy - MC Air Force - 11, 82 Army - IH, MD CIVIL AGENCY COORDINATING COM- NIST GSA -FSS JUS -FPI VA - OSS PREPARING ACTIVITY: DLA - CT (Project 8305-0791) 8 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-