DLA A-A-59414-2000 SIRENS OUTDOOR WARNING ELECTRONIC AND ELECTRIC-MOTOR-DRIVEN [Superseded DLA MIL-S-503 B CANC NOTICE 1 DLA MIL-S-503 B DLA MIL-S-503 A DLA JAN-S-503]《电子和电机驱动的户外警告.pdf

《DLA A-A-59414-2000 SIRENS OUTDOOR WARNING ELECTRONIC AND ELECTRIC-MOTOR-DRIVEN [Superseded DLA MIL-S-503 B CANC NOTICE 1 DLA MIL-S-503 B DLA MIL-S-503 A DLA JAN-S-503]《电子和电机驱动的户外警告.pdf》由会员分享，可在线阅读，更多相关《DLA A-A-59414-2000 SIRENS OUTDOOR WARNING ELECTRONIC AND ELECTRIC-MOTOR-DRIVEN [Superseded DLA MIL-S-503 B CANC NOTICE 1 DLA MIL-S-503 B DLA MIL-S-503 A DLA JAN-S-503]《电子和电机驱动的户外警告.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、Beneficial comments, recommendations, additions, deletions, clarifications, etc. and any data thatmay improve this document should be sent to: Defense Supply Center Richmond (DSCR), ATTN:DSCR-VBD, 8000 Jefferson Davis Highway, Richmond, VA 23297-5610.AMSC N/A FSC 6350DISTRIBUTION STATEMENT A. Approv

2、ed for public release; distribution is unlimited.INCH-POUNDA-A-5941422 May 2000 SUPERSEDINGMIL-S-503B28 April 1988COMMERCIAL ITEM DESCRIPTIONSIRENS, OUTDOOR WARNING,ELECTRONIC AND ELECTRIC-MOTOR-DRIVENThe General Services Administration has authorized the use of thiscommercial item description for a

3、ll federal agencies.1. SCOPE. This commercial item description (CID) covers electronic and electric-motor-drivenoutdoor warning sirens capable of providing 360-degree coverage. The sirens shall be complete withall controls and auxiliary equipment, and suitable for mounting roofs or other supporting

4、structureswithout additional protection from the weather.2. CLASSIFICATION. The sirens shall be of the following types, classes, styles, and sizes. The type,class, style, and size to be furnished shall be as specified (see 7.2(b).Type I - Electric-motor-driven vertical sirenType II - Electric-motor-

5、driven horizontal sirenType III - Electronic sirenClass 1 - UncodedClass 2 - CodedStyle A - OmnidirectionalStyle B - Rotating directionalSize - See table IProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-594142TABLE I Siren sizes.Size Sound pressu

6、re level, decibels at 100 feet01 100 10202 103 10503 106 10804 109 11105 112 11406 115 11707 118 12008 121 12309 124 12610 127 12911 130 13212 133 1353. SALIENT CHARACTERISTICS3.1 General requirements. The siren shall be new and one of the manufacturers current modelscapable of operation in accordan

7、ce with the requirements herein. All parts subject to wear, breakage,or distortion shall be accessible for adjustment, replacement, and repair. The sirens shall be electric-motor-driven or electronic, and shall be complete in all details. They shall be of rugged construction towithstand vibration an

8、d exposure to severe weather conditions without excessive deterioration and shallbe capable of operating after long periods of nonuse. The sirens shall be constructed so that dust,water, and condensation within the unit will be at a minimum. Openings shall be screened to prevent theentrance of anima

9、ls and larger insects.3.2 Components. The siren shall include, as a minimum, the following components:3.2.1 Housing. The motor-driven siren or electronic siren speaker housing shall be constructed ofpowder coat painted sheet metal, color-impregnated fiberglass, fiberglass-reinforced moldedpolycarbon

10、ate resin, or aluminum (electronic siren speakers only). For sheet metal, all joints shall beriveted or welded securely, except bolts that shall be used to fasten portions made removable forinspection and maintenance of the interior mechanism. Sheet metal screws shall not be used. Fiberglassand poly

11、carbonate housings shall be drilled and shall be securely bolted to the supporting framework.3.2.2 Mounting. A base shall be provided for mounting the siren on a flat, horizontal surface; orbrackets for a slant roof or pole mount.3.2.3 Fan and stator (motor-driven sirens only). The fan and stator fo

12、r motor-driven sirens shall bemade of aluminum. The fan and other rotating parts of the siren shall be in static and dynamic balance. The fan shall be fastened securely to the motor shaft and a key shall be used to prevent slipping. Bafflesshall be provided within the housing, or the design of the s

13、tator and housing shall be such that the inputair is prevented from mixing with the output air.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-5941433.2.4 Code transmitter. The controls for class 2 coded siren shall include a code transmitter sui

14、tablefor the transmission of coded signals as specified (see 7.2(c).3.2.5 Electrical system. Unless otherwise specified (see 7.2(d), the electrical system shall conform tothe American National Standards Institute /National Fire Protection Association (ANSI/NFPA) 79,“Electrical Standard for Industria

15、l Machinery“ (DoD adopted).3.2.6 Electric motors. The motor for an electric-motor-driven siren shall have sealed and permanentlylubricated ball or roller bearings, shall be energy efficient, and shall conform tothe National Electrical Manufacturers Association (NEMA) MG-1, “Motors and Generators“ (D

16、oDadopted), and Underwriters Laboratories (UL) 674, “Electric Motors and Generators for use inDivision 1 Hazardous (Classified) Locations“ (DoD adopted). The motor shall be suitable for operationon an electric circuit with voltage (AC or DC), frequency, and phase (single or three-phase) as specified

17、(see 7.2(e).3.2.6.1 Control cabinets. Control cabinets for motor starters or electronic packages shall be of theproper size and suitable for the specific application, and shall conform to NEMA ICS 6, “IndustrialControls and Systems: Enclosures“ (DoD adopted). Unless otherwise specified (see 7.2(f),

18、theenclosure shall conform to NEMA type 1 for indoor mounting or type 3R for outdoor mounting, asdefined by NEMA 250, “Enclosures for Electrical Equipment (1000 Volts Maximum)“ (DoD adopted).3.3 Performance. Unless otherwise specified (see 7.2(g), the siren shall meet the sound pressure level(SPL) r

19、equirements shown in table II when tested in accordance with section 5.3 through 5.3.3.TABLE II Performance requirements.Size Minimum sound pressure level at 100 feet, decibels01 10002 10303 10604 10905 11206 11507 11808 12109 12410 12711 13012 1334. REGULATORY REQUIREMENTS4.1 Recovered materials. T

20、he offeror/contractor is encouraged to use recovered materials to themaximum extent practicable, in accordance with paragraph 23.403 of the Federal AcquisitionRegulation (FAR).Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-5941444.2 Environmenta

21、l protection. The item shall meet all applicable Environmental Protection Agency(EPA) restrictions in effect on the date of the contract. These regulations apply to the emission ofmaterials hazardous to the environment or the users health and shall be adhered to during themanufacturing, service, tra

22、nsportation, storage, and operation/use of the item.5. PRODUCT CONFORMANCE PROVISIONS5.1 Product conformance. The products provided shall meet the salient characteristics of thiscommercial item description, conform to the producers own drawings, specifications, standards, andquality assurance practi

23、ces, and be the same product offered for sale in the commercial marketplace. The government reserves the right to require proof of such conformance.5.2 Inspection. The siren shall be inspected to determine compliance with all requirements specified inthis CID.5.3 Testing. Unless otherwise specified

24、(see 7.2(h), the siren shall be tested in accordance withsections 5.3.1 through 5.3.4.5.3.1 Test setup and conditions. Unless otherwise specified (see 7.2(i), the manufacturer shallconduct all tests required by the Government. The manufacturer shall provide test instruments andequipment with calibra

25、tion traceable to National Institute of Standards and Technology (NIST) and shallprovide certification of calibration as specified (see 7.2(j). Unless otherwise specified (see 7.2(k), thesiren shall be tested in accordance with environmental conditions specified in ANSI S12.14, “Methodsfor the Field

26、 Measurement of the Sound Output of Audible Public Warning Devices Installed at FixedLocations Outdoors“.5.3.2 Operational test. The siren shall be operated in accordance with the manufacturers standardoperating procedures. Proper operation of all controls and features shall be verified during the t

27、rialperiod.5.3.3 Performance tests. The siren shall be tested for conformance with section 3.3 in accordance withANSI S12.14.5.3.4 Optional tests. Optional tests shall be conducted as specified (see 7.2(l).5.4 Acceptance. Unless otherwise specified (see 7.2(m), preliminary and final acceptance tests

28、 shallbe conducted at the manufacturers site. The results of the SPL tests shall be compared with therequirements shown in table II. Failure of the siren to meet the requirements shown in table II shall because for rejection.Provided by IHSNot for ResaleNo reproduction or networking permitted withou

29、t license from IHS-,-,-A-A-5941456. PACKAGING6.1 Preservation, packing, and marking. For acquisition purposes, the sirens shall be preserved,packed, and marked as specified in the acquisition order (see 7.2(n).7. NOTES7.1 Sources of documents.7.1.1 FAR. The FAR may be obtained from the Superintenden

30、t of Documents, U.S. GovernmentPrinting Office, Washington, DC 20402-0001.7.1.2 ANSI standards. Copies of ANSI standards may be obtained from the American NationalStandards Institute, 11 West 42nd Street, New York, NY 10036.7.1.3 ANSI/NFPA standards. Copies of NFPA standards may be obtained from the

31、 National FireProtection Association, 1 Batterymarch Park, Quincy, MA 02269-9101.7.1.4 UL standards. Copies of UL standards may be obtained from Underwriters Laboratories Inc.,333 Pfingsten Road, Northbrook, IL 60062.7.2 Ordering data. Acquisition documents must specify the following:a. Title, numbe

32、r, and date of this documentb. Type, class, style, and size of siren required (see 2)c. Code transmitter requirements, as specified (see 3.2.4)d. Electrical requirements, if different (see 3.2.5)e. Type motor, as specified (see 3.2.6)f. Type enclosure, if different (see 3.2.6.1)g. Performance, if di

33、fferent (see 3.3)h. Testing, if different (see 5.3)i. Test responsibility, if different (see 5.3.1)j. Certification of calibration, as specified (5.3.1)k. Test environmental conditions, if different (see 5.3.1)l. Optional tests, as specified (see 5.3.4)m. Acceptance tests site, if different (see 5.4

34、)n. Packaging requirements (see 6.1)Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-5941467.3 Part or identification number (PIN). The following part or identification numbering procedure is forgovernment purposes and does not constitute a requir

35、ement for the contractor.MILITARY INTERESTS:CIVIL AGENCYCOORDINATING ACTIVITY:Custodians:Army - CR4Navy - YDAir Force - 99GSA - 7FXEReviewers:Army - EA, MINavy - MCAir Force - 82Preparing activity:DLA - GS(Project 6350-0226)Size: See table IAA59414 X X X XXCID numberType: A - Type I - Electric-motor-driven vertical sirenB - Type II - Electric-motor-driven horizontal sirenC - Type III - Electric sirenStyle: A - OmnidirectionalB - Rotating directionalClass: 1 - Uncoded2 - CodedProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-