DLA A-A-55615-1995 SHIELD EXPANSION (WOOD SCREW AND LAG BOLT SELF-THREADING ANCHORS)《扩展护罩(自动穿线壁锚的木螺钉及木螺栓)》.pdf

《DLA A-A-55615-1995 SHIELD EXPANSION (WOOD SCREW AND LAG BOLT SELF-THREADING ANCHORS)《扩展护罩(自动穿线壁锚的木螺钉及木螺栓)》.pdf》由会员分享，可在线阅读，更多相关《DLA A-A-55615-1995 SHIELD EXPANSION (WOOD SCREW AND LAG BOLT SELF-THREADING ANCHORS)《扩展护罩(自动穿线壁锚的木螺钉及木螺栓)》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、A-A-55bb5 m 9999974 02b7992 92T m INCH-POUNDJ A-A-55615 19 JULY 1995 COMMERCIAL ITEM DESCRIPTION SHIELD, EXPANSION (WOOD SCREW AND LAG BOLT SELF-THREADING ANCHORS) The General Services Administrations has authorized the use of this commercial item description for all federal agencies. 1. SCOPE. This

2、 Commercial Item Description (CID) covers wood screw and lag bolt self-threading anchors for use in attaching equipment and fixtures to masonry. 2. SALIENT CHARACTERISTICS. 2.1 Self-Threading Anchor Configuration. Beneficial comments, recommendations, additions, deletions, clarifications, etc and da

3、ta which may improve this document should be sent to: Defense Industrial Supply Center, ATTN: DISC-ECB. 700 Robbins Avenue. Philadelphia, PA 191 11 -5096. ASMC N/A 1 of 2 FSC 5340 DISTRIBUTION STATEMENT A. Approved for public release: distribuion is unlimited. Licensed by Information Handling Servic

4、esA-A-55635 m 9999974 0367993 8bb D Dash Numbers 1 o1 102 103 1 04 1 05 106 1 07 108 A-A-55615 TABLE 1. DASH NUMBERS AND DIMENSIONS A B Outside Average Ultimate *2 Anchor Wood Screw Size (Lbs.) (Minimum) (Nominal) (Nominal) (Number) Capacity Length Dlameter 6-8 192 1 soo .250 6-8 122 1 .o00 .250 6-8

5、 88 .750 .250 10-1 4 .3125 .750 192 10-14 940 1.500 .375 16-18 41 2 1 .o00 .375 16-18 800 1 soo .3125 10-1 4 360 1 .o00 .3125 1. Recommended safe working load is one-fourth of the average ultimate capacity. 2. Test in accordance with ASTM E488. 2.2 Material for self-threading anchors shall be lead o

6、r lead alloy. 3. QUALITY ASSURANCE PROVISIONS, 3.1 The suppliers shall be responsible for those in process controls and inspections necessary to supply a product consistently conforming to the requirements of this document. 3.2 Upon request, the supplier will certify with documented test/inspection

7、evidence that the part supplied meets the requirements of this document. 4. NOTES. 4.1 Unless otherwise specified, all dimensions are in inches. 4.2 Packaging shall be in accordance with ASTM D 3951. 4.3 Wood screws and lag bolts are not included with self-threading anchors unless 4.4 The part ident

8、ification number (PIN) shall consist of the basic CIO number followed specified in the purchasing contract. by a dash number taken from Table I. Example: AA5561 5-1 O1 Dash number CID Number MILITARY INTERESTS: Custodians: Army - AR Navy - YD Air Force - 99 PREPARING ACTIVITY DLA-IS (Project 5340-2228) 2 Licensed by Information Handling Services