DLA A-A-55614-1995 SHIELD EXPANSION (NON-DRILLING EXPANSION ANCHORS)《扩展护罩(非钻井扩大式壁锚)》.pdf

《DLA A-A-55614-1995 SHIELD EXPANSION (NON-DRILLING EXPANSION ANCHORS)《扩展护罩(非钻井扩大式壁锚)》.pdf》由会员分享，可在线阅读，更多相关《DLA A-A-55614-1995 SHIELD EXPANSION (NON-DRILLING EXPANSION ANCHORS)《扩展护罩(非钻井扩大式壁锚)》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、IINCH-POUNDI A-A-5561 4 19 JULY 1995 COMMERCIAL ITEM DESCRIPTION (NON-DRILLING EXPANSION ANCHORS) SHIELD, EXPANSION The General Services Administrations has authorized the use of this commercial item description for all federal agencies. 1. m. expansion anchors for use in attaching equipment and fix

2、tures to masonry: This Commercial Item Description (CID) covers the following types of non-drilling Type 1 -Expansion anchors, internally threaded, with external slits and single cone expander Type 2-Expansion anchors, externally threaded, with exfernol slits and single cone expander 2. SALIENT CHAR

3、ACTERISTICS. 2.1 Bolt Anchor Configurations. I“Al I I C I OA -C B L Beneficial comments, recommendations, additions, deletions, clarifications, etc., and data which may improve this document should be sent to: Defense industrial Supply Center, ATTN: DISC-ECB, 700 Robbins Avenue, Philadelphia, PA 191

4、 1 1-5096. FSC 5340 ASMC N/A 1 of 2 DISTRIBUTION STATEMENT A. Approved for public release; distribuion is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Num bers 250-20 .375-16 SOO-1 3 .625-11 .750-1 O 101 1 o2 103 104 105 .4375 1.125 -37

5、5 1600 -5625 1.4375 .4375 2500 .6875 1.9375 -6875 3700 .844 2.375 -875 51 O0 1 .o00 3.000 1.125 7100 A-A-5561 4 A Type 2 Outside Dash Thread Size Diameter (Nominal) TABLE I. TYPE 1. DASH NUMBERS AND DIMENSIONS I C B Thread Average Ultimate (Nominal) (Minimum) (Minimum) (Lbs.)(Minimum) Height Length

6、Imbedment Capacity 192 uiiimaTe I I rzr,r.r-,.“ 12 I I Diameter I Height I Threac . (Nominal) (Nominal) (tdnmii 20 1 202 203 204 205 1 .o00 1.250 .250-20 .250 1.750 .625 .375-16 .375 2.250 .625 .500-13 .500 2.750 .875 1 soo .625-11 .625 3.375 1 .o00 2.000 4500 .750-1 O .750 4.250 1.375 2.500 1. Reco

7、mmended safe working load is one-fourth of the average ultimate capacity. 2. Test in accordance with ASTM E488. 2.2 Material for expansion elements and cone expanders shall be carbon or alloy steel. 3. QUALITY ASSURANCE PROVISIONS. 3.1 The suppliers shall be responsible for those in process controls

8、 and inspections necessary to supply 3.2 a product consistently conforming to the requirements of this document. Upon request, the supplier will ceriify with documented test/inspection evidence that the part supplied meets the requirements of this document. 4. NOTES, 4.1 Unless otherwise specified,

9、all dimensions are in inches. 4.2 Bolts are not included with Type 1 non-drilling expansion anchors unless specified in the purchasing contract. 4.3 Nuts and washers are not included with Type 2 non-drilling expansion anchors unless specified in the 4.4 Packaging shall be in accordance with ASTM D 3

10、951. 4.4 purchasing contract. The part identification number (PIN) shall consist of the basic cornmercial item description number followed by a dash number from Table I or Table II. Example: AA5561 4-101 Dash number Basic number MILITARY INTERESTS: Custodians: Army - AR Navy - YO Air Force - 99 Preparing Activity: DIA - IS (Project 5340-2229) 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-