DLA A-A-55602 B-2007 BEARINGS ROLLER CYLINDRICAL SINGLE ROW OF ROLLERS TWO ROLLER RETAINING RIBS ON INNER RING CYLINDRICAL OUTER RING NON-LOCATING《单列圆柱棍子轴承 内圈上有两个固定挡边 圆柱外圈 不定位轴承》.pdf

《DLA A-A-55602 B-2007 BEARINGS ROLLER CYLINDRICAL SINGLE ROW OF ROLLERS TWO ROLLER RETAINING RIBS ON INNER RING CYLINDRICAL OUTER RING NON-LOCATING《单列圆柱棍子轴承 内圈上有两个固定挡边 圆柱外圈 不定位轴承》.pdf》由会员分享，可在线阅读，更多相关《DLA A-A-55602 B-2007 BEARINGS ROLLER CYLINDRICAL SINGLE ROW OF ROLLERS TWO ROLLER RETAINING RIBS ON INNER RING CYLINDRICAL OUTER RING NON-LOCATING《单列圆柱棍子轴承 内圈上有两个固定挡边 圆柱外圈 不定位轴承》.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、 Beneficial comments, recommendations, additions, deletions, clarifications, etc. and any data that may improve this document should be sent to: STDZNMGTdla.mil or Defense Supply Center Richmond (DSCR), ATTN: DSCR-VEB, 8000 Jefferson Davis Highway, Richmond, VA 23297-5616. AMSC N/A FSC 3110 INCH-POU

2、ND A-A-55602B 20 September 2007 SUPERSEDING A-A-55602A 25 January 1996 COMMERCIAL ITEM DESCRIPTION BEARINGS, ROLLER, CYLINDRICAL, SINGLE ROW OF ROLLERS, TWO ROLLER RETAINING RIBS ON INNER RING, CYLINDRICAL OUTER RING, NON-LOCATING The General Services Administration has authorized the use of this co

3、mmercial item description for all federal agencies. 1. SCOPE. This commercial item description (CID) covers the requirements for cylindrical roller bearings, single row of rollers, two roller retaining ribs on inner ring, cylindrical outer ring, non-locating. 2. CLASSIFICATION. The cylindrical rolle

4、r bearings shall be classified by the sizes, cage materials, and precision tolerances listed below: Size - bearing dimensions (see table I and figure 1) Cage materials (see table II) Precision tolerances (see table III) 3. SALIENT CHARACTERISTICS 3.1 Dimensions. The bearings shall be of the dimensio

5、ns corresponding to the dash number in table I and the bore, outside diameter, overall width, and shaft housing and fillet radius corresponding to figure 1 (see 7.3(b). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55602B 2 TABLE I. Dimensional

6、 requirements. Recommended shoulder diameter R Shaft steel cage; greater than normal radial internal clearance; with snap ring. 7.2 Sources of documents. 7.2.1 ABMA standards. Copies of ABMA standards may be obtained from the American Bearing Manufacturers Association, 2025 M Street NW, Suite 800, W

7、ashington, DC 20036. Electronic copies of ABMA standards may be obtained from http:/www.abma-dc.org/. 7.2.2 ASTM standards. Copies of ASTM standards may be obtained from ASTM International, 100 Barr Harbor Drive, P.O. Box C700, West Conshohocken, PA 19428-2959. Electronic copies of ASTM standards ma

8、y be obtained from http:/www.astm.org/. 7.2.3 SAE standards. Copies of SAE standards may be obtained from SAE International, 400 Commonwealth Drive, Warrendale, PA 15096-0001. Electronic copies of SAE standards may be obtained from http:/www.sae.org/. AA55602 - 10 J C3 R Example of reference part nu

9、mber: Cage material: see table II Dash number: see table I CID number Radial internal clearance: see table IIISnap ring: “R“ (if required) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55602B 6 7.3 Ordering data. The acquisition order should sp

10、ecify the following: a. CID document number, revision, and CID PIN. b. Bearing size (see 3.1). c. Cage material type (see 3.2). d. Precision tolerance requirement (see 3.3). e. Preservation, packing, and marking requirements (see 6.1). 7.4 Subject term (key word) listing. brass cage chromium-alloy s

11、teel RBEC-1 MILITARY INTERESTS: CIVIL AGENCY COORDINATING ACTIVITY: Custodians: Army - AT Navy - OS Air Force - 11 GSA - FSS Review Activities: Navy - MC, SH Preparing Activity: DLA - GS4 (Project 3110-2007-004) NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-