DLA A-A-55301-1996 WEBBING TEXTILE TEXTURED OR MULTIFILAMENT NYLON《纹理或尼龙纺织带状织物》.pdf

《DLA A-A-55301-1996 WEBBING TEXTILE TEXTURED OR MULTIFILAMENT NYLON《纹理或尼龙纺织带状织物》.pdf》由会员分享，可在线阅读，更多相关《DLA A-A-55301-1996 WEBBING TEXTILE TEXTURED OR MULTIFILAMENT NYLON《纹理或尼龙纺织带状织物》.pdf（15页珍藏版）》请在麦多课文档分享上搜索。

1、W 9038054 0003954 974 D INCH-POUND A-A-55301 November 15,1996 COMMERCIAL ITEM DESCRIPTION WEBBING, TEXTILE, TEXTURED OR MULTIFILAMENT NYLON The General Services Administration has authorized the use of this commercial item description as a replacement for MIL-W-43668 for all Federal agencies. 1 SCOP

2、E. This document covers textured or multifilament nylon (or similar) webbing used for indmequipment belts, rifle slings and load carrying equipment 2. CLASSIFICATION. The webbing shall be in the following types: Type I 2 1/4 inches Type II 1 1/4 inches Type III 1 inch Type IV t 3/4 inch Type V 5/8 i

3、nch Type VI 1 1/2 inch 3. SALIENT CHARACTERISTICS. The webbing shall be made with either textured or untextured synthetic yarn in 6 widths as specified in para 2. 3.1 Materials (descrintion of materias. 3.1.1 Yarn. The yarn for the warp and filling for all types, except for types I and III alternate

4、, shall bxat and light resistant, continuous filament textured nylon yam. Air Jet texturing is acceptable. The filling yarn for type III alteniate shall be textured yarn and the warp yarn for type III alternate shall be textured yarn and the warp yarn for type III alternate and the warp for type I a

5、ltemate shall be heat and light resistant multifilament yam. The yams for ail webbing shall not be subjected to any type of bleaching process. 3.1.2 Twist. When untextured yarn is used the face, back and binder warps of the Type I construction the yarn shall have a minimum of 2 1/2 turns per inch in

6、 the find twist. The number of singles yarn shall be twisted together in one operation. 3.2 Color. The color shall be as specified by the procuring activity. Beneficial comments, recommendations, additions, deletions, clarifications, etc. and any data which may improve this document should be sent t

7、o: Defense Personnel Support Center, Clothing and Textiles Directorate, Attn: DPSC-FNS, 2800 South 20th Street, Philadelphia, PA 19145-5099. AMSC N/A FSC 8305 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited Provided by IHSNot for ResaleNo reproduction or networking p

8、ermitted without license from IHS-,-,-= 9038054 0003955 800 = Wavelength( nm) 600 620 640 660 A-A-5530 1 Reflectance) Min Mm 3 10 3 10 3 10 3 11 3.2.1 Matchin . The color of the dyed webbing shall match the standard sample (Samples can be obhdm DPSC) when viewed under filtered tungsten lamp which ap

9、proximate artificial daylight having a correlated color temperature of 7500+/- 200K, with illumination of 100 +I- 20 foot candles, and shall be a good match to the standard sample under incandescent lamplight at 2300 +/- 200 K. Wavelength(nm) 740 760 780 800 820 840 860 3.2.2 Colorfastness. The dyed

10、 webbing shall show fastness to light and laundering equal to or better than the standard sample or equal to or better than a rating of 4 when tested against it self. The number of test samples shall be one per sample unit and the size shall be two to six grams of webbing(test methods AATCC 61-1A-19

11、89 and AATCC 16 Opt A-1990). The dyed webbing shall show fastness to crocking equal to or better than the standard sample or shall have an AATCC Chromatic Transference scale rating of not lower than 3.5 (Test method AATCC 8- 1989). Reflectance(%) Min Mm 7 52 11 60 17 64 24 67 32 70 37 71 40 73 3.2.3

12、 Spectral reflectance for Camouflage green 483. Finished Camouflage Green 483 webbing greater than 1 1/4 inches in width shall meet the spectral reflectance factors (in percent) for the visiblehear infrared wavelength range 600 to 860 nanometers (nm) as specified below when tested as follows. Spectr

13、al reflectance data shall be obtained fkom 600 to 860 nanometers (nm), at 20 nm intervals on the spectrophotomer relative to a barium sulfate standard, the prefered white reference standard. Other white reference materials may be used, provided they are calibrated to absolute white; e.g, Halon, magn

14、esium oxide, or vitrolite tiles. The spectral bandwidth shall be less than 26 nm at 860 nm. Reflectance measurements may be made by either the monochromatic or polychromatic mode of operation. . Whenthe polychromatic mode is used, the spectrophotometer shall operate with the specimen diffusely illum

15、inated with the full emission of the source that simulates either CIE Source A or CIE Source D65. The specimen shall be measured as a single layer, backed with two layers of the same webbing and shade. Measurements will be taken on a minimum of two different areas and the data averaged. The specimen

16、 shall be viewed at an angle no greater than 1 O from normal, with the specular component included. Photometric accuracy of the spectrophotometer shall be within one percent and wavelength accuracy within 2 nm. The standard aperture size used in the color measurement device shall be 1 .O to 1.25 inc

17、hes in diameter. When the measured reflectance values for any color at four or more wavelengths do not meet the limits specified in the chart below, it shall be a test failure. Spectral Reflectance Requirements for Camouflage Green 483 680 I 3 13 700 I 4 I 28 720 I 5 I 40 3.3 Physical requirements.

18、The dyed webbing shall conform to the requirements in table I. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-9018054 O001956 747 3.85 0.70 - 2.30 A-A-55301 1.10 0.5 0.48 0.32 I_ _- - _- TABLE I. Physical requirements Warp ends, full width: Face,

19、back, and middle warps.(min) Face and back (min) Binder warp (min) Stuffer warp (min) Pickdinch (min) Pickdinch (min) (shuttleless loom) Breaking strength lbs (min) - 5/ - IWidth, inches I 2000 1 O00 875 625 b1/4-1/16 21/8 I 1/4+1/16r 1+1/16 -1 3/4 +1/16 I 5/8+1/16 Characteristics Width, inches Thic

20、kness inches 21 Weight oz./lin.yd (Min) 3/ Stiffness load pounds widthwise only 4/ Warp ends, full width: Face and back (min) Binder warp (min) Stuffer warp (min) Pickshch (min) Picksinch (min) (shuttleless loom) Breaking strength Ibs (min) 51 Face, back, and Middle warps (min) /Thickness inches 2/

21、I 0.125 - 0.150 10.075 + 0.007 I 0.046 + 0.007 I 0.055 - 0.0700 I 0.038 - 0.050 Type I (Alternate) Type III (Alternate) Type VI 2 1/4 - 1/16 12 1/16 1 1/2+ - 1/16 0.125 - 0.150 0.046 + 0.007 0.046+ - 0.007 3.85 0.65 1.10 - - 0.70 - 2.30 - _- - 83 97 137 38 22 30 304 _ - 58 1/ 80 1/ 80 11 - 1 O00 150

22、0 Weight oz./lin.yd (Min) 31 Stiffness load pounds widthwise t- only 4/ 33 I 36 64 1/ I 46 I/ I 72 1/ I 66 1/ I 72 1/ TABLE I. Physical requirements(cont) 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-9018054 0001957 683 A-A-55301 4/ Test method

23、FED STD 191 method 5202 2 by 1 inch specimen, long dimension in filling 5/ Test method FED STD 19 1 method 41 08 direction. The specimen shall be bent to a 20 degree angular deflection. 3.4 Weaves. 3.4.1 Type I. The webbing shall be three layers, bound by a binder which weaves 3 up (face, middle, fa

24、ce) 3 down (back, middle, back) to form a filling rib effect on both face and back. The middle layer shall weave 2 ends as 1 equivalent. See Figure 1. 3.4.2 Type I Alternate. The Weave shall be as specified in figure 5. 3.4.3 Type II. The webbing shall be a tubular plain weave bound together by a pl

25、ain weave binder. See Fig 6. 3.4.4 Type III. The webbing shall be a tubular weave bound together by a plain weave binder. See Fig. 7. 3.4.5 T e III Alternate. The webbing shall be a tublar plain weave, weaving 2 ends as 1 or equiva ?%77- ent oun together by a binder weaving 2 up and 2 down, the adja

26、cent finder weaving 2 down and 2 up. See Fig. 8. 3.4.6 Type IV. The webbing shall be a tubular plain weave with stuffer bound by a plain weave binder. See Fig. 9. 3.4.7 Type V. The webbing shall be a tubular plain weave bound by a plain weave binder. See Fig. 7. 3.4.8 Type VI. Same as Type III Alter

27、nate. See Paragraph 3.4.5. NOTE: When shuttleless loom construction is used, a catchcord will be incorporated in all types depicted in figures 2 or 3. 3.5 pH. The pH value of the water extract of dyed webbing shall be no less than 5.0 nor more than 8.5 when tested under FED STD 191 method 28 1 1. 3.

28、5 1. Curvature. The finished webbing shall show no more lateral curvature than 1/4 inch withiximshown in figure 4. The test specimen shall be a length of webbing, full width, measuring a minimum of 40 inches. The specimen shall bot be stretched smoothed, or otherwise changed fiom its original condit

29、ion prior to testing. Five specimens shall be tested fiom each sample unit. 3.6 LabeVta . Each roll or spool shall be individually bar-coded. The bar coding element shall density and shall be located so that it is completely visible on the item when it is folded andor packaged as specified and so th

30、at it causes no damage to the item. be a 75 13 igit national stock number (NSN). The bar code type shall be a medium to high code 4. REGULATORY REQUIREMENTS. The offeror/contractor is encouraged to use recovered materials to the maximum extent practicable, in accordance with paragraph 23.403 of the

31、Federal Acquisition Regulation (FAR). 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-? 90313054 0003958 5LT A-A-55301 5. OUALITY ASSURANCE PROVISIONS 5.1 Product Conformance. The products provided shall meet the salient characteristics of this com

32、mercial item description, conform to the producers own drawings, specifications, standards, and quality assurance practices, and be the same product offered for sale in the commercial market. The government reserves the right to require proof of such conformance. 5.2 Market acceptance criteria. The

33、item offered, or a generic equivalent, must have been sold to the commercial market or to the Government for at least two years. 5.3 Warran . The item offered shall include the standard warranty given to the commercial market + eginning with the date of delivery of the individual items. 5.4 Visual e

34、xamination. Each yard shall be examined for the defects listed below. 5.4.1 Defects. Any hole, cut, or tear; broken or missing yarn; smash; float, mispick, harness skip, ormisweave; hitchback, stripback open or thin place, crack (warp or filling); knot or slub; loose, slack, or tight yarns; reed mar

35、k, wrong draw; abrasion mark, bruise, tender or weak spot; embedded crease or wrinkle; selvage cut, torn, folded, rolled, slack, or tight; filling bar, coarse filling, or mixed filling; spot, stain, streak, or dirty yarn; foreign matter; shade not as specified; finish not equal to or better than sta

36、ndard; offshade or uneven shading throughout piece; mottled, cloudy, streaky, or barre; overall uncleanness or soiled; baggy, ridgy, wavy, or unevenly woven; width not within established tolerances; net length less than indicated on the ticket; fiber identification marking omitted; bar code omitted

37、or not readable by scanner; human- readable interpretation (HRI) omitted or illegible; bar code not visible on roll; bar code causes damage to the item; any items not packaged in accordance with the contract or purchase order. Each defect shall be marked with a 1-112 inch long string; the string sha

38、ll be inserted into the selvage opposite the defect, 5.4.2 Acceptance Criteria. Acceptance Criteria shall be as specified in the contract or purchase order. 6. PACKAGING 6.1 Preservation, packing, and marking. The preservation, packing, and marking shall be as specified in the contract or order. 7.

39、NOTES 7.1 Source of Government documents. Copies of military and Federal documents are available from: Standardization Documents Order Desk Bldg. 4D 700 Robbins Avenue Philadelphia, PA 191 1 1-5094 7.2 Source of non-Govemment documents ASTM Test Methods 5 Provided by IHSNot for ResaleNo reproduction

40、 or networking permitted without license from IHS-,-,-W 9018054 0001959 456 D A-A-55301 (Applications for copies should be addressed to American Society For Testing and Materiais, 100 Barr Harbor Drive, West Conshohocken,PA 19428-2959.) AATCC Test Method (Applications for copies should be addressed

41、to American Association of Textile Chemists and Colorists (AATCC), P.O. Box 122 15, Triangle Park, NC 27709-221 5.) MILITARY INTERESTS: Custodians Navy - AS Air force - 99 Army - GL Review Activities AITIly-MD Navy - NU Air Force - 11 CIVIL AGENCY COORDINATING ACTIVITY: GSA - FSS PREPARING ACTIVITY:

42、 DLA - CT Project 83 05 -06 1 7 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-= 7018054 OOOL760 178 A-A-5530 1 FACE AND BACK WARP YARNS WEAVING ONE END AS ONE MIDDLE WARP YARNS WEAVING TWO ENDS AS ONE BINDER WARP YARNS WEAVING TWO ENDS AS ONE FIG

43、URE I. CROSS SECTION FILLING 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-OLBO54 000LbL 004 = A-A-55301 Selvage locked by knitting filling loops szmultancously with additional catch thread using “inclined“ latch needle. FIGURE 2. CATCH CORD DIAG

44、RAM Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- W 7038054 OOOLb2 T40 m A-A-55301 FIGURE 3. CATCH CORD DIAGRAM 9 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- _ _ I 9038054 O003963 987 A-A-5530

45、1 FIGURE 4. DIAGRAM CURVATURE MEASUREMENT 10 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-? 9038054 0001bY 833 A-A-5530 1 EDGE BODY ONE REPEAm WEAVE DIAGRAM EDGE FACE WARP - WEAYE 1 END AS 1 STUFFER WARP- WEAW 4 ENDS AS 1 BINDER WARP-NEAYE 2 ENDS

46、AS 1 FIGURE 5 11 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- W 9038054 0003965 75T A-A-55301 tgg “ -3 EDGE BODY EGE ONE REPEAT TYPEII - 1-1/4INCHES FIGURE 6. WEAVE DIAGRAM 12 Provided by IHSNot for ResaleNo reproduction or networking permitted w

47、ithout license from IHS-,-,-m 9018054 0001bb bb m A-A-5530 1 EDGE TYPE 111 - 1 INCH TYPE V- 5/8 INCH EDGE FIGURE 7. WEAVE DIAGRAM Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-9038054 00039b7 522 A-A-55301 EDGE FACE WARP - WEAVE 1 END A!S 1 BINDERW

48、ARF - WEAVE 7 END AS 7 TYPE 111 - ALTERNATE - I INCH TYPE VI - 1-112 INCHES FIGURE 8. WEAVE DIAGRAM 14 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- 9038054 0003968 Lib9 A-A-55301 FACE WARP - 1 END AS 1 STUFFER WARP- 3 ENI) AS 1 BJNDER WARP - 1 END AS 1 1 TYPE IV - 314 INCH FIGURE 9. WEAVE DIAGRAM 15 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-