DLA A-A-55088 C-2010 RESISTORS FLAMEPROOF FUSIBLE.pdf

《DLA A-A-55088 C-2010 RESISTORS FLAMEPROOF FUSIBLE.pdf》由会员分享，可在线阅读，更多相关《DLA A-A-55088 C-2010 RESISTORS FLAMEPROOF FUSIBLE.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、AMSC N/A FSC 5905 INCH-POUND A-A-55088C 9 June 2010 SUPERSEDING A-A-55088B 9 September 2003 COMMERCIAL ITEM DESCRIPTION RESISTORS, FLAMEPROOF, FUSIBLE The General Services Administration has authorized the use of this Commercial Item Description (CID) for all federal agencies. 1. SCOPE. This (CID) c

2、overs the general requirements for flameproof, fusible resistors. These resistors act as a wire-wound resistor and a fuse, and are used in applications where precise control of fusing point and time lags are necessary. These resistors eliminate fire hazard and circuit board damage due to overheated

3、components. Resistors covered by this CID are intended for commercial/industrial applications and are not used in military systems needing stringent environmental and electrical requirements. * 2. CLASSIFICATION or IDENTIFICATION NUMBER (PIN). This CID uses a classification system which is included

4、in the PIN as shown in the following examples (see 7.1). AA55088 - 01 K CID number Dash number (see table I) Resistance tolerance (see 3.3) 3. SALIENT CHARACTERISTICS. 3.1 Interface and physical dimensions. The resistors supplied to this CID shall meet the interface and physical dimensions as specif

5、ied herein (see figure 1). 3.2 Resistance value. The resistance range shall be 0.2 ohm minimum to 200 ohms maximum. Specific resistance values are specified in table I by dash number. 3.3 Resistance tolerance. Resistors are available in resistance tolerances (K) 10 percent, (J) 5 percent, and (G) 2

6、percent. 3.4 Operating temperature. The operating temperature range shall be -55C to +150C. 3.5 Temperature coefficient. The temperature coefficient shall be 150 ppm for less than 1 ohm, and 50 ppm for 1 ohm and above. Beneficial comments, recommendations, additions, deletions, etc. and any data tha

7、t may improve this document should be sent to: Defense Supply Center Columbus, ATTN: DSCC-VAT, Post Office Box 3990, Columbus, OH 43218-3990, or emailed to resistordla.mil. Since contact information can change, you may want to verify the currency of this address information using the ASSIST Online d

8、atabase at https:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55088C 2 3.6 Fusing characteristics. The fusing characteristics shall be in accordance with table I. * NOTES: 1. Dimensions are in inches. 2. Metric equivalent

9、s are given for general information only. FIGURE 1. Configuration and dimensions. 3.7 Marking. Resistors supplied to this commercial item description shall be marked with the manufacturers standard commercial PIN. * 3.8 Recycled, recovered, or environmentally preferable materials. Recycled, recovere

10、d, or environmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs. * 3.9 Workmanship. Resistors shall be processed in such a manner

11、 as to be uniform in quality and shall be free from other defects that will affect life, serviceability, or appearance. 4. REGULATORY REQUIREMENTS. The offeror/contractor is encouraged to use recovered materials to the maximum extent practicable, in accordance with 23.403 of the Federal Acquisition

12、Regulation (FAR). 5. PRODUCT CONFORMANCE PROVISIONS. 5.1 Product conformance. The products provided shall meet the salient characteristics of this CID, conform to the producers own drawings, specifications, standards, and quality assurance practices, and is the same product offered for sale in the c

13、ommercial market. The Government reserves the right to require proof of such conformance. 6. PACKAGING. Preservation, packing, and marking shall be as specified in the contract or order. Ltr Inches mm Min Max Min Max A 1.25 - 31.75 - B - .400 - 10.16 C .020 0.51 D - .155 - 3.94 Provided by IHSNot fo

14、r ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55088C 3 TABLE I. Fusing characteristics. Dash number Resistance (ohms) Steady state Blow condition I Blow condition II Current Dissipation (watts) Current Dissipation (watts) Blow time (T max) Current Dissipation (watt

15、s) Blow time (T max) -01 0.2 2.2 A 1.0 10 A 20 500 ms 25 A 125 50 ms -02 0.2 2.2 A 1.0 10 A 20 300 ms 25 A 125 30 ms -03 0.5 1.4 A 1.0 6 A 18 10 sec 15 A 112 100 ms -04 0.5 1.4 A 1.0 6 A 18 500 ms 15 A 112 50 ms -05 0.5 1.4 A 1.0 6 A 18 50 ms 15 A 112 10 ms -06 1.0 1.0 A 1.0 4 A 16 10 sec 10 A 100 1

16、00 ms -07 1.0 1.0 A 1.0 4 A 16 500 ms 10 A 100 50 ms -08 1.0 1.0 A 1.0 4 A 16 50 ms 10 A 100 10 ms -09 2.0 700 mA 1.0 3 A 18 10 sec 7 A 98 50 ms -10 2.0 700 mA 1.0 3 A 18 200 ms 7 A 98 50 ms -11 2.0 700 mA 1.0 3 A 18 50 ms 7 A 98 10 ms -12 5.0 450 mA 1.0 2 A 20 200 ms 4.5 A 101 50 ms -13 5.0 400 mA

17、0.8 1.5 A 10 50 ms 4.0 A 80 10 ms -14 5.0 350 mA 0.6 1.0 A 5 100 ms 1.4 A 10 20 ms -15 10 300 mA 0.9 1.2 A 14 200 ms 3.0 A 90 10 ms -16 10 300 mA 0.9 1.0 A 10 100 ms 1.3 A 17 50 ms -17 10 200 mA 0.4 600 mA 3.6 100 ms 900 mA 8 50 ms -18 20 220 mA 1.0 600 mA 7.2 10 sec 900 mA 16 100 ms -19 20 220 mA 1

18、.0 600 mA 7.2 100 ms 900 mA 16 50 ms -20 20 150 mA 0.4 350 mA 2.4 500 ms 450 mA 4 50 ms -21 50 140 mA 1.0 400 mA 8.0 500 ms 600 mA 18 50 ms -22 50 130 mA 0.8 350 mA 6.1 100 ms 450 mA 10 50 ms -23 50 80 mA 0.3 200 mA 2.0 200 ms 240 mA 2.9 50 ms -24 100 100 mA 1.0 250 mA 6.2 10 sec 300 mA 9.0 100 ms -

19、25 100 80 mA 0.6 200 mA 4.0 200 ms 250 mA 6.2 250 ms -26 100 60 mA 0.4 140 mA 2.6 10 sec 180 mA 3.2 200 ms -27 200 70 mA 1.0 200 mA 8.0 10 sec 250 mA 12.5 100 ms -28 200 60 mA 0.8 150 mA 4.0 100 ms 250 mA 12.5 10 ms 7. NOTES 7.1 PIN. The PIN should be used for Government purposes to buy commercial p

20、roducts to this CID. See section 2 for PIN format example. * 7.2 Environmentally preferable material. Environmentally preferable materials should be used to the maximum extent possible to meet the requirements of this specification. As of the dating of this document, the U.S. Environmental Protectio

21、n Agency (EPA) is focusing efforts on reducing 31 priority chemicals. The list of chemicals and additional information is available on their website at http:/www.epa.gov/osw/hazard/wastemin/priority.htm. Included in the EPA list of 31 priority chemicals are cadmium, lead, and mercury. Use of these m

22、aterials should be minimized or eliminated unless needed to meet the requirements specified herein (see Section 3).” 7.3 Commercial and Government Entity (CAGE) code. For ordering purposes, inventory control, and submission of these resistors to DSCC under the Military Parts Control Advisory Group (

23、MPCAG) evaluation program, CAGE code 58536 should be used. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55088C 4 * 7.4 Source of documents. FEDERAL REGULATIONS FAR 23.403 - Federal Acquisition Regulations (FAR) Use of Recovered Materials. (Cop

24、ies of these documents are available online at www.acquisition.gov/comp/far/index.html or from the U. S. Government Printing Office, 732 North Capital Street, NW Washington D.C. 20401.) 7.5 Ordering data. The contract or order should specify the following: a. CID document number, revision, and CID P

25、IN. b. Product conformance provisions. c. Packaging requirements. * 7.6 Commercial products. As part of the market analysis and research effort, this CID was coordinated with the following manufacturers of commercial products. At the time of CID preparation and coordination, these manufacturers were

26、 known to have commercial products that would meet the requirements of this CID. (NOTE: This information should not be considered as a list of approved manufacturers or be used to restrict procurement to only the manufacturers shown). MFRs CAGE MFRs name and address 54294 IRC, Incorporated Wirewound

27、 and Film Technologies Division 736 Greenway Road Boone, North Carolina 28607-1860 Phone:828-264-8861 Fax:828-264-8866 Email: Website: 56637 RCD Components, Incorporated 520 East Industrial Park Drive Manchester, NH 03109-5316 Phone: (603) 669-0054 Fax: (603) 669-5455 Email: Website: 7.7 Part nu

28、mber (P/N) supersession data. This CID supersedes the following manufacturers P/N as shown in table II. This information is being provided to assist in reducing proliferation in the Government inventory system. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from

29、 IHS-,-,-A-A-55088C 5 TABLE II. P/N supersession data. CID dash number (see table I) MFRs CAGE MFRs P/N 1/ CID dash number (see table I) MFRs CAGE MFRs P/N 1/ AA55088-01* AA55088-02* AA55088-03* AA55088-04* AA55088-05* AA55088-06* AA55088-07* AA55088-08* AA55088-09* AA55088-10* AA55088-11* AA55088-1

30、2* AA55088-13* AA55088-14* 54294 F501 F502 F503 F504 F505 F506 F507 F508 F509 F510 F511 F512 F513 F514 AA55088-15* AA55088-16* AA55088-17* AA55088-18* AA55088-19* AA55088-20* AA55088-21* AA55088-22* AA55088-23* AA55088-24* AA55088-25* AA55088-26* AA55088-27* AA55088-28* 54294 F515 F516 F517 F518 F51

31、9 F520 F521 F522 F523 F524 F525 F526 F527 F528 AA55088-01* AA55088-02* AA55088-03* AA55088-04* AA55088-05* AA55088-06* AA55088-07* AA55088-08* AA55088-09* AA55088-10* AA55088-11* AA55088-12* AA55088-13* AA55088-14* 56637 FR88-01 FR88-02 FR88-03 FR88-04 FR88-05 FR88-06 FR88-07 FR88-08 FR88-09 FR88-10

32、 FR88-11 FR88-12 FR88-13 FR88-14 AA55088-15* AA55088-16* AA55088-17* AA55088-18* AA55088-19* AA55088-20* AA55088-21* AA55088-22* AA55088-23* AA55088-24* AA55088-25* AA55088-26* AA55088-27* AA55088-28* 56637 FR88-15 FR88-16 FR88-17 FR88-18 FR88-19 FR88-20 FR88-21 FR88-22 FR88-23 FR88-24 FR88-25 FR88-

33、26 FR88-27 FR88-28 1/ The manufacturers P/N shall not be used for procurement to the requirements of this CID. At the time or preparation of this CID, the aforementioned commercial products were reviewed and could be replaced by the CID PIN shown. 7.8 Government users. To acquire information on obta

34、ining these resistors from the Government inventory system, Defense Supply Center, Columbus, ATTN: DSCC-CPB, Post Office Box 3990, Columbus, OH 43218-3990, or telephone (614) 692-7678. * 7.8.1 National stock number. This section is not applicable to this CID. Provided by IHSNot for ResaleNo reproduc

35、tion or networking permitted without license from IHS-,-,-A-A-55088C 6 * 7.9 Changes from previous issue. The margins of this CID specification sheet are marked with an asterisk to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assume

36、s no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. MILITARY INTERESTS: CIVIL AGENCY COOR

37、DINATING ACTIVITY: Custodian: GSA - 7FXE NAVY - EC DLA - CC Preparing activity: DLA - CC Project 5905-2010-013 NOTE: The activities listed above were interested in this document as the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-