DIN EN 932-5-2012 Tests for general properties of aggregates - Part 5 Common equipment and calibration German version EN 932-5 2012《集料的一般性能试验 第5部分 通用设备和校正》.pdf

《DIN EN 932-5-2012 Tests for general properties of aggregates - Part 5 Common equipment and calibration German version EN 932-5 2012《集料的一般性能试验 第5部分 通用设备和校正》.pdf》由会员分享，可在线阅读，更多相关《DIN EN 932-5-2012 Tests for general properties of aggregates - Part 5 Common equipment and calibration German version EN 932-5 2012《集料的一般性能试验 第5部分 通用设备和校正》.pdf（27页珍藏版）》请在麦多课文档分享上搜索。

1、May 2012 Translation by DIN-Sprachendienst.English price group 12No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 91

2、.100.15!$|+_“1890860www.din.deDDIN EN 932-5Tests for general properties of aggregates Part 5: Common equipment and calibrationEnglish translation of DIN EN 932-5:2012-05Prfverfahren fr allgemeine Eigenschaften von Gesteinskrnungen Teil 5: Allgemeine Prfeinrichtungen und KalibrierungEnglische bersetz

3、ung von DIN EN 932-5:2012-05Essais pour dterminer les proprits gnrales des granulats Partie 5: Equipments communs et talonnageTraduction anglaise de DIN EN 932-5:2012-05SupersedesDIN EN 932-5:2000-01www.beuth.deDocument comprises 27 pagesIn case of doubt, the German-language original shall be consid

4、ered authoritative.04.12 DIN EN 932-5:2012-05 2 A comma is used as the decimal marker. National foreword This standard has been prepared by Technical Committee CEN/TC 154 “Aggregates” (Secretariat: BSI, United Kingdom). The responsible German body involved in its preparation was the Normenausschuss

5、Materialprfung (Materials Testing Standards Committee), Working Committee NA 062-03-13 AA Gemeinschaftsarbeitsausschuss NMP/FGSV: Gesteinskrnungen; Prfverfahren, Petrographie, Probenahme und Przision. The DIN Standards corresponding to the International Standards referred to in this document are as

6、follows: ISO 384 DIN ISO 384 ISO 386 DIN 12770 ISO 3310-1 DIN ISO 3310-1 ISO 3310-2 DIN ISO 3310-2 ISO 4788 DIN EN ISO 4788 Amendments This standard differs from DIN EN 932-5:2000-01 as follows: a) terms and definitions have been added; b) categories of balances have been included; c) measurement in

7、struments have been added; d) calibration and checking intervals have been included; e) Annex C contains now a balance recommendation for various standard test methods and a new Annex B “Procedure for the manual checking of perforated plate test sieve openings” has been included. Previous editions D

8、IN EN 932-5: 2000-01 National Annex NA (informative) Bibliography DIN 12770, Laboratory glassware Liquid-in-glass thermometers General requirements DIN EN ISO 4788, Laboratory glassware Graduated measuring cylinders DIN ISO 384, Laboratory glassware Principes of design and construction of volumetric

9、 glassware DIN ISO 3310-1, Test sieves Technical requirements and testing Part 1: Test sieves of metal wire cloth DIN ISO 3310-2, Test sieves Technical requirements and testing Part 2: Test sieves of perforated plates EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 932-5 February 2012 ICS 91.10

10、0.15 Supersedes EN 932-5:1999English Version Tests for general properties of aggregates - Part 5: Common equipment and calibration Essais pour dterminer les proprits gnrales des granulats - Partie 5: Equipements communs et talonnagePrfverfahren fr allgemeine Eigenschaften von Gesteinskrnungen - Teil

11、 5: Allgemeine Prfeinrichtungen und Kalibrierung This European Standard was approved by CEN on 30 December 2011. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any al

12、teration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language m

13、ade by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Est

14、onia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISA

15、TION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 932-5:2012: EEN 932-5:2012 (E) 2 Contents Page Foreword 31 Scope 42 Normative references

16、43 Terms and definitions .54 Common equipment 54.1 Tolerances 54.1.1 Manufacturing tolerances .54.1.2 Working tolerances64.2 Measuring instruments .64.2.1 General 64.2.2 Balances and weights .64.2.3 Thermometers 74.2.4 Dimensional measurement instruments .74.2.5 Timers .84.2.6 Volumetric glassware 8

17、4.2.7 Density hydrometers .84.3 Other instruments 84.3.1 Ovens 84.3.2 Constant temperature bath .84.3.3 Test sieves and bar sieves .84.3.4 Moulds and drums .84.3.5 Sieve shakers .94.3.6 Desiccators and desiccator cabinets 94.3.7 Bottle shakers and rollers .94.3.8 Heaters 94.3.9 Rotating machinery .9

18、4.3.10 Vibrating machinery 94.3.11 Pressure or vacuum 95 Calibration and checking 95.1 Calibration of reference standards and reference instruments 95.1.1 Laboratory reference standards .95.1.2 Specifications for reference standards and reference instruments 105.2 Calibration and checking of test eq

19、uipment 115.2.1 Traceability 115.2.2 External and in-house calibration . 115.2.3 Calibration and checking of measuring instruments 125.2.4 Checking of other instruments 146 Reagents 176.1 Distilled water 176.2 Chemical reagents 18Annex A (normative) Method for the performance check of sieves . 19Ann

20、ex B (normative) Procedure for the manual checking of perforated plate test sieve openings 22B.1 Equipment for checking the openings of plate test sieves 22B.2 Calibration of sieve check gauges 22B.3 Test procedure 22Annex C (informative) Balance recommendation for various standard test methods 24Bi

21、bliography . 25DIN EN 932-5:2012-05 EN 932-5:2012 (E) 3 Foreword This document (EN 932-5:2012) has been prepared by Technical Committee CEN/TC 154 “Aggregates”, the secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by publication of

22、an identical text or by endorsement, at the latest by August 2012, and conflicting national standards shall be withdrawn at the latest by August 2012. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be

23、 held responsible for identifying any or all such patent rights. This document supersedes EN 932-5:1999. This standard forms part of a series of standards for general properties of aggregates. Test methods for other properties of aggregates are covered by the following European Standards: EN 933, Te

24、sts for geometrical properties of aggregates; EN 1097, Tests for mechanical and physical properties of aggregates; EN 1367, Tests for thermal and weathering properties of aggregates; EN 1744, Tests for chemical properties of aggregates; EN 13179, Tests for filler aggregate used in bituminous mixture

25、s. The other parts of EN 932, Tests for general properties of aggregates are: Part 1: Methods for sampling; Part 2: Methods for reducing laboratory samples; Part 3: Procedure and terminology for simplified petrographic description; Part 6: Definitions of repeatability and reproducibility. In the bib

26、liography, reference is made to the International Organization for Legal Metrology (OIML) classification, which this standard has adopted for the purposes of establishing a frequency of calibration for balance weights. According to the CEN/CENELEC Internal Regulations, the national standards organiz

27、ations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portu

28、gal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. DIN EN 932-5:2012-05 EN 932-5:2012 (E) 4 1 Scope This European Standard specifies general requirements for common equipment, calibration and checking procedures and reagents for the testing of the properties

29、 of aggregates. In the case of checking, other procedures than the ones described in this standard may be used provided that appropriate working relationships with the corresponding methods described in this standard have been established. In case of dispute, the checking methods described in this s

30、tandard shall be used. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced docume

31、nt (including any amendments) applies. EN 933-1, Tests for geometrical properties of aggregates Part 1: Determination of particle size distribution Sieving method EN 933-2, Tests for geometrical properties of aggregates Part 2: Determination of particle size distribution Test sieves, nominal size of

32、 apertures EN 933-3, Tests for geometrical properties of aggregates Part 3: Determination of particle shape Flakiness index EN 933-8, Tests for geometrical properties of aggregates Part 8: Assessment of fines Sand equivalent test EN ISO 3650, Geometrical product specifications (GPS) Length standards

33、 Gauge blocks (ISO 3650:1998) ISO 384, Laboratory glassware Principles of design and construction of volumetric glassware ISO 386, Liquid-in-glass laboratory thermometers Principles of design, construction and use ISO 649-1, Laboratory glassware Density hydrometers for general purposes Part 1: Speci

34、fication ISO 3310-1, Test sieves Technical requirements and testing Part 1: Test sieves of metal wire cloth ISO 3310-2, Test sieves Technical requirements and testing Part 2: Test sieves of perforated metal plate ISO 4788, Laboratory glassware Graduated measuring cylinders ISO 6353-2, Reagents for c

35、hemical analysis Part 2: Specifications - First series ISO 6353-3, Reagents for chemical analysis Part 3: Specifications Second series DIN EN 932-5:2012-05 EN 932-5:2012 (E) 5 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 calibration operat

36、ion that, under specified conditions, in a first step, establishes a relation between the quantity values with measurement uncertainties provided by measurement standards and corresponding indications with associated measurement uncertainties and, in a second step, uses this information to establish

37、 a relation for obtaining a measurement result from an indication. Note 1 to entry: A calibration may be expressed by a statement, calibration function, calibration diagram, calibration curve, or calibration table. In some cases, it may consist of an additive or multiplicative correction of the indi

38、cation with associated measurement uncertainty. Note 2 to entry: For more information, see VIM International vocabulary of basic and general terms in metrology (available on http:/www.bipm.org/ ). 3.2 checking operation of assuring either: that the results of measurements of a property (such as leng

39、th, mass, temperature or time) at selected values made by a measuring instrument, or a set of them, have not deviated from that which was measured when the equipment was last calibrated within a pre-defined tolerance; or that a property (such as rotation speed, vibration frequency) of an item, or a

40、set of items, of equipment complies with the relevant requirements for that equipment. 3.3 verification scale interval (e) for balances value, expressed in units of mass, used for the classification and verification of a balance 3.4 actual scale interval (d) value, expressed as: the difference betwe

41、en the values corresponding to two consecutive scale marks, for analogue indication, or the difference between two consecutive indicated values, for digital indication. 3.5 tolerance maximum permissible deviation from the nominal value of a measurable characteristic Note 1 to entry: In the present s

42、tandard, tolerances may be expressed either as an absolute quantity without sign or as a percentage of the nominal value of a measurable characteristic. 4 Common equipment 4.1 Tolerances 4.1.1 Manufacturing tolerances NOTE By convention, the tolerances (or limits) indicated in the aggregate test sta

43、ndards are manufacturing tolerances (or limits), if not otherwise stated. DIN EN 932-5:2012-05 EN 932-5:2012 (E) 6 4.1.1.1 Linear dimensions Where a dimension is specified with manufacturing tolerances or limits, it shall be an essential dimension. NOTE Dimensions stated without tolerances are given

44、 for guidance. 4.1.1.2 Mass Where mass is specified, the manufacturing tolerance shall be 1 % of the specified mass unless otherwise stated. 4.1.2 Working tolerances Working tolerances apply to equipment (e.g. apparatus) after being subjected to wear in use, and shall be not more than twice the manu

45、facturing tolerance unless otherwise specified. 4.2 Measuring instruments 4.2.1 General Measuring instruments shall have greater measurement accuracy than the corresponding tolerance defined in the test method. NOTE Unless stated otherwise, the measurement accuracy of the instrument used should be a

46、t least five times better than the corresponding tolerance. 4.2.2 Balances and weights Balances and weights shall be calibrated. Calibration and checking of balances and weights shall comply with 5.2.3.2 and 5.2.3.3 respectively. NOTE 1 Balances can incorporate an analogue or a digital display. The

47、balance (and weights if required) selected for a weighing shall enable the mass to be determined to the accuracy required by the test method. If calibration determines that the balance is not suitable for use across its full working range, it shall be labelled to show the upper and lower limits of usable capacity. NOTE 2 Examples of categories of balances are given in Table 1. Annex C relates these categories to most aggregate standard test methods. DIN EN 932-5:2012-05 EN 932-5:2012 (E) 7 Table 1 Examples of categories of balances, their accuracy classes and correspondin