DIN EN 13286-50-2005 Unbound and hydraulically bound mixtures - Part 50 Method for the manufacture of test specimens of hydraulically bound mixtures using Proctor equipment or vibr.pdf

《DIN EN 13286-50-2005 Unbound and hydraulically bound mixtures - Part 50 Method for the manufacture of test specimens of hydraulically bound mixtures using Proctor equipment or vibr.pdf》由会员分享，可在线阅读，更多相关《DIN EN 13286-50-2005 Unbound and hydraulically bound mixtures - Part 50 Method for the manufacture of test specimens of hydraulically bound mixtures using Proctor equipment or vibr.pdf（9页珍藏版）》请在麦多课文档分享上搜索。

1、DEUTSCHE NORM March 2005DIN EN 13286-50 No part of this standard may be reproduced without the prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).English price group 6 www.din.

2、de www.beuth.de06.05 9633460Document comprises 8 pages.Unbound and hydraulically bound mixturesPart 50: Method for the manufacture of test specimens of hydraulically bound mixtures using Proctor equipment or vibrating table compactionEnglish version of DIN EN 13286-50Ungebundene und hydraulisch gebu

3、ndene Gemische Teil 50: Verfahren zur Herstellung von Probekrpern von hydraulisch gebundenen Gemischen durch Verdichtung mit Proctorgert oder VibrationstischA comma is used as the decimal marker.National forewordThis standard has been prepared by CEN/TC 227 Road materials (Secretariat: Germany).The

4、responsible German body involved in its preparation was the Normenausschuss Bauwesen (Building and Civil Engineering Standards Committee), Technical Committee 10.10.00 Hydraulisch gebundene und ungebundene Mischungen.This European Standard is part of a series of standards dealing with unbound and hy

5、draulically bound mix-tures within the scope of the EC Directive on the approximation of the laws, regulations and administrative provisions of the Member States relating to construction products.It should be noted that not all of the DIN Standards dealing with unbound and hydraulically bound mixtur

6、es need yet be withdrawn. This is in keeping with resolution C 88/98 taken by CEN/BT, which states that where packages of EN Standards are concerned, it shall be permitted for the relevant national standards to re-main valid for longer periods than usual, until the EN package has been published in i

7、ts entirety.In the case at hand, the packages cover the DIN EN 14227-1 to DIN EN 14227-5 series (product standards) and the DIN EN 13286-41 to DIN EN 13286-53 series (dealing with test methods).ICS 93.080.20English versionICS 93.080.20Management Centre: rue de Stassart 36, B-1050 BrusselsEuropean Co

8、mmittee for StandardizationComit Europen de NormalisationEuropisches Komitee fr Normung 2004. CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national members.Ref. No. EN 13286-50 : 2004 EEN 13286-50December 2004Unbound and hydraulically bound mixturesPart 50:

9、Method for the manufacture of test specimens of hydraulically bound mixtures using Proctor equipment or vibrating table compactionMlanges traits et mlanges non traits aux liants hydrauliques Par-tie 50: Mthode de confection par compactage avec un appareillage Proctor ou une table vibrante des prouve

10、ttes de matriaux traits au liants hydrauliquesUngebundene und hydraulisch gebun-dene Gemische Teil 50: Verfahren zur Herstellung von Probekrpern von hydraulisch gebundenen Gemischen durch Verdichtung mit Proctorgert oder VibrationstischThis European Standard was approved by CEN on 2004-11-12.CEN mem

11、bers are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.Up-to-date lists and bibliographical references concerning such national standards may be obtained on applicati

12、on to the Management Centre or to any CEN member.The European Standards exist in three ofcial versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notied to the Management Centre has the same status

13、 as the ofcial versions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland, and the United Kingdom.Page 2 EN 13286-50 : 2004Page 3 EN 13286-50 : 2004Page 4 EN 13286-50 : 2004Page 5 EN 13286-50 : 2004Page 6 EN 13286-50 : 2004Page 7 EN 13286-50 : 2004