CEN TR 16625-2013 Flexible sheets for waterproofing - Statistical definition of manufacturer-s limiting value and declared value (MLV and MDV) - 95 % Statistic《防水用柔性薄板 制造商限制价值和申报价值.pdf

《CEN TR 16625-2013 Flexible sheets for waterproofing - Statistical definition of manufacturer-s limiting value and declared value (MLV and MDV) - 95 % Statistic《防水用柔性薄板 制造商限制价值和申报价值.pdf》由会员分享，可在线阅读，更多相关《CEN TR 16625-2013 Flexible sheets for waterproofing - Statistical definition of manufacturer-s limiting value and declared value (MLV and MDV) - 95 % Statistic《防水用柔性薄板 制造商限制价值和申报价值.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationPD CEN/TR 16625:2013Flexible sheets forwaterproofing Statisticaldefinition of manufacturerslimiting value and declaredvalue (MLV and MDV) 95 %StatisticPD CEN/TR 16625:2013 PUBLISHED DOCUMENTNational forewordThis Published Document is the UK implementation of CEN/TR16625:2013

2、.The UK participation in its preparation was entrusted to TechnicalCommittee B/546, Flexible sheets for waterproofing and watervapour control.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessar

3、yprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2013. Published by BSI StandardsLimited 2013ISBN 978 0 580 82828 7ICS 91.100.50Compliance with a British Standard cannot confer immunity fromlegal obligations.This Published Document was pu

4、blished under the authority of theStandards Policy and Strategy Committee on 31 December 2013.Amendments issued since publicationDate Text affectedPD CEN/TR 16625:2013TECHNICAL REPORT RAPPORT TECHNIQUE TECHNISCHER BERICHT CEN/TR 16625 December 2013 ICS 91.100.50 English Version Flexible sheets for w

5、aterproofing - Statistical definition of manufacturers limiting value and declared value (MLV and MDV) - 95 % Statistic Feuilles souples dtanchit - Dfinition statistique de la valeur limite annonce par le fabricant (VLF) et de la valeur dclare par le fabricant (VDF) - Statistique 95 % Abdichtungsbah

6、nen - Statistische Definition des Hersteller-Grenzwertes und des Hersteller-Nennwertes (MLV und MDV) - 95 %-Statistik This Technical Report was approved by CEN on 28 October 2013. It has been drawn up by the Technical Committee CEN/TC 254. CEN members are the national standards bodies of Austria, Be

7、lgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Swit

8、zerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2013 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN nation

9、al Members. Ref. No. CEN/TR 16625:2013 EPD CEN/TR 16625:2013CEN/TR 16625:2013 (E) 2 Contents Page Foreword 3 1 Scope 4 2 Terms and definitions 4 3 Statistical principles 4 3.1 General 4 3.2 MLV/MDV defined by 95 % performance based confidence level 5 Bibliography 6 PD CEN/TR 16625:2013CEN/TR 16625:2

10、013 (E) 3 Foreword This document (CEN/TR 16625) has been prepared by Technical Committee CEN/TC 254 “Flexible sheets for waterproofing”, the secretariat of which is held by NEN. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN

11、and/or CENELEC shall not be held responsible for identifying any or all such patent rights. PD CEN/TR 16625:2013CEN/TR 16625:2013 (E) 4 1 Scope This Technical Report is a guideline for the statistic approach for the definition of MLV/MDV within the declaration of values according to the product stan

12、dards of CEN/TC 254 Flexible sheets for waterproofing (see Bibliography). Characteristics with classes (for example fire behaviour) or pass/fail criteria (for example UV exposure) are not covered by the statistical rules of this report. 2 Terms and definitions For the purposes of the document, the f

13、ollowing terms and definitions apply. NOTE Terms for statistics are common knowledge and are described in different standards (for example ISO 3534-1; ISO/IEC Guide 98-3; ISO/TR 13425). 2.1 manufacturers declared value (MDV)1)nominal value including a double sided specification according to the prod

14、uct standard for a given test method or property 2.2 manufacturers limiting value (MLV)1)nominal value including a single sided specification according to the product standard for a given test method or property Note 1 to entry: The MLV can be a minimum or a maximum value according to statements mad

15、e under product characteristics of the relevant product standard. 2.3 single value value of one test specimen as described within the test standard 2.4 test result result as defined in the test standard Note 1 to entry: The test result is described in the Clause Expression of results of the test sta

16、ndard and reported in the test report. 3 Statistical principles 3.1 General The declaration of the product performance as defined in the product data sheet should be based on statistical interpretation of the factory production control (FPC), the interpretation of the initial type testing (ITT) and

17、the precision of the test methods. For characteristics controlled by FPC tests, where indirect control applies, the statistics of the direct test method apply to the indirect test method including expanded uncertainty. 1) The MLV and MDV definitions are also defined in all product standards given in

18、 the Bibliography of this Technical Report. This Technical Report describes the agreed current position of CEN/TC 254. CEN/TC 254 plans to adjust the statistic definition given in the product standards in accordance with this Technical Report. PD CEN/TR 16625:2013CEN/TR 16625:2013 (E) 5 3.2 MLV/MDV

19、defined by 95 % performance based confidence level The sample shall be taken following the sampling procedure defined by specific product standards. This statistical approach has to be applied either for sampling at the site or within the factory. For a given test method or property used within the

20、factory production control (as defined in the specific product standard) the 95 % performance based confidence level of the test results (as defined in the test method, typically the mean of a set of single measurements) should be within the limits of the MLV/MDV declaration. The continuous characte

21、ristic as the base to calculate the distribution is the test result as defined in the test standard. The precision of the test method is the lowest possible range of the MDV declaration of the datasheet of the manufacturer. 50 % of the precision of the test method is the lowest possible difference b

22、etween the average of the measured values and the MLV single side declaration of the datasheet of the manufacturer. If there is not enough statistical data (less than 50 test results) available for a new product then the statistic of a similar product can be transferred. An outlier can be detected i

23、n accordance to ISO 5725-2 or in a simpler approach if the difference between this single value (the potential outlier) and the mean (as defined in the test method) is more than 4 times the standard deviation determined by the test results of the quality control. In this case the single value of one

24、 specimen is an outlier and this single value can be deleted. NOTE The 95 % confidence interval corresponds to 2 times “experimental standard deviation of the mean” as defined in 4.2 of ISO/IEC GUIDE 983. PD CEN/TR 16625:2013CEN/TR 16625:2013 (E) 6 Bibliography 1 EN 13416 Flexible sheets for waterpr

25、oofing - Bitumen, plastic and rubber sheets for roof waterproofing - Rules for sampling 2 EN 13707 Flexible sheets for waterproofing - Reinforced bitumen sheets for roof waterproofing - Definitions and characteristics 3 EN 13859-1 Flexible sheets for waterproofing - Definitions and characteristics o

26、f underlays - Part 1: Underlays for discontinuous roofing 4 EN 13859-2 Flexible sheets for waterproofing - Definitions and characteristics of underlays - Part 2: Underlays for walls 5 EN 13956 Flexible sheets for waterproofing - Plastic and rubber sheets for roof waterproofing - Definitions and char

27、acteristics 6 EN 13967 Flexible sheets for waterproofing - Plastic and rubber damp proof sheets including plastic and rubber basement tanking sheet - Definitions and characteristics 7 EN 13969 Flexible sheets for waterproofing - Bitumen damp proof sheets including bitumen basement tanking sheets - D

28、efinitions and characteristics 8 EN 13970 Flexible sheets for waterproofing - Bitumen water vapour control layers - Definitions and characteristics 9 EN 13984 Flexible sheets for waterproofing - Plastic and rubber vapour control layers - Definitions and characteristics 10 EN 14695 Flexible sheets fo

29、r waterproofing - Reinforced bitumen sheets for waterproofing of concrete bridge decks and other trafficked areas of concrete - Definitions and characteristics 11 EN 14909 Flexible sheets for waterproofing - Plastic and rubber damp proof courses - Definitions and characteristics 12 EN 14967 Flexible

30、 sheets for waterproofing - Bitumen damp proof courses - Definitions and characteristics 13 ISO/IEC GUIDE 98-3:2008, Uncertainty of measurement Part 3: Guide to the expression of uncertainty in measurement (GUM:1995) 14 ISO 3534-1, Statistics Vocabulary and symbols Part 1: General statistical terms

31、and terms used in probability 15 ISO/TR 13425, Guidelines for the selection of statistical methods in standardization and specification This page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and serv

32、ices.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited.British Standards Institution (BSI)BSI Group Headquarters389 Chiswick High Road London W4 4AL UKAbout usWe bring together business, industry, government, consumers,

33、innovators and others to shape their combined experience and expertise into standards -based solutions.The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choo

34、se standards to help them achieve their goals.Information on standardsWe can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre.Buying standardsYou can

35、buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at where hard copies can also be purchased. If you need international and foreign standards from other Standards Development Organizations, hard copies can be o

36、rdered from our Customer Services team.SubscriptionsOur range of subscription services are designed to make using standards easier for you. For further information on our subscription products go to British Standards Online (BSOL) youll have instant access to over 55,000 British and adopted Europea

37、n and international standards from your desktop. Its available 24/7 and is refreshed daily so youll always be up to date. You can keep in touch with standards developments and receive substantial discounts on the purchase price of standards, both in single copy and subscription format, by becoming a

38、 BSI Subscribing Member. PLUS is an updating service exclusive to BSI Subscribing Members. You will automatically receive the latest hard copy of your standards when theyre revised or replaced. To find out more about becoming a BSI Subscribing Member and the benefits of membership, please visit a M

39、ulti-User Network Licence (MUNL) you are able to host standards publications on your intranet. Licences can cover as few or as many users as you wish. With updates supplied as soon as theyre available, you can be sure your documentation is current. For further information, email .RevisionsOur Britis

40、h Standards and other publications are updated by amendment or revision. We continually improve the quality of our products and services to benefit your business. If you find an inaccuracy or ambiguity within a British Standard or other BSI publication please inform the Knowledge Centre.CopyrightAll

41、 the data, software and documentation set out in all British Standards and other BSI publications are the property of and copyrighted by BSI, or some person or entity that owns copyright in the information used (such as the international standardization bodies) and has formally licensed such informa

42、tion to BSI for commercial publication and use. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permissio

43、n from BSI. Details and advice can be obtained from the Copyright & Licensing Department.Useful Contacts:Customer ServicesTel: +44 845 086 9001Email (orders): Email (enquiries): SubscriptionsTel: +44 845 086 9001Email: Knowledge CentreTel: +44 20 8996 7004Email: Copyright & LicensingTel: +44 20 8996 7070Email: NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW