BS PD ISO TR 17329-2015 Gas cylinders Identification of gas cylinder manufacturer marks and their assigned radio frequency identification (RFID) codes《气瓶 气瓶生产商标记及其分配的射频识别 (RFID) 码的.pdf

《BS PD ISO TR 17329-2015 Gas cylinders Identification of gas cylinder manufacturer marks and their assigned radio frequency identification (RFID) codes《气瓶 气瓶生产商标记及其分配的射频识别 (RFID) 码的.pdf》由会员分享，可在线阅读，更多相关《BS PD ISO TR 17329-2015 Gas cylinders Identification of gas cylinder manufacturer marks and their assigned radio frequency identification (RFID) codes《气瓶 气瓶生产商标记及其分配的射频识别 (RFID) 码的.pdf（44页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationGas cylinders Identification of gas cylinder manufacturermarks and their assigned radio frequency identification (RFID)codesPD ISO/TR 17329:2015National forewordThis Published Document is the UK implementation of ISO/TR 17329:2015.The UK participation in its preparation was

2、entrusted by TechnicalCommittee PVE/3, Gas containers, to Subcommittee PVE/3/7, Gas containers - Gas cylinder (receptacle) operations.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provis

3、ions ofa contract. Users are responsible for its correct application. The British Standards Institution 2015.Published by BSI Standards Limited 2015ISBN 978 0 580 83688 6ICS 23.020.30Compliance with a British Standard cannot confer immunity fromlegal obligations.This Published Document was published

4、 under the authority of theStandards Policy and Strategy Committee on 30 November 2015.Amendments/corrigenda issued since publicationDate Text affectedPUBLISHED DOCUMENTPD ISO/TR 17329:2015 ISO 2015Gas cylinders Identification of gas cylinder manufacturer marks and their assigned radio frequency ide

5、ntification (RFID) codesBouteilles gaz Identification des marques de fabricant de la bouteille de gaz et leurs codes didentification (RFID) de frquences radioTECHNICAL REPORTISO/TR17329Reference numberISO/TR 17329:2015(E)First edition2015-11-01PD ISO/TR 17329:2015ISO/TR 17329:2015(E)ii ISO 2015 All

6、rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2015, Published in SwitzerlandAll rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet

7、 or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeCh. de Blandonnet 8 CP 401CH-1214 Vernier, Geneva, SwitzerlandTel. +41 22 749 01 11Fax +41 22 749 09 47copyright

8、iso.orgwww.iso.orgPD ISO/TR 17329:2015ISO/TR 17329:2015(E)Foreword ivIntroduction v1 Scope . 12 General 13 Explanation of columns . 2Annex A (informative) List of codes and identification marks for gas cylinder manufacturers 3Annex B (informative) Instructions to revise list of manufacturer marks.33

9、Annex C (informative) Current list of codes and identification marks for gas cylinder manufacturers34Bibliography .35 ISO 2015 All rights reserved iiiContents PagePD ISO/TR 17329:2015ISO/TR 17329:2015(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of nat

10、ional standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. Interna

11、tional organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intend

12、ed for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.i

13、so.org/directives). Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document wi

14、ll be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents). Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation on the meaning of ISO specific terms and expres

15、sions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary informationThe committee responsible for this document is ISO/TC 58, Gas cylinders, Subcommittee SC 4, Op

16、erational requirements for gas cylinders.iv ISO 2015 All rights reservedPD ISO/TR 17329:2015ISO/TR 17329:2015(E)IntroductionThe purpose of this Technical Report is to provide the gas cylinder manufacturing industry, the approval authorities, the inspection bodies, the gas industry and all associated

17、 industry branches dealing with gas cylinders a tool for identifying gas cylinders with their manufacturers marks and their assigned radio frequency identification (RFID) codes. ISO 2015 All rights reserved vPD ISO/TR 17329:2015Gas cylinders Identification of gas cylinder manufacturer marks and thei

18、r assigned radio frequency identification (RFID) codes1 ScopeThis Technical Report provides an inventory, as far as known at time of publication, of manufacturers identification marks and their assigned radio frequency identification (RFID) codes according to ISO 21007-1 and ISO 21007-2. The listing

19、 includes marks of existing gas cylinder manufacturers, as well as cylinder manufacturers which have ceased production in the past, but whose cylinders can still be in service today.NOTE It is intended to revise Annex A of this Technical Report from time to time in order to update the list of codes

20、and identification marks of gas cylinder manufacturers in accordance with the progressing commercial and economic development in the cylinder manufacturing industry.Any request for inclusion or modification of these identifications is to be made to the ISO/TC 58/SC 4 Secretariat, who would update th

21、e information in Annex A after consultation with the committee leadership.2 GeneralThere is a general marking requirement by national or international regulations and standards to identify gas cylinders with the cylinder manufacturers identification (name, trademark and/or logo), e.g. by stamp marki

22、ng, or for composite cylinders, by labelling, in order to guarantee their traceability. In certain circumstances, it is very important to enable a distinctive identification of the origin of the cylinder. Normally for a given manufacturer, the identification is specific to a manufacturing location.W

23、hen, in addition to the above marking requirements, the cylinders are identified by radio frequency identification (RFID) codes, the technologies and RFID codes in accordance with ISO 21007 are used. The first three digits of the RFID codes listed in Column 1 of Annex A are the country code as liste

24、d in ISO 3166-1. The subsequent two digits are assigned consecutively in the countrys listing. Once assigned, the RFID code designation does not change.Annex A lists cylinder manufacturers by countries which are currently known to produce or have produced gas cylinders. The list does not claim to be

25、 complete and is valid only as of the date of the publication of this Technical Report. Manufacturers that no longer produce cylinders remain in Annex A as their cylinders could still be in service and need to be identified.It is expected that the manufacturers are using manufacturers marks which id

26、entify unambiguously the manufacturing plant/facility to clearly identify the plant to which the type approval of the concerned cylinder was assigned. Annex A clearly indicates the date when the manufacturing at the old plant/facility ends and the date when the new plant/facility begins manufacturin

27、g cylinders. Names of manufacturers may have changed over time; however, these manufacturers may have continued using the same manufacturers mark provided the approval criteria for the cylinders in question have not changed. Vice versa, a change of the manufacturers mark may have taken place or alte

28、rnative marks may be used by one and the same manufacturer.Clause 3 explains the information provided in each column of Annex A.To provide updates to the list of manufacturers, use the link provided in Annex B for instructions to submit new/revised information. These revisions, once approved by ISO/

29、TC 58/SC 4 and designated with an RFID code, will be provided on Standards Maintenance Portal at the link provided in Annex C.TECHNICAL REPORT ISO/TR 17329:2015(E) ISO 2015 All rights reserved 1PD ISO/TR 17329:2015ISO/TR 17329:2015(E)3 Explanation of columnsThe column entitled “Code” designates the

30、RFID code for a manufacturer.Note This code is assigned by the experts of ISO/TC 58/SC 4.The column entitled “Manufacturer name” designates the official name of the gas cylinder manufacturer. It should be noted that the name may have changed over time.The column entitled “Location of manufacturing p

31、lant/facility” designates the plant/facility responsible for manufacturing and to which the mark is assigned.The column entitled “Year(s) of manufacture” designates the years for which the manufacturers mark(s) were used, if known.For example, “ 1927” means the mark was used inclusive of 1927, “1927

32、 1961” means the mark was used from some time in 1927 to some time during 1961, and “2002 ” means the mark has been used starting some time during 2002 to present.The column entitled “Manufacturers mark” provides the official manufacturers identification that is marked on the cylinder as required by

33、 ISO 13769 (stamp marking 3 in ISO 13769, Table 1).Country: XXXXXCode Manufacturer nameLocation of manufacturing plant/facilityYear(s) of manufacture Manufacturers mark2 ISO 2015 All rights reservedPD ISO/TR 17329:2015ISO/TR 17329:2015(E)Annex A (informative) List of codes and identification marks f

34、or gas cylinder manufacturersThe following list does not claim to be complete and is current as of 2014-07-24.Country: ALGERIACode Manufacturer nameLocation of manufacturing plant/facilityYear(s) of manufacture Manufacturers mark012 01F.E.R.A.P. (Fabrication et entretien de rcipients pression)Algier

35、s Country: ARGENTINACode Manufacturer nameLocation of manufacturing plant/facilityYear(s) of manufacture Manufacturers mark032 01 LAir Liquide Buenos Aires1960 1985032 02 Drago Buenos Aires 1938 MD032 03 Fabricacion Militar 032 04 Gas Carbonic Argentina G.C.A.032 05Gonzalez & Chiesa Changed to Infle

36、x Argentoil S.A.San Luis 1967 INFLEX032 06 Pablo Casale 1958 1986 CASALE032 07 Saravia Y Lopez Buenos Aires 1993LS ISO 2015 All rights reserved 3PD ISO/TR 17329:2015ISO/TR 17329:2015(E)Country: ARGENTINACode Manufacturer nameLocation of manufacturing plant/facilityYear(s) of manufacture Manufacturer

37、s mark032 08 Oxi Luz 032 09 Acetylene Buenos Aires 1972 1992032 10 Miguel Balbona 032 11 R. Batalles S.A. Buenos Aires 1944 032 12 Propulsora San Luis San Luis032 13 Luis Pasquinelli e Hijos Buenos Aires 1947 032 14 Kioshi Compresion Buenos Aires 2005 032 15 Mozart Buenos Aires 1995 032 16 INPROCIL

38、S.A. Entre Rios 2007032 17 CIDEGAS S.A. Buenos Aires 2004 Country: AUSTRALIACode Manufacturer nameLocation of manufacturing plant/facilityYear(s) of manufacture Manufacturers mark036 01Manchester Tank & Equipment COEchuca MANCHESTER036 02 CIG Gas Cylinders 1996 CIG036 03 Luxfer Gas Cylinders Sydney

39、1997 2004 LUXFER4 ISO 2015 All rights reservedPD ISO/TR 17329:2015ISO/TR 17329:2015(E)Country: AUSTRIACode Manufacturer nameLocation of manufacturing plant/facilityYear(s) of manufacture Manufacturers mark040 01Jos. Heiser Changed to Worthington Heiser Changed to Worthington Cylinders GmbHKienberg 1

40、9271927 19611961 19761976 2001HEISER2002 040 02 iSi GmbH Wien1994 (3 alternative symbols used)ISI ISO 2015 All rights reserved 5PD ISO/TR 17329:2015ISO/TR 17329:2015(E)Country: BELGIUMCode Manufacturer nameLocation of manufacturing plant/facilityYear(s) of Manufacture Manufacturers mark056 01S.A. At

41、eliers Belges Runis (formerly S.A. des Ateliers de la Dyle)La Dyle-Louvain 1962056 02 tablissements Champy Antwerp 1940RB056 03 S.A. Comet Mechelen 1980 S.A.COMET.Malines 1980C.M056 04S.A. Standard Van Leer (formerly S.A. Usines Standard)Lierre US.056 05S.A. Des Usines A Tubes de la MeuseFlmalle-Hau

42、te (Lige)TMUCountry: BRAZILCode Manufacturer nameLocation of manufacturing plant/facilityYear(s) of manufacture Manufacturers mark076 01 Worthington Cylinders Itu 2002 2003076 02 Worthington Tank Itu 2002 2003076 03 MAT A/A So Paulo6 ISO 2015 All rights reservedPD ISO/TR 17329:2015ISO/TR 17329:2015(

43、E)Country: CANADACode Manufacturer nameLocation of manufacturing plant/facilityYear(s) of manufacture Manufacturers mark124 01Canadian Cylinder Company, LtdBrantford, Ontario C124 02Engineering Products of Canada LtdBoucherville, QubecE.P.C.L124 03 Forges HPC LteeCap-de-la-Madeleine Qubec124 04Hugh

44、Canning Industries, Inc.Toronto, Ontario124 05Aircom Industries (76) LtdEdmonton, AlbertaM4803124 06Bruin Engineered Parts, Inc.Midland, OntarioBRUINM8802124 07Gas Cylinder TechnologiesTecumseh, OntarioM9001124 08 Kadet Engineering, Inc. Mississauga, Ontario KENG124 09Metal-Flo Corporation Canada Li

45、mitedGuelph, OntarioMFCCL124 10Wolfedale Engineering, LtdMississauga, Ontario 2007 WENG or M8903124 11Steel Cylinder Manufacturing changed to Worthington CylindersTilbury, Ontario 1996 SCM or M80041996 2002 M80042002 M8004 or124 12Dynetek Industries Ltd. changed to Luxfer Canada LimitedCalgary, Albe

46、rta March 1, 2007 M5550March 1, 2007 M0501 ISO 2015 All rights reserved 7PD ISO/TR 17329:2015ISO/TR 17329:2015(E)Country: CHINACode Manufacturer nameLocation of manufacturing plant/facilityYear(s) of manufacture Manufacturers mark156 01Beijing Tianhai Industry Co., Ltd.Beijing 1978 JP156 02Changzhou

47、 Aircraft Manufacture Co., Ltd.Changzhou, Jiangsu Province1980 CAF156 03Chengdu Great High Pressure Vessel Co., Ltd.Chengdu, Sichuan Province1978 CG156 04Chongqing Yifeng High-pressure Container Co., Ltd.Chongqing 1987 YM156 05Juhua Group Corp- Engineering Co., Ltd.Quzhou, Zhejiang Province2002 JG15

48、6 06Ningbo Meike Acetylene Cylinders Co., Ltd.Cicheng Town, Ningbo1984 NB156 07Shanghai Ronghua High-Pressure Vessel Co., Ltd.Shanghai 1979 HT156 08Shanghai Huasheng Enterprises (Group) Co., Ltd.Shanghai 2002 SG156 09Tianjin Tianhai High Pressure Container Co., Ltd.Tianjin 2003 JP1156 10Shanghai Tia

49、nhai Dekun Composite Cylinders Co., Ltd.Shanghai 2005 JP2156 11Langfang Tianhai High Pressure Container Co., Ltd.Langfang, Hebei Province2008 JP3156 12Luxfer Gas Cylinders (Shanghai) Co. Ltd.Shanghai 2005 8 ISO 2015 All rights reservedPD ISO/TR 17329:2015ISO/TR 17329:2015(E)Country: CROATIACode Manufacturer nameLocation of manufacturing plant/facilityYear(s) of manufacture Manufacturers mark891 01Djuro Djako