BS ISO 885-2000 General purpose bolts and screws Metric series Radii under the head《一般用途螺栓和螺钉 米制系列 头下圆角半径》.pdf

《BS ISO 885-2000 General purpose bolts and screws Metric series Radii under the head《一般用途螺栓和螺钉 米制系列 头下圆角半径》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 885-2000 General purpose bolts and screws Metric series Radii under the head《一般用途螺栓和螺钉 米制系列 头下圆角半径》.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BRITISH STANDARD BS ISO 885:2000 ICS 21.06

2、0.10 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW General purpose bolts and screws Metric series Radii under the headThis British Standard, having been prepared under the direction of the Engineering Sector Committee, was published under the authority of the Standards Commi

3、ttee and comes into effect on 15 May 2000 BSI 05-2000 ISBN 0 580 34866 0 BS ISO 885:2000 Amendments issued since publication Amd. No. Date Comments National foreword This British Standard reproduces verbatim ISO 885:2000 and implements it as the UK national standard. The UK participation in its prep

4、aration was entrusted to Technical Committee FME/9, Bolts Nuts present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in

5、the UK. A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled

6、 “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance

7、with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, the ISO title page, pages ii to iii, a blank page, pages 1 and 2, an inside back cover and a back cover. The BSI copyright notice displaye

8、d in this document indicates when the document was last issued.Referencenumber ISO885:2000(E) INTERNATIONAL STANDARD ISO 885 Secondedition 2000-03-01 GeneralpurposeboltsandscrewsMetric seriesRadiiunderthehead Vis dapplicatiion gnrale Srie mtrique Rayon darrondi sous tteISO885:2000(E) ii ISO885:2000(

9、E)iii Foreword ISO(theInternationalOrganizationforStandardization)isaworldwidefederationofnationalstandardsbodies(ISO memberbodies).TheworkofpreparingInternationalStandardsisnormallycarriedoutthroughISOtechnical committees.Eachmemberbodyinterestedinasubjectforwhichatechnicalcommitteehasbeenestablish

10、edhas therighttoberepresentedonthatcommittee.Internationalorganizations,governmentalandnon-governmental,in liaisonwithISO,alsotakepartinthework.ISOcollaboratescloselywiththeInternationalElectrotechnical Commission(IEC)onallmattersofelectrotechnicalstandardization. InternationalStandardsaredraftedina

11、ccordancewiththerulesgivenintheISO/IECDirectives,Part3. DraftInternationalStandardsadoptedbythetechnicalcommitteesarecirculatedtothememberbodiesforvoting. PublicationasanInternationalStandardrequiresapprovalbyatleast75%ofthememberbodiescastingavote. Attentionisdrawntothepossibilitythatsomeoftheeleme

12、ntsofthisInternationalStandardmaybethesubjectof patentrights.ISOshallnotbeheldresponsibleforidentifyinganyorallsuchpatentrights. InternationalStandardISO885waspreparedbyTechnicalCommitteeISO/TC2, Fasteners, Subcommittee SC 7, Reference Standards for fasteners (mainly covering terminology, dimensioni

13、ng, sizes and tolerancing). Thissecondeditioncancelsandreplacesthefirstedition(ISO885:1976),whichhasbeentechnicallyrevised.INTERNATIONALSTANDARD ISO885:2000(E)1 GeneralpurposeboltsandscrewsMetricseriesRadii underthehead 1 Scope ThisInternationalStandardspecifiesthesizesoftheradiiundertheheadandthetr

14、ansitiondiametersofmetric seriesgeneralpurposeboltsandscrews. 2 Dimensions SeeFigure1andTable1. Figure1ISO885:2000(E) 2 Table1Dimensionsr min andd a,max Dimensionsinmillimetres Thread diameter Radius r min Transitiondiameter a d a,max Thread diameter Radius r min Transitiondiameter a d a,max d produ

15、ctgrades A,BandC product grades AandB productgrade C d productgrades A,BandC product grades AandB productgrade C 1,6 0,1 2 39 1 42,4 45,4 2 0,1 2,6 42 1,2 45,6 48,6 2,2 0,1 2,8 45 1,2 48,6 52,6 2,5 0,1 3,1 48 1,6 52,6 56,6 3 0,1 3,6 52 1,6 56,6 62,6 3,5 0,1 4,1 56 2 63 67 4 0,2 4,7 60 2 67 71 4,5 0,

16、2 5,2 64 2 71 75 5 0,2 5,7 6 68 2 75 79 6 0,25 6,8 7,2 72 2 79 83 7 0,25 7,8 8,2 76 2 83 87 8 0,4 9,2 10,2 80 2 87 92 10 0,4 11,2 12,2 85 2 92 97 12 0,6 13,7 14,7 90 2,5 97 102 14 0,6 15,7 16,7 95 2,5 102 108 16 0,6 17,7 18,7 100 2,5 108 113 18 0,6 20,2 21,2 105 2,5 113 118 20 0,8 22,4 24,4 110 2,5

17、118 123 22 0,8 24,4 26,4 115 2,5 123 128 24 0,8 26,4 28,4 120 2,5 128 133 27 1 30,4 32,4 125 2,5 133 138 30 1 33,4 35,4 130 2,5 138 145 33 1 36,4 38,4 140 2,5 148 156 36 1 39,4 42,4 150 2,5 159 166 a Thetransitiondiameterd a isthediameterofthecircleformedatthejunctionoftheradiusrandthebearingsurface

18、ofthehead.BS ISO 885:2000 BSI 389 Chiswick High Road London W4 4AL | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |

19、 | | | | | | | | | | BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amen

20、dment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard w

21、ould inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editio

22、ns of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that

23、have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are a

24、lso available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of t

25、hese and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright,

26、Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standa

27、rd, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070.