BS ISO 1641-2-2011 End mills and slot drills Dimensions and designation of milling cutters with Morse taper shanks《平铣刀和槽钻 莫氏锥柄铣刀的尺寸和标识》.pdf

《BS ISO 1641-2-2011 End mills and slot drills Dimensions and designation of milling cutters with Morse taper shanks《平铣刀和槽钻 莫氏锥柄铣刀的尺寸和标识》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 1641-2-2011 End mills and slot drills Dimensions and designation of milling cutters with Morse taper shanks《平铣刀和槽钻 莫氏锥柄铣刀的尺寸和标识》.pdf（16页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS ISO 1641-2:2011End mills and slot drillsPart 2: Dimensions and designation ofmilling cutters with Morse taper shanksBS ISO 1641-2:2011 BRITISH STANDARDNational forewordThis Br

2、itish Standard is the UK implementation of ISO 1641-2:2011.The UK participation in its preparation was entrusted to TechnicalCommittee MTE/18, Tools tips and inserts for cutting applications.A list of organizations represented on this committee can beobtained on request to its secretary.This publica

3、tion does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. BSI 2011ISBN 978 0 580 64840 3ICS 25.100.20Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the autho

4、rity of theStandards Policy and Strategy Committee on 31 July 2011.Amendments issued since publicationDate Text affectedBS ISO 1641-2:2011Reference numberISO 1641-2:2011(E)ISO 2011INTERNATIONAL STANDARD ISO1641-2Second edition2011-06-15End mills and slot drills Part 2: Dimensions and designation of

5、milling cutters with Morse taper shanks Fraises cylindriques 2 tailles et fraises rainurer Partie 2: Dimensions et dsignation des fraises queue cne Morse BS ISO 1641-2:2011ISO 1641-2:2011(E) COPYRIGHT PROTECTED DOCUMENT ISO 2011 All rights reserved. Unless otherwise specified, no part of this public

6、ation may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva

7、 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2011 All rights reservedBS ISO 1641-2:2011ISO 1641-2:2011(E) ISO 2011 All rights reserved iiiForeword ISO (the International Organization for Standardization) is a worldwide feder

8、ation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that commit

9、tee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordanc

10、e with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires a

11、pproval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 1641-2 was prepared by Technical Co

12、mmittee ISO/TC 29, Small tools, Subcommittee SC 2, High speed steel cutting tools and their attachments. This second edition cancels and replaces the first edition (ISO 1641-2:1978), of which it constitutes a minor revision. In particular, this includes updating of the normative references, addition

13、 of the designation (see Clause 4) and indication of the tolerance classes in accordance with ISO 2768-1 and ISO 2768-2. ISO 1641 consists of the following parts, under the general title End mills and slot drills: Part 1: Milling cutters with cylindrical shanks Part 2: Dimensions and designation of

14、milling cutters with Morse taper shanks Part 3: Dimensions and designation of milling cutters with 7/24 taper shanks BS ISO 1641-2:2011BS ISO 1641-2:2011INTERNATIONAL STANDARD ISO 1641-2:2011(E) ISO 2011 All rights reserved 1End mills and slot drills Part 2: Dimensions and designation of milling cut

15、ters with Morse taper shanks 1 Scope This part of ISO 1641 specifies the general dimensions and designation of the following milling cutters with Morse taper and having a tapped hole: end mills, flat-ended or ball-nosed standard series and long series; slot drills short series and standard series. M

16、orse taper shanks are in accordance with ISO 296 and ISO 5413. It is not applicable to the end mills and slot drills with cylindrical shank, which are dealt with in ISO 1641-1; it is not applicable to those with 7/24 taper shank, which are dealt with in ISO 1641-3. This part of ISO 1641 is not appli

17、cable to solid hardmetal end mills and slot drills. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including

18、 any amendments) applies. ISO 296, Machine tools Self-holding tapers for tool shanks ISO 2768-1, General tolerances Part 1: Tolerances for linear and angular dimensions without individual tolerance indications ISO 2768-2, General tolerances Part 2: Geometrical tolerances for features without individ

19、ual tolerance indications ISO 5413, Machine tools Positive drive of Morse tapers 3 Dimensions 3.1 General All dimensions and tolerances are given in millimetres. Tolerances not specified shall be of tolerance class “m” in accordance with ISO 2768-1 and of class “K” in accordance with ISO 2768-2. BS

20、ISO 1641-2:2011ISO 1641-2:2011(E) 2 ISO 2011 All rights reservedThe values, l1and l2,shall be chosen such that the difference in length (l1 l2) remains constant whatever the series (short, normal or long), according to Table 1. Table 1 Length difference (l1 l2) 4 5 Morse taper no. 1 2 3 Alternative

21、I Alternative II Alternative I Alternative II (l1 l2) 70 85 102 125 148 158 186 3.2 Flat-ended end mills and ball-nosed cylindrical end mills The dimensions of flat-ended end mills and ball-nosed cylindrical end mills shall be in accordance with the dimensions shown in Figure 1 and Table 2. a) Morse

22、 taper nos. 1 to 5 b) Morse taper nos. 4 and 5 Key 1 Morse taper in accordance with ISO 296 2 Morse taper in accordance with ISO 5413 Figure 1 Dimensions of flat-ended end mills and ball-nosed cylindrical end mills BS ISO 1641-2:2011I S O 1641- 2 : 2011( E ) I S O 2011 A l l ri ght s re s e rved 3Ta

23、ble 2 Dimensions of flat-ended end mills and ball-nosed cylindrical end mills Length, l1Length, l2Range of diameters, d1js14 Normalseries Long series From (excluded) Up to (included) Recommendeddiameters, d1Alternative I Alternative II Alternative I Alternative II Normalseries Long series Morse tape

24、rno. 5 6 6 83 94 13 24 6 7,5 7 86 100 16 30 7,5 9,5 8 9 89 108 19 38 9,5 11,8 10 11 92 115 22 45 96 123 1 11,8 15 12 14 111 138 26 53 15 19 16 18 117 148 32 63 123 160 2 19 23,6 20 22 140 177 38 75 23,6 30 25 28 147 192 45 90 155 208 3 30 37,5 32 36 178 201 231 254 53 106 188 211 250 273 4 37,5 47,5

25、 40 45 221 249 283 311 63 125 5 200 223 275 298 4 47,5 60 50 56 233 261 308 336 75 150 60 75 63 248 276 338 366 90 180 5 BS ISO 1641-2:2011ISO 1641-2:2011(E) 4 ISO 2011 All rights reserved3.3 Slot drills The dimensions of slot drills shall be in accordance with the dimensions shown in Figure 2 and T

26、able 3. a) Morse taper nos. 1 to 5 b) Morse taper nos. 4 and 5 Key 1 Morse taper in accordance with ISO 296 2 Morse taper in accordance with ISO 5413 Figure 2 Dimensions of slot drillsBS ISO 1641-2:2011I S O 1641- 2 : 2011( E ) I S O 2011 A l l ri ght s re s e rved 5Table3 Dimensionsof slot drillsLe

27、ngth, l1Length, l2Range of diameters,d1e8Short series Normalseries From (excluded) Up to (included) Recommendeddiameters, d1Alternative I Alternative II Alternative I Alternative II Short series Normalseries Morse taper no. 5 6 6 78 83 8 13 6 7,5 7 80 86 10 16 7,5 9,5 8 9 81 89 11 19 9,5 11,8 10 11

28、83 92 13 22 86 96 1 11,8 15 12 14 101 111 16 26 15 19 16 18 104 117 19 32 107 123 2 19 23,6 20 22 124 140 22 38 23,6 30 25 28 128 147 26 45 134 155 3 30 37,5 32 36 157 180 178 201 32 53 163 186 188 211 4 37,5 47,5 40 45 196 224 221 249 38 63 5 170 193 200 223 4 47,5 60 50 56 203 231 233 261 45 75 60

29、 75 63 211 239 248 276 53 90 5 BS ISO 1641-2:2011ISO 1641-2:2011(E) 6 ISO 2011 All rights reserved4 Designation 4.1 Flat-ended end mills and ball-nosed cylindrical end mills Flat-ended end mills and ball-nosed cylindrical end mills in accordance with this part of ISO 1641 shall be designated by: a)

30、“Flat-ended end mills” or “ball-nosed cylindrical end mills”; b) the reference to this part of ISO 1641, i.e. ISO 1641-2; c) a hyphen; d) the recommended diameter, d1; e) a hyphen; f) the Morse taper number. EXAMPLE 1 A flat-ended end mill in accordance with ISO 1641-2 with recommended diameter d1=

31、8 and Morse taper no. 1 is designated as follows: Flat-ended end mills ISO 1641-2 8 1 EXAMPLE 2 A ball-nosed cylindrical end mill in accordance with ISO 1641-2 with recommended diameter d1= 8 and Morse taper no. 1 is designated as follows: Ball-nosed cylindrical end mills ISO 1641-2 8 1 4.2 Slot dri

32、lls Slot drills in accordance with this part of ISO 1641 shall be designated by: a) “Slot drill”; b) the reference to this part of ISO 1641, i.e. ISO 1641-2; c) a hyphen; d) the recommended diameter, d1; e) a hyphen; f) the Morse taper number. EXAMPLE A slot drill in accordance with ISO 1641-2 with

33、recommended diameter d1= 8 and Morse taper no. 1 is designated as follows: Slot drill ISO 1641-2 8 1 BS ISO 1641-2:2011BS ISO 1641-2:2011ISO 1641-2:2011(E) ICS 25.100.20 Price based on 6 pages ISO 2011 All rights reserved This page deliberately left blankBSI is the independent national body responsi

34、ble for preparing British Standardsand other standards-related publications, information and services. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.British Standards Institution (BSI)raising standards worldwideBSI Group Headquarte

35、rs389 Chiswick High Road London W4 4AL UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 Standards are updated by amendment or revision. Users of British Stan-dards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products an

36、d serv-ices. We would be grateful if anyone finding an inaccuracy or ambiguity whileusing this British Standard would inform the Secretary of the technical com-mittee responsible, the identity of which can be found on the inside frontcover.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001BSI offers

37、Members an individual updating service called PLUS which ensuresthat subscribers automatically receive the latest editions of standards.Tel: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 7001Email: Buying standardsYou may buy PDF and hard copy versions of standards directly using acredit card from the BSI

38、 Shop on the website addition all orders for BSI, international and foreign standards publicationscan be addressed to BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001Email: In response to orders for international standards, it is BSI policy tosupply the BSI implementation of

39、those that have been publishedas British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, Europeanand international standards through its Knowledge Centre.Tel: +44 (0)20 8996 7004 Fax: +44 (0)20 8996 7005Email: Various BSI electronic

40、 information services are also available whichgive details on all its products and services. Tel: +44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048Email: BSI Subscribing Members are kept up to date with standardsdevelopments and receive substantial discounts on the purchase priceof standards. For details

41、 of these and other benefits contact Membership Ad-ministration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards via BritishStandards Online can be found at information about BSI is available on the BSI website at www.bsi- subsists

42、in all BSI publications. BSI also holds the copyright,in the UK, of the publications of the international standardization bodies. Ex-cept as permitted under the Copyright, Designs and Patents Act 1988 no ex-tract may be reproduced, stored in a retrieval system or transmitted in anyform or by any mea

43、ns electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the freeuse, in the course of implementing the standard of necessary details such assymbols, and size, type or grade designations. If these details are to be usedfor any other purpose than implementation then the prior written permissionof BSI must be obtained. Details and advice can be obtained from the Copy-right & Licensing Manager.Tel: +44 (0)20 8996 7070Email: