BS IEC 61935-2-25-2015 Generic cabling systems Specification for the testing of balanced communication cabling in accordance with ISO IEC 11801 Work area with M12 4 poles connector.pdf

《BS IEC 61935-2-25-2015 Generic cabling systems Specification for the testing of balanced communication cabling in accordance with ISO IEC 11801 Work area with M12 4 poles connector.pdf》由会员分享，可在线阅读，更多相关《BS IEC 61935-2-25-2015 Generic cabling systems Specification for the testing of balanced communication cabling in accordance with ISO IEC 11801 Work area with M12 4 poles connector.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationGeneric cabling systems Specification for the testing of balanced communicationcabling in accordance with ISO/IEC 11801Part 2-25: Work area with M12 4 poles connectors Blank detail specificationBS IEC 61935-2-25:2015National forewordThis British Standard is the UK implementa

2、tion of IEC 61935-2-25:2015.The UK participation in its preparation was entrusted to TechnicalCommittee EPL/46, Cables, wires and waveguides, radio frequency connectors and accessories for communication and signalling.A list of organizations represented on this committee can be obtained onrequest to

3、 its secretary.This publication does not purport to include all the necessary provisions ofa contract. Users are responsible for its correct application. The British Standards Institution 2015.Published by BSI Standards Limited 2015ISBN 978 0 580 90497 4ICS 33.120.10Compliance with a British Standar

4、d cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 31 May 2015.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS IEC 61935-2-25:2015IEC 61935-2-25 Edition 1.0 2015-04

5、 INTERNATIONAL STANDARD Generic cabling systems Specification for the testing of balanced communication cabling in accordance with ISO/IEC 11801 Part 2-25: Work area with M12 4 poles connectors Blank detail specification INTERNATIONAL ELECTROTECHNICAL COMMISSION ICS 33.120.10 ISBN 978-2-8322-2652-0

6、Registered trademark of the International Electrotechnical Commission Warning! Make sure that you obtained this publication from an authorized distributor. colourinsideBS IEC 61935-2-25:2015 2 IEC 61935-2-25:2015 IEC 2015 CONTENTS FOREWORD . 3 1 Scope 5 2 Normative references 5 3 Guidance for prepar

7、ation of detail specifications 6 4 Blank detail specification for cords for applications up to 100 MHz 7 BS IEC 61935-2-25:2015IEC 61935-2-25:2015 IEC 2015 3 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ GENERIC CABLING SYSTEMS SPECIFICATION FOR THE TESTING OF BALANCED COMMUNICATION CABLING IN ACCORDA

8、NCE WITH ISO/IEC 11801 Part 2-25: Work area with M12 4 poles connectors Blank detail specification FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object

9、 of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications

10、 (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising

11、 with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, a

12、s nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees i

13、n that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Comm

14、ittees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not prov

15、ide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have the lat

16、est edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whe

17、ther direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is i

18、ndispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 61

19、935-2-25 has been prepared by IEC technical committee 46: Cables, wires, waveguides, R.F. connectors, R.F. and microwave passive components and accessories. The text of this standard is based on the following documents: CDV Report on voting 46/518/CDV 46/544/RVC Full information on the voting for th

20、e approval of this standard can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. BS IEC 61935-2-25:2015 4 IEC 61935-2-25:2015 IEC 2015 A list of all parts in the IEC 61935 series, published under the g

21、eneral title Generic cabling systems Specification for the testing of balanced communication cabling in accordance with ISO/IEC 11801, can be found on the IEC website. Future standards in this series will carry the new general title as cited above. Titles of existing standards in this series will be

22、 updated at the time of the next edition. The committee has decided that the contents of this publication will remain unchanged until the stability date indicated on the IEC website under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be r

23、econfirmed, withdrawn, replaced by a revised edition, or amended. A bilingual version of this publication may be issued at a later date. IMPORTANT The colour inside logo on the cover page of this publication indicates that it contains colours which are considered to be useful for the correct underst

24、anding of its contents. Users should therefore print this document using a colour printer. BS IEC 61935-2-25:2015IEC 61935-2-25:2015 IEC 2015 5 GENERIC CABLING SYSTEMS SPECIFICATION FOR THE TESTING OF BALANCED COMMUNICATION CABLING IN ACCORDANCE WITH ISO/IEC 11801 Part 2-25: Work area with M12 4 pol

25、es connectors Blank detail specification 1 Scope This part of IEC 61935, which is a blank detail specification, describes work area cord with M12 4 poles d-code connectors, as used in the ISO/IEC 24702 and IEC 61918. According to the above cabling specifications, although these cords have only two p

26、airs, their transmission performances, when applicable, are at least category 5 compliant for which the requirements are given in ISO/IEC 11801:2002/AMD2:2010, Clause 13. This specification should be used in conjunction with IEC 61156-1, IEC 61156-6 and IEC 61076-2-101 type D. The blank detail speci

27、fication determines the layout and style for detail specifications describing cords with transmission characteristics up to 100 MHz for digital communications. Detail specifications, based on the blank detail specification, may be prepared by a national organization, a manufacturer, or a user. Test

28、configuration applicable to cords is detailed in IEC 61935-2. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the

29、latest edition of the referenced document (including any amendments) applies. IEC 60794-1-22, Optical fibre cables Part 1-22: Generic specification Basic optical cable test procedures Environmental tests methods IEC 61076-2-101, Connectors for electronic equipment Product requirements Part 2-101: Ci

30、rcular connectors Detail specification for M12 connectors with screw-locking IEC 61156-1:2007, Multicore and symmetrical pair/quad cables for digital communications Part 1: Generic specification IEC 61156-6:2010, Multicore and symmetrical pair/quad cables for digital communications Part 6: Symmetric

31、al pair/quad cables with transmission characteristics up to 1000 MHz Work area wiring Sectional specification IEC 61156-6:2010/AMD1:2012 IEC 61918, Industrial communication networks Installation of communication networks in industrial premises IEC 61935-2:2010, Specification for the testing of balan

32、ced and coaxial information technology cabling Part 2: Cords as specified in ISO/IEC 11801 and related standards BS IEC 61935-2-25:2015 6 IEC 61935-2-25:2015 IEC 2015 IEC 62012-1:2002, Multicore and symmetrical pair/quad cables for digital communications to be used in harsh environment Part 1: Gener

33、ic specification ISO/IEC 11801:2002, Information technology Generic cabling for customer premises ISO/IEC 11801:2002/AMD2:2010 ISO/IEC 24702, Information technology Generic cabling Industrial premises 3 Guidance for preparation of detail specifications It is necessary to keep the transmission charac

34、teristics indicated in the relevant sectional specification for the referenced category number, e.g. 5 and the characteristic impedance. The detail specification shall be written in accordance with the layout of the blank detail specification, which forms part of this standard. When a characteristic

35、 does not apply, then na (for not applicable) should be entered in the appropriate space. When a characteristic applies but a specific value is not considered necessary, then ns (for not specified) should be entered in the appropriate space. When ns is used, the appropriate requirement in the sectio

36、nal specification should apply. The numbers shown in brackets in this and the following pages correspond to the following items of required information, which should be entered in the spaces provided. 1 Name and address of the organization that has prepared the document. 2 IEC document number, issue

37、 number and date of issue. 3 Address of the organization from which the document is available. 4 Related documents. 5 Any other reference to the cable, national reference, trade name, etc. 6 A complete description of the cord which shall include a) type and number of elements; b) nominal impedance;

38、c) screening; d) application; e) specific category of cord, cable and connectors; f) other distinguishing performance characteristics. EXEMPLE 2-pair, shielded twisted pair cable for use in work area wiring, having a nominal impedance of 100 , and meeting the transmission requirements of category 5

39、and the coupling attenuation requirements of type III. 7 Details of the cable material and construction. 8 Special requirements for bending radius or operating temperatures. 9 List of cable characteristics. They are separated into electrical, transmission, mechanical and environmental characteristic

40、s. The recommended environmental severities are derived from the MICE table requirements of ISO/IEC 24702. These recommendations were made to better reflect the cable behaviour. It should be noted that ingress requirements using particles is not applicable to a cable. BS IEC 61935-2-25:2015IEC 61935

41、-2-25:2015 IEC 2015 7 The temperature requirements are addressed in 8. Rapid change of temperature is irrelevant for cables. Electromagnetic requirements coming from the MICE table of ISO/IEC 24702 have been dealt with by using the requirements that are given for transfer impedance, screening attenu

42、ation and coupling attenuation. ESD requirements are considered non-applicable. 10 Appropriate subclause references in the generic specification IEC 61156-1/IEC 61935-2. 11 Appropriate subclause references in the sectional specification IEC 61156-6/ IEC 61935-2. 12 Requirements applicable to this co

43、rd. The values shall meet the requirements of the relevant sectional specification IEC 61156-6 for 2 pairs cable up to 100 MHz. For those limits that are not related to the cord category and for which a choice is proposed, they have to be chosen to meet the related MICE table requirements. 13 Commen

44、ts Relevant remarks. 4 Blank detail specification for cords for applications up to 100 MHz 1 Prepared by: 2 Document: Issue: Date: 3 Available from: 4 Sectional specification for the testing of cords: IEC 61935-2 Blank detail specification: IEC 61935-2-25 5 Additional references: ISO/IEC 11801 6 Cor

45、d description: a) Specific category of cord, cable and connectors b) Nominal impedance c) Connector type d) Cable e) Conductors material f) Screening g) Housing h) MICE 7 Cable assembly construction: IEC 61935-2:2010 4.1 IEC 61156-1:2007 IEC 61156-6:2010 5.2.6 Sheath Material Nominal thicknessa5.2.6

46、 Colour Maximum overall Diameter 5.2.7 Marking 5.2.8 Packaging: Visual inspection IEC 61935-2:2010 5.1 IEC BS IEC 61935-2-25:2015 8 IEC 61935-2-25:2015 IEC 2015 aNot specified in IEC 61156-1. bIt is assumed that a thickness of 0,5 mm is sufficient for spark testing up to 3 kV, thickness larger than

47、0,8 mm is assumed to be sufficient for spark testing up to 5 kV. 8 Minimum bending radius for static bending: mm Minimum bending radius for dynamic bending: mm Temperature range for installation: C Operating temperature range under static conditions: 10 C to +60 C (C1), 25 C to +70 C (C2), 40 C to +

48、70 C (C3) c 9 Characteristics 10 IEC 61156-1:2007 Subclause 11 IEC 61156-6:2010 Subclause 12 Recommended severities/ Requirements 13 Comments Electrical characteristics 6.2 6.2 DC loop resistance 6.2.1 6.2.1 Assumed to be met by design Resistance unbalance 6.2.2 6.2.2 Assumed to be met by design Wir

49、e map IEC 61935-2: 2010 5.2 Transmission characteristics Propagation delay aIEC 61935-2: 2010 5.3 Assumed to be met by design Differential phase delay (skew) aIEC 61935-2: 2010 5.4 Assumed to be met by design Insertion loss IEC 61935-2: 2010 5.5 dB Near-end crosstalk (pair to pair) 6.3.5 IEC 61935-2: 2010 5.7 dB Return loss IEC 61935-2: 2010 5.6 dB TCL 6.3.4 Under c