BS EN ISO 15876-1-2017 Plastics piping systems for hot and cold water installations Polybutene (PB) General《冷热水装置用塑料管道系统 聚丁烯 总则》.pdf

《BS EN ISO 15876-1-2017 Plastics piping systems for hot and cold water installations Polybutene (PB) General《冷热水装置用塑料管道系统 聚丁烯 总则》.pdf》由会员分享，可在线阅读，更多相关《BS EN ISO 15876-1-2017 Plastics piping systems for hot and cold water installations Polybutene (PB) General《冷热水装置用塑料管道系统 聚丁烯 总则》.pdf（20页珍藏版）》请在麦多课文档分享上搜索。

1、BS EN ISO 15876-1:2017Plastics piping systems for hotand cold water installations Polybutene (PB)Part 1: General (ISO 15876-1:2017)BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06BS EN ISO 15876-1:2017 BRITISH STANDARDNational forewordThis British Standard is the UK

2、implementation of EN ISO15876-1:2017. It supersedes BS EN ISO 15876-1:2003 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee PRI/88/2, Plastics piping for pressure applications.A list of organizations represented on this committee can beobtained on reques

3、t to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2017. Published by BSI StandardsLimited 2017ISBN 978 0 580 90295 6ICS 23.040.01; 91.140.60Compliance with a B

4、ritish Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 28 February 2017.Amendments issued since publicationDate Text affectedEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 15876-1

5、 February 2017 ICS 23.040.01; 91.140.60 Supersedes EN ISO 15876-1:2003English Version Plastics piping systems for hot and cold water installations - Polybutene (PB) - Part 1: General (ISO 15876-1:2017) Systmes de canalisations en plastique pour les installations deau chaude et froide - Polybutne (PB

6、) -Partie 1: Gnralits (ISO 15876-1:2017) Kunststoff-Rohrleitungssysteme fr die Warm- und Kaltwasserinstallation - Polybuten (PB) - Teil 1: Allgemeines (ISO 15876-1:2017) This European Standard was approved by CEN on 24 December 2016. CEN members are bound to comply with the CEN/CENELEC Internal Regu

7、lations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN memb

8、er. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. C

9、EN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,

10、 Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2017 CEN All rights of exploita

11、tion in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 15876-1:2017 EBS EN ISO 15876-1:2017EN ISO 15876-1:2017 (E) 3 European foreword This document (EN ISO 15876-1:2017) has been prepared by Technical Committee CEN/TC 155 “Plastics piping systems and ducting

12、systems” the secretariat of which is held by NEN, in collaboration with Technical Committee ISO/TC 138 “Plastics pipes, fittings and valves for the transport of fluids”. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsem

13、ent, at the latest by August 2017, and conflicting national standards shall be withdrawn at the latest by August 2017. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifyin

14、g any or all such patent rights. This document supersedes EN ISO 15876-1:2003. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic

15、, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.

16、Endorsement notice The text of ISO 15876-1:2017 has been approved by CEN as EN ISO 15876-1:2017 without any modification. BS EN ISO 15876-1:2017ISO 15876-1:2017(E)Foreword ivIntroduction v1 Scope . 12 Normative references 13 Terms and definitions, symbols and abbreviated terms 13.1 Terms and definit

17、ions . 23.2 Symbols . 53.3 Abbreviated terms . 64 Classification of service conditions . 65 Material 75.1 General . 75.2 Influence on water intended for human consumption . 85.3 Crystallisation 85.4 Reprocessable material . 86 System performance requirements 8Bibliography 9 ISO 2017 All rights reser

18、ved iiiContents PageBS EN ISO 15876-1:2017ISO 15876-1:2017(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical commit

19、tees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the In

20、ternational Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the d

21、ifferent types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. IS

22、O shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www .iso .org/ patents).Any trade name used in this do

23、cument is information given for the convenience of users and does not constitute an endorsement.For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the World Trade Organization (WTO) principles in th

24、e Technical Barriers to Trade (TBT) see the following URL: www .iso .org/ iso/ foreword .html.ISO 15876-1 was prepared by the European Committee Standardization (CEN) Technical Committee CEN/TC 155, Plastics piping systems and ducting systems, in collaboration with ISO Technical Committee ISO/TC 138

25、, Plastics pipes, fittings and valves for the transport of fluids, Subcommittee SC 2, Plastics pipes and fittings for water supplies, in accordance with the Agreement on technical cooperation between ISO and CEN (Vienna Agreement).This second edition cancels and replaces the first edition (ISO 15876

26、-1:2003), which has been technically revised with the following changes: introduction of polybutene random copolymer (PB-R) and renaming existing polybutene (PB) into polybutene homopolymer (PB-H); revision of specifications for conditioning of samples.It also incorporates the Amendment ISO 15876-1:

27、2003/Amd 1:2007.A list of all parts in the ISO 15876 series can be found on the ISO website.iv ISO 2017 All rights reservedBS EN ISO 15876-1:2017ISO 15876-1:2017(E)IntroductionThe System Standard ISO 15876, of which this document is Part 1, specifies the requirements for a piping system when made fr

28、om polybutene (PB). The piping system is intended to be used for hot and cold water installations.In respect of potential adverse effects on the quality of water intended for human consumption, caused by the product covered by ISO 15876 (all parts): ISO 15876 (all parts) provides no information as t

29、o whether the product may be used without restriction in any of the Member States of the EU or EFTA; it should be noted that, while awaiting the adoption of verifiable European criteria, existing national regulations concerning the use and/or the characteristics of this product remain in force.Requi

30、rements and test methods for material and components of the piping systems are specified in ISO 15876-2 and ISO 15876-3. Characteristics for fitness for purpose (mainly for joints) are covered in ISO 15876-5. ISO/TS 15876-7 gives guidance for the assessment of conformity.This document specifies the

31、general aspects of the plastics piping system.At the date of publication of this standard, System Standards for piping systems of other plastics materials used for the same application include ISO 15874, ISO 15875, ISO 15876, ISO 15877, ISO 21003 and ISO 22391. ISO 2017 All rights reserved vBS EN IS

32、O 15876-1:2017BS EN ISO 15876-1:2017Plastics piping systems for hot and cold water installations Polybutene (PB) Part 1: General1 ScopeThis document specifies the general aspects of polybutene-1 (PB-1) piping systems intended to be used for hot and cold water installations within buildings for the c

33、onveyance of water whether or not intended for human consumption (domestic systems) and for heating systems, under design pressures and temperatures according to the class of application (see Table 1).The designation polybutene is used together with the abbreviation PB throughout this document.This

34、document covers a range of service conditions (application classes) and design pressure and pipe dimension classes. Values of TD, Tmaxand Tmalin excess of those in Table 1 do not apply.NOTE It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects,

35、taking into account their particular requirements and any relevant national regulations and installation practices or codes.It also specifies the test parameters for the test methods referred to in this document.In conjunction with the other parts of ISO 15876, this document is applicable to PB pipe

36、s, fittings, their joints and to joints with components of other plastics and non-plastics materials intended to be used for hot and cold water installations.2 Normative referencesThe following documents are referred to in the text in such a way that some or all of their content constitutes requirem

37、ents of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 472, Plastics VocabularyISO 1043-1, Plastics Symbols and abbreviated terms Part 1: Basic polymers and their specia

38、l characteristicsISO 15876-2, Plastics piping system for hot and cold water installations Polybutene (PB) Part 2: PipesISO 15876-3, Plastics piping system for hot and cold water installations Polybutene (PB) Part 3: FittingsISO 15876-5, Plastics piping system for hot and cold water installations Pol

39、ybutene (PB) Part 5: Fitness for purpose of the system3 Terms and definitions, symbols and abbreviated termsFor the purposes of this document, the terms and definitions, symbols and abbreviated terms given in ISO 472 and ISO 1043-1 and the following apply.INTERNATIONAL STANDARD ISO 15876-1:2017(E) I

40、SO 2017 All rights reserved 1BS EN ISO 15876-1:2017ISO 15876-1:2017(E)ISO and IEC maintain terminological databases for use in standardization at the following addresses: IEC Electropedia: available at h t t p :/ www .electropedia .org/ ISO Online browsing platform: available at h t t p :/ www .iso

41、.org/ obp3.1 Terms and definitions3.1.1 Geometrical terms and definitions3.1.1.1nominal sizeDNnumerical designation of the size of a component, which is a convenient round number, approximately equal to the manufacturing dimensions in millimetres (mm)3.1.1.2nominal sizeDN/ODnominal size, related to

42、outside diameter3.1.1.3nominal outside diameterdnspecified diameter, in millimetres, assigned to a nominal size DN/OD3.1.1.4outside diameter (at any point)demeasured outside diameter through the cross-section at any point of a pipe or spigot end of a fitting, rounded up to the nearest 0,1 mm3.1.1.5m

43、ean outside diameterdemmeasured length of the outer circumference of a pipe or spigot end of a fitting in any cross section divided by pi(, ) 3 142 rounded up to the nearest 0,1 mm3.1.1.6minimum mean outside diameterdem,minminimum value of the mean outside diameter as specified for a given nominal s

44、ize3.1.1.7maximum mean outside diameterdem,maxmaximum value of the mean outside diameter as specified for a given nominal size3.1.1.8mean inside diameter of socketdsmarithmetical mean of two measured inside diameters perpendicular to each other at the midpoint of the socket length2 ISO 2017 All righ

45、ts reservedBS EN ISO 15876-1:2017ISO 15876-1:2017(E)3.1.1.9out-of-roundnessovalitydifference between the measured maximum outside diameter and the measured minimum outside diameter in the same cross-sectional plane of a pipe or spigot end of a fitting, or the difference between the measured maximum

46、inside diameter and the measured minimum inside diameter in the same cross-sectional plane of a socket3.1.1.10nominal wall thicknessennumerical designation of the wall thickness of a component, approximately equal to the manufacturing dimension in millimetres (mm)3.1.1.11wall thickness (at any point

47、)emeasured wall thickness at any point around the circumference of a component, rounded up to the nearest 0,1 mm3.1.1.12minimum wall thickness (at any point)eminminimum wall thickness at any point around the circumference of a component, as specified3.1.1.13maximum wall thickness (at any point)emaxm

48、aximum wall thickness at any point around the circumference of a component, as specified3.1.1.14tolerancepermitted variation of the specified value of a quantity expressed as the difference between the permitted maximum and permitted minimum value3.1.1.15pipe seriesSdimensionless number for pipe des

49、ignation conforming to ISO 4065Note 1 to entry: According to ISO 15876 (all parts), the pipe series S is used as a means for selecting pipe sizes for practical purposes (see ISO 15876-2).3.1.1.16calculated pipe valueScalcvalue for a specific pipe calculated according to the following equation, rounded up to the nearest 0,1 mm:Sdeecalcnnn= - 2wherednis the nominal outside diameter, in millimetres;enis the nominal wall thickness, expressed in millimetres.3.1.2 Terms and definitions related to service conditions ISO 2017 All