BS EN ISO 10806-2004 Pipework - Fittings for corrugated metal hoses《管道工程 波纹状金属软管用配件》.pdf

《BS EN ISO 10806-2004 Pipework - Fittings for corrugated metal hoses《管道工程 波纹状金属软管用配件》.pdf》由会员分享，可在线阅读，更多相关《BS EN ISO 10806-2004 Pipework - Fittings for corrugated metal hoses《管道工程 波纹状金属软管用配件》.pdf（34页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS EN ISO 10806:2003 Incorporating Corrigendum No. 1 Pipework Fittings for corrugated metal hoses The European Standard EN ISO 10806:2003 has the status of a British Standard ICS 23.040.70 BS EN ISO 10806:2003 This British Standard was published under the authority of the Standards

2、Policy and Strategy Committee on 16 January 2004 BSI 30 January 2004 ISBN 0 580 43276 9 National foreword This British Standard is the official English language version of EN ISO 10806:2003, including Corrigendum December 2003. The UK participation in its preparation was entrusted to Technical Commi

3、ttee PSE/12, Metal hoses, hose assemblies, bellows and expansion joints, which has the responsibility to: A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications r

4、eferred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online. This publication does not purport to include all the necessary pr

5、ovisions of a contract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretati

6、on, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the EN ISO title page, the EN ISO foreword page, the ISO title page,

7、pages ii to iv, pages 1 to 23, the Annex ZA page, an inside back cover and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. Date Comments 14987 Corrigendum No. 1 30 January 2004 Revised title o

8、n front cover, corrected EN ISO title and foreword pages and incorporating the Annex ZAEUROPEANSTANDARD NORMEEUROPENNE EUROPISCHENORM ENISO10806 November2003 ICS23.040.70 Incorporating corrigendum December 2003 Englishversion PipeworkFittingsforcorrugatedmetalhoses(ISO 10806:2003) TuyauteriesRaccord

9、spourtuyauxmtalliquesflexibles onduleux(ISO10806:2003) RohrleitungenAnschlussteilefrgewellteMetallschluche (ISO10806:2003) ThisEuropeanStandardwasapprovedbyCENon21October2003. CENmembersareboundtocomplywiththeCEN/CENELECInternalRegulationswhichstipulatetheconditionsforgivingthisEurope an Standardthe

10、statusofanationalstandardwithoutanyalteration.Uptodatelistsandbibliographicalreferencesconcernings uchnational standardsmaybeobtainedonapplicationtotheManagementCentreortoanyCENmember. ThisEuropeanStandardexistsinthreeofficialversions(English,French,German).Aversioninanyotherlanguagemadebytra nslati

11、on undertheresponsibilityofaCENmemberintoitsownlanguageandnotifiedtotheManagementCentrehasthesamestatusasthe official versions. CENmembersarethenationalstandardsbodiesofAustria,Belgium,CzechRepublic,Denmark,Finland,France,Germany,Greece, Hungary,Iceland,Ireland,Italy,Luxembourg,Malta,Netherlands,Nor

12、way,Portugal,Slovakia,Spain,Sweden,SwitzerlandandUn ited Kingdom. EUROPEANCOMMITTEEFORSTANDARDIZATION COMITEUROPENDENORMALISATION EUROPISCHESKOMITEEFRNORMUNG ManagementCentre:ruedeStassart,36B1050Brussels 2003CEN Allrightsofexploitationinanyformandbyanymeansreserved worldwideforCENnationalMembers. R

13、ef.No.ENISO10806:2003ECORRECTED20031217 Foreword Thisdocument(ENISO10806:2003)hasbeenpreparedbyTechnicalCommitteeISO/TC5 “Ferrousmetalpipesandmetallicfittings“incollaborationwithTechnicalCommitteeCEN/TC 342“Metalhoses,hoseassemblies,bellowsandexpansionjoints“,thesecretariatofwhichis heldbyUNI. ThisE

14、uropeanStandardshallbegiventhestatusofanationalstandard,eitherbypublicationof anidenticaltextorbyendorsement,atthelatestbyMay2004,andconflictingnationalstandards shallbewithdrawnatthelatestbyMay2004. AccordingtotheCEN/CENELECInternalRegulations,thenationalstandardsorganizationsof thefollowingcountri

15、esareboundtoimplementthisEuropeanStandard:Austria,Belgium,Czech Republic,Denmark,Finland,France,Germany,Greece,Hungary,Iceland,Ireland,Italy, Luxembourg,Malta,Netherlands,Norway,Portugal,Slovakia,Spain,Sweden,Switzerlandand theUnitedKingdom. Endorsementnotice ThetextofISO10806:2003hasbeenapprovedbyC

16、ENasENISO10806:2003withoutany modifications. NOTENormativereferencestoInternationalStandardsarelistedinAnnexZA(normative). ENISO10806:2003 Reference number ISO 10806:2003(E)NINRETOITALAN ADNATSDR OSI 16080 ceSond deition -300251-11 Pipework Fittings for corrugated metal hoses Tuyauteries Raccords po

17、ur tuyaux mtalliques flexibles onduleux Referecne unbmer OSI 60801:002)E(3 OSI 3002INTERNATIONAL STANDARD ISO 10806 Second edition 2003-11-15 epiPwottiF krsgni c rofoagurrdet latem sesoh Tuyretuaies R accords ruop yutxua tmalqilseu flxeibsel oudnelxu ENISO10806:2003 ii ENISO10806:2003 iiiForeword IS

18、O (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical co

19、mmittee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electro

20、technical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the me

21、mber bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. ISO 10806 was prepared by Technical Committee ISO/TC 5, Ferrous metal pipes and metallic fittings, Subcommittee SC 11, Metal hoses and expansion joints. This secon

22、d edition cancels and replaces the first edition (ISO 10806:1994), which has been technically revised. ENISO10806:2003iv Introduction It was decided to produce a standard under the Vienna agreement on technical cooperation between ISO and the European Committee for Standardization (CEN) in order to

23、maintain one standard. The opportunity was taken to add additional information not available for the first edition of ISO 10806. The major changes are: addition of a clause on design; revision of the type descriptions and the symbols; addition of conical nipples and adaptors; addition of three serie

24、s of fixed flanges; deletion of the PN 16 loose plate flange series. ENISO10806:2003INTENRATIONAL TSANDADR IS:60801 O3002(E)1Pipework Fittings for corrugated metal hoses 1 Scope This International Standard specifies the characteristics of fittings for corrugated metal hose conforming with the requir

25、ements of ISO 10380. This International Standard is also valid for other fittings provided they meet the material, design, assembly and test requirements specified herein. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated refe

26、rences, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 7-1, Pipe threads where pressure-tight joints are made on the threads Part 1: Dimensions, tolerances and designation ISO 228-1, Pipe threads where pre

27、ssure-tight joints are not made on the threads Part 1 : Dimensions, tolerances and designation ISO 724, ISO general-purpose metric screw threads Basic dimensions ISO 4144, Pipework Stainless steel fittings threaded in accordance with ISO 7-1 ISO 4145, Non alloy steel fittings threaded to ISO 7-1 ISO

28、 4200:1991, Plain end steel tubes, welded and seamless General tables of dimensions and masses per unit length ISO 6761, Steel tubes Preparation of ends of tubes and fittings for welding ISO 7005-1:1992, Metallic flanges Part 1: Steel flanges ISO 7268, Pipe components Definition of nominal pressure

29、ISO 7369, Pipework Metal hoses and hose assemblies Vocabulary ISO 10380:2003, Pipework Corrugated metal hoses and hose assemblies EN 1092-1:2001, Flanges and their joints Circular flanges for pipes, valves, fittings and accessories, PN designated Part 1: Steel flanges EN 1333, Pipework components De

30、finition and selection of PN ENISO10806:20032 3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 7369 apply. 4 Information to be supplied by the purchaser 4.1 The purchaser shall state the following in enquiries and orders: a) intended application; b) n

31、ominal size; c) maximum operating pressure; d) materials of construction; e) temperature range; f) type of fitting 1) as specified in Table 1, or 2) as specified by the purchaser. 4.2 Depending on the application, the purchaser shall provide a) product to be conveyed; b) any special information conc

32、erning choice of materials; c) requirements for test certificates; d) any special requirements for packaging. 5 Requirements 5.1 Classification Fittings are classified as follows: a) welded screwed, b) welded stub, c) welded flanged, d) adaptors, and e) those specified in Table 1. ENISO10806:2003 35

33、.2 Materials Materials for the parts of end fittings that are welded or brazed shall be selected from those listed in ISO 10380:2003, Table 1. The use of materials other than these shall be subjected to agreement between the manufacturer and the user. Materials for other parts of the fittings shall

34、be selected from ISO standardized materials and on the basis of their suitability for the conditions under which the hose assemblies will be used. 5.3 Dimensions Fitting dimensions shall be as given in Tables 3 to 13. 5.4 Design 5.4.1 Pressure Welded screwed, welded stub and adaptor fittings shall b

35、e specified to be in accordance with the pressures given in ISO 10380:2003, 5.3.1.1. Pressures for welded flanged fittings shall be as specified in Tables 11 to 15. These pressures are in accordance with ISO 7268 and EN 1333. Where assemblies consist of fittings with different allowable or nominal p

36、ressures, the lower value shall be used for the assembly. 5.4.2 Temperature For temperatures below 20 C or exceeding 50 C, reference shall be made to the derating factors in ISO 10380:2003, Table 3. 5.5 Method of assembly The fittings shall be joined to the hose as specified in ISO 10380:2003, 5.8.

37、6 Type tests 6.1 General All types of welded fitting listed in Table 1 shall be permanently joined to a tube or corrugated metal hose according to the method specified in ISO 10380. They are then assembled as a test assembly, as shown in Table 2. The test medium shall be water unless otherwise agree

38、d by the purchaser. 6.2 Leakage test Subject a test assembly to an hydraulic pressure of 1,5 times the maximum allowable pressure for a minimum of 1 min. The sealing faces of the fittings shall show no signs of visible leakage. 6.3 Burst test Subject a test assembly to an hydraulic pressure applied

39、gradually in increments over a minimum period of 1 min until the assembly fails by leakage or rupture of any of the components, and note the pressure. The burst pressure of the fitting test assembly shall not be less than four times the maximum allowable pressure. ENISO10806:20034 7 Designation The

40、fittings specified in this International Standard shall be designated, in the order indicated, by the following information: a) reference to this International Standard, i.e. ISO 10806; b) symbol (see Table 1); c) nominal size DN (see Tables 3 to 15); d) maximum allowable, nominal pressure (for flan

41、ges), PN; e) grade of material (S for non-alloyed steel or in conformity with ISO 10380 for stainless steel); f) for loose flange, the grade of material of the flanged connection piece shall be indicated after that of the flange material. EXAMPLE 1 A male fitting with a nominal size DN 50 designed f

42、or a pressure of 16 bar and of non-alloyed steel shall be designated as follows: ISO 10806 - M - DN 50 - PN 16 - S EXAMPLE 2 A loose flange with a nominal size DN 50 and a pressure of PN 16, having a weld-on plate collar of stainless steel grade type X 2 CrNi 18 10 and a non-alloyed steel flange, sh

43、all be designated as follows: ISO 10806 - LF/02 - DN 50 - PN 16 - S - X 2 CrNi 18 10 ENISO10806:2003 5Table 1 Types of fittings, their symbols and dimensions Dimensions Diagram Type Symbol Figure Table Fixed male M 1 3 Fixed spherical nipple with swivel nut FS 2 4 Male adaptor for spherical nipple M

44、MS 3 5 Female adaptor for spherical nipple MFS 4 6 Fixed conical nipple with swivel nut aFC 5 7 Male adaptor for conical nipple aMMC 6 8 ENISO10806:20036 Table 1 (continued) Dimensions Diagram Type Symbol Figure Table Female adaptor for conical nipple aMFC 7 9 Tube end T 8 10 Loose flange with weld-

45、on plate collar PN 6; PN 10; PN 16; PN 25; PN 40 (DIN series) LF/02 Loose flange with lapped tube end PN 6; PN 10; PN 16; PN 25; PN 40 (DIN series) LF/03 Loose flange with welding neck collar PN 10; PN 16; PN 25; PN 40 (DIN series) LF/04 9 11 ENISO10806:2003 7Table 1 (continued) Dimensions Diagram T

46、ype Symbol Figure Table Loose hubbed flange for lapped pipe end PN 20; PN 50; PN 110; PN 150; PN 260 (ANSI series) LF/15 10 12 Fixed plate flange for welding PN 6; PN 10; PN 16; PN 25; PN 40; PN 63; PN 100 (DIN series) PN 20 (ANSI series) FF/01 11 13 Fixed welding neck flange PN 6; PN 10; PN 16; PN

47、25; PN 40; PN 63; PN 100 (DIN series) PN 20; PN 50; PN 110; PN 150; PN 260 (ANSI series) FF/11 12 14 Fixed hubbed slip-on flange for welding PN 6; PN 10; PN 16; PN 25; PN 40; PN 63; PN 100 (DIN series) PN 20; PN 50; PN 110; PN 150; PN 260 (ANSI series) FF/12 13 15 aThe combination of Figure 5, Table

48、 7 fittings with those of Figure 6, Table 8 or those of Figure 7, Table 9 should only be supplied and used as complete assemblies, because these fittings are not necessarily interchangeable. ENISO10806:20038 Table 2 Type test fittings Fitting assembled Test assembly M Female fitting in accordance with ISO 4144 or ISO 4145 FS or FC Fitting MMS