BS EN ISO 5845-1-1999 Technical drawings - Simplified representation of the assemby of parts with fasteners - General principles《技术图纸 用紧固件连接的零件组配的简化表示法 一般原则》.pdf

《BS EN ISO 5845-1-1999 Technical drawings - Simplified representation of the assemby of parts with fasteners - General principles《技术图纸 用紧固件连接的零件组配的简化表示法 一般原则》.pdf》由会员分享，可在线阅读，更多相关《BS EN ISO 5845-1-1999 Technical drawings - Simplified representation of the assemby of parts with fasteners - General principles《技术图纸 用紧固件连接的零件组配的简化表示法 一般原则》.pdf（18页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS ENISO 5845-1:1999 Technical drawings Simplified representation of the assembly of parts with fasteners Part1: General principles The European Standard ENISO5845-1:1999 has the status of a BritishStandard ICS 01.100.20; 21.060.01BSENISO5845-1:1999 This BritishStandard, having been

2、 prepared under the directionof the Engineering SectorCommittee, was publishedunder the authority ofthe Standards Committee andcomes into effect on 15October1999 BSI02-2000 ISBN 0 580 35163 7 National foreword This BritishStandard is the English language version of EN ISO5845-1:1999. It is identical

3、 with ISO5845-1:1995. The UK participation in its preparation was entrusted to Technical Committee TDE/4, Engineering drawing, Metrology, precision measurement and other related documentation, which has the responsibility to: aid enquirers to understand the text; present to the responsible internati

4、onal/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. A list of organizations represented on this committee can be obtained on request to its sec

5、retary. Cross-references Attention is drawn to the fact that CEN and CENELEC Standards normally include an annex which lists normative references to international publications with their corresponding European publications. The BritishStandards which implement these international or European publica

6、tions referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provis

7、ions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pagesi andii, theEN ISO title pag

8、e, page 2, the ISO title page, pages ii to iv, pages1 to6 anda back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Amendments issued since publication Amd. No. Date Comments

9、BSENISO5845-1:1999 BSI 02-2000 i Contents Page National foreword Inside front cover Foreword 2 Foreword iii Text of ISO5845-1 1ii blankEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO5845-1 July1999 ICS 01.100.20; 21.060 English version Technical drawings Simplified representation of the ass

10、embly of parts with fasteners Part1:Generalprinciples (ISO5845-1:1995) Dessins techniques Reprsentation simplifie dassemblage de pices au moyen dlments de fixation Partie1: Principes gnraux (ISO5845-1:1995) Technische Zeichnungen Vereinfachte Darstellung von Verbindungselementen fr den Zusammenbau T

11、eil1: Allgemeine Grundlagen (ISO5845-1:1995) This European Standard was approved by CEN on 27May1999. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. U

12、p-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation un

13、der the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, CzechRepublic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Lux

14、embourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and UnitedKingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 1999 CEN All rights of exploitation in any form and

15、by any means reserved worldwide for CEN national Members. Ref. No. ENISO5845-1:1999 EENISO5845-1:1999 BSI 02-2000 2 Foreword The text of the International Standard from Technical Committee ISO/TC10 “Technical drawings, product definition and related documentation” of the International Organization f

16、or Standardization (ISO) has been taken over as an European Standard by CEN/CS. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by January2000, and conflicting national standards shall be withdrawn a

17、t the latest by January2000. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, CzechRepublic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembou

18、rg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and theUnitedKingdom. Endorsement notice The text of the International Standard ISO5845-1:1995 has been approved by CEN as a European Standard without any modification. NOTENormative references to International Standards are listed in Ann

19、ex ZA(normative).EN ISO5845-1:1999 ii BSI 02-2000 Contents Page Foreword iii Introduction 1 1 Scope 1 2 Normative references 1 3 Definitions 1 4 Simplified representation of fasteners 1 4.1 Representation on projection planes normal to the axes of the fasteners 1 4.2 Representation on projection pla

20、nes parallel to the axes of the fastener 1 5 Dimensioning 3 Annex ZA (normative) Normative references to international publications with their relevant European publications 6 Figure 1 1 Figure 2 4 Figure 3 4 Figure 4 4 Figure 5 5 Table 1 Symbolic representation of holes, bolts and rivets to fit in

21、holes 2 Table 2 Symbolic representation of holes 2 Table 3 Symbolic representation of bolts or rivets to fit in holes 3 Descriptors: Drawings, technical drawings, graphic methods, fasteners, graphic symbols, generalities.ENISO5845-1:1999 BSI 02-2000 iii Foreword ISO (the International Organization f

22、or Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has th

23、e right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. Draft In

24、ternational Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least75%of the member bodies casting a vote. International Standard ISO5845-1 was prepared by Technical Committee ISO/TC10, Techn

25、ical drawings, product definition and related documentation, Subcommittee SC6, Mechanical engineering documentation. This first edition of ISO5845-1 is a partial revision of ISO5261:1981, clause3 of which has been technically revised. ISO5845 consists of the following parts, under the general title

26、Technical drawings Simplified representation of the assembly of parts with fasteners: Part1: General principles; Part2: Rivets for aerospace equipment.iv blankENISO5845-1:1999 BSI 02-2000 1 Introduction ISO5845 has been devised to provide a universal means of communication among the various parties

27、involved in the design and manufacture, in general, as well as the installation of fasteners. The representation of fasteners on technical drawings should conform to one of the following two methods, which must meet requirements for microcopying and reproduction: a) conventional drawing of fasteners

28、 (according to ISO128); this method is particularly suitable for drawings containing a small number of fasteners, or when the use of symbols may not provide complete understanding; b) symbolic representation; this method is best suited to drawings containing a large number of fasteners (seeclauses4

29、and5). Requirements within industries vary considerably; in recognition of this fact, ISO5845 is presented in two parts. Part1 is mainly devoted to structural metal work. Part2 is mainly devoted to aerospace equipment. Both are recommended for application to other fields as well. 1 Scope This part o

30、f ISO5845 establishes general principles for the simplified representation of holes, bolts (screws), rivets, etc.on technical drawings. 2 Normative references The following standards contain provisions which, through reference in this text, constitute provisions of this part of ISO5845. At the time

31、of publication, the editions indicated were valid. All standards are subject to revision, and parties to agreements based on this part of ISO5845 are encouraged to investigate the possibility of applying the most recent editions of the standards indicated below. Members of IEC and ISO maintain regis

32、ters of currently valid International Standards. ISO128:1982, Technical drawings General principles of presentation. ISO129:1985, Technical drawings Dimensioning General principles, definitions, methods of execution and special indications. ISO5845-2:1995, Technical drawings Simplified representatio

33、n of the assembly of parts with fasteners Part2: Rivets for aerospace equipment. ISO10209-1:1992, Technical product documentation Vocabulary Part1: Terms relating to technical drawings: general and types of drawings. ISO10209-2:1993, Technical product documentation Vocabulary Part2: Terms relating t

34、o projection methods. 3 Definitions For the purposes of this part of ISO5845, the definitions given in ISO10209-1 and ISO10209-2 apply. 4 Simplified representation of fasteners 4.1 Representation on projection planes normal to the axes of the fasteners In order to represent holes, bolts and rivets o

35、n projection planes normal to their axes, the symbolic representation shall be drawn in continuous thick lines, type A, in accordance with ISO128. The position of the fastener is indicated by a cross (seeFigure 1). Additional information should be indicated in accordance with Table 1 and Table 2 or

36、in accordance with ISO5845-2. A prominent dot may be placed in the centre of the cross in order to facilitate the use of drawing copies as a template (seeexample in Figure 2). The diameter of the dot shall be five times the thickness of the line used for indicating the cross. 4.2 Representation on p

37、rojection planes parallel to the axes of the fastener In order to represent holes, bolts and rivets on projection planes parallel to their axes, the symbolic representation shown in Table 2 and Table 3 shall be adopted. The horizontal line of this symbolic representation shall be drawn in a continuo

38、us thin line, type B; all other parts shall be drawn in a thick line, type A, in accordance with ISO128. Figure 1 ENISO5845-1:1999 2 BSI 02-2000 Table 1 Symbolic representation of holes, bolts and rivets to fit in holes Table 2 Symbolic representation of holes Hole aand bolt or rivet Hole without co

39、untersinking countersunk on near side countersunk on far side countersunk on both sides Drilled and fitted in the workshop Drilled in the workshop and fitted on site Drilled and fitted on site The designation for a hole of diameter13mm is 13, the designation for a bolt with metric screw thread of di

40、ameter12mm and length50mm is M12 50, while that for a rivet of diameter12mm and length50mm is 12 50. a To distinguish bolts and rivets from holes, the correct designation of the hole or fastener shall be given in accordance with the relevant International Standard. EXAMPLE Hole Hole without counters

41、inking countersunk on one side only countersunk on both sides Drilled in the workshop Drilled on siteENISO5845-1:1999 BSI 02-2000 3 Table 3 Symbolic representation of bolts or rivets to fit in holes 5 Dimensioning Dimension lines shall be terminated in accordance with ISO129. 5.1 The extension lines

42、 shall be separated from the symbolic representation of holes, bolts and rivets on projection planes parallel to their axes (seeFigure 2). 5.2 The diameter of holes shall be indicated on a leader line pointing to the symbolic representation of a hole (seeFigure 3). 5.3 To indicate the characteristic

43、s of bolts and rivets, their designation shall be given on a leader line pointing to the symbolic representation in accordance with the relevant International Standard or other specification in use (seeFigure 4). 5.4 The designation of holes, bolts and rivets, when referring to a group of identical

44、elements, can be restricted to one exterior element. In this case the designation shall be preceded by the number of holes, bolts or rivets constituting the group (seeFigure 3 and Figure 4). 5.5 Holes, bolts and rivets equidistant from a centreline may be dimensioned as shown in Figure 3 to Figure 5

45、. Bolt or rivet a Hole Bolt with designated nut position without countersinking countersunk on one side only countersunk on both sides Fitted in the workshop Fitted on site Hole drilled on site and bolt or rivet fitted on site The designation for a bolt with metric screw thread of diameter12mm and l

46、ength50mm is M12 50, while that for a rivet of diameter12mm and length50mm is 12 50. a To distinguish bolts from rivets, the correct designation of the fastener shall be given in accordance with the relevant International Standard. EXAMPLEENISO5845-1:1999 4 BSI 02-2000 Figure 2 Figure 3 Figure 4 ENI

47、SO5845-1:1999 BSI 02-2000 5 Figure 5 ENISO5845-1:1999 6 BSI 02-2000 Annex ZA(normative) Normative references to international publications with their relevant European publications This European Standard incorporates by dated or undated reference, provisions from other publications. These normative

48、references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references

49、 the latest edition of the publication referred to applies. Publication Year Title EN Year ISO10209-2 1993 Technical product documentation Vocabulary Part2: Terms relating to projection methods EN ISO10209-2 1996blankBS ENISO 5845-1:1999 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.