BS EN 60715-2001 Dimensions of low-voltage switchgear and controlgear - Standardized mounting on rails for mechanical support of electrical devices in switchgear and controlgear in.pdf

《BS EN 60715-2001 Dimensions of low-voltage switchgear and controlgear - Standardized mounting on rails for mechanical support of electrical devices in switchgear and controlgear in.pdf》由会员分享，可在线阅读，更多相关《BS EN 60715-2001 Dimensions of low-voltage switchgear and controlgear - Standardized mounting on rails for mechanical support of electrical devices in switchgear and controlgear in.pdf（28页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS EN 60715:2001 IEC 60715:1981: +A1:1995 Dimensions of low- voltage switchgear and controlgear Standardized mounting on rails for mechanical support of electrical devices in switchgear and controlgear installations The European Standard EN 60715:2001 has the status of a British Sta

2、ndard ICS 29.130.20 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBS EN 60715:2001 This British Standard, having been prepared under the direction of the Electrotechnical Sector Committee, was published under the authority of the Standards Committee and comes into effect on 1

3、5 August 2001 BSI 08-2001 ISBN 0 580 37895 0 National foreword This British Standard is the official English language version of EN 60715:2001. It is identical with IEC 60715:1981:+A1:1995. The UK participation in its preparation was entrusted by Technical Committee PEL/17,Switchgear controlgear and

4、 HV-LV co-ordination, to Subcommittee PEL/17/2, Low voltage switchgear and controlgear, which has the responsibility to: A list of organizations represented on this subcommittee can be obtained on request to its secretary. From 1 January 1997, all IEC publications have the number 60000 added to the

5、old number. For instance, IEC 27-1 has been renumbered as IEC 60027-1. For a period of time during the change over from one numbering system to the other, publications may contain identifiers from both systems. Cross-references The British Standards which implement international or European publicat

6、ions referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisi

7、ons of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/European committee any enquiries o

8、n the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 25 and a back cover.

9、The BSI copyright date displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. Date CommentsEUROPEAN STANDARD EN 60715 NORME EUROPENNE EUROPISCHE NORM May 2001 CENELEC European Committee for Electrotechnical Standardization Comit Europen d

10、e Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B - 1050 Brussels 2001 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 60715:2001 E ICS 29.120.60 English v

11、ersion Dimensions of low-voltage switchgear and controlgear - Standardized mounting on rails for mechanical support of electrical devices in switchgear and controlgear installations (IEC 60715:1981 + A1:1995) Dimensions de lappareillage basse tension - Montage normalis sur profils-supports pour le s

12、upport mcanique des appareils lectriques dans les installations dappareillage basse tension (CEI 60715:1981 + A1:1995) Abmessungen von Niederspannungsschaltgerten - Genormte Tragschienen fr die mechanische Befestigung von elektrischen Gerten in Schaltanlagen (IEC 60715:1981 + A1:1995) This European

13、Standard was approved by CENELEC on 2000-04-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references con

14、cerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member int

15、o its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norw

16、ay, Portugal, Spain, Sweden, Switzerland and United Kingdom.Foreword The text of the International Standard IEC 60715:1981 and its amendment 1:1995, prepared by SC 17B, Low-voltage switchgear and controlgear, of IEC TC 17, Switchgear and controlgear, was submitted to the formal vote and was approved

17、 by CENELEC as EN 60715 on 2000-04-01 without any modification. The following dates were fixed: latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2001-10-01 latest date by which the national standards conflict

18、ing with the EN have to be withdrawn (dow) 2003-04-01 _ Endorsement notice The text of the International Standard IEC 60715:1981 and its amendment 1:1995 was approved by CENELEC as a European Standard without any modification. _ EN60715:20012CONTENTS Page Preface .4 Introduction.5 Clause 1 Scope.5 2

19、 Object.6 3 Functional requirements .6 4 Standard dimensions 6 Appendix A - Steel mounting rails .12 Appendix B - Application guide19 EN60715:2001 BSI082001 3EN60715:20014 1002:51706NE4BSI082001EN60715:20015BSI082001EN60715:20016BSI082001EN60715:20017BSI082001EN60715:20018BSI082001EN60715:20019BSI08

20、2001EN60715:200110BSI082001EN60715:200111BSI082001EN60715:200112BSI082001EN60715:200113BSI082001EN60715:200114BSI082001EN60715:200115BSI082001EN60715:200116BSI082001EN60715:200117BSI082001EN60715:200118 1002:51706NE81 1002:51706NE81 EN60715:200181BSI082001EN60715:200119BSI082001EN60715:200120BSI0820

21、01EN60715:200121BSI082001EN60715:200122BSI082001EN60715:200123BSI082001EN60715:200124BSI082001EN60715:200125BSI082001BS EN 60715:2001 IEC 60715:1981: +A1:1995 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent national body responsible for preparing Bri

22、tish Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is

23、 the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front

24、cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addresse

25、d to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. Standards are also available from the BSI website at http:/www.bsi-. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless oth

26、erwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products

27、 and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administr

28、ation. Tel: 020 8996 7002. Fax: 020 8996 7001. Further information about BSI is available on the BSI website at http:/www.bsi-. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as pe

29、rmitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the cour

30、se of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070.