BS EN 16927-2017 Mini-pools Specific requirements including safety and test methods for mini-pools《迷你泳池 迷你泳池的特殊要求 包括安全和试验方法》.pdf

《BS EN 16927-2017 Mini-pools Specific requirements including safety and test methods for mini-pools《迷你泳池 迷你泳池的特殊要求 包括安全和试验方法》.pdf》由会员分享，可在线阅读，更多相关《BS EN 16927-2017 Mini-pools Specific requirements including safety and test methods for mini-pools《迷你泳池 迷你泳池的特殊要求 包括安全和试验方法》.pdf（34页珍藏版）》请在麦多课文档分享上搜索。

1、BS EN 16927:2017Mini-pools Specificrequirements including safetyand test methods for mini-poolsBSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06BS EN 16927:2017 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 16927:2017. The UK pa

2、rticipation in its preparation was entrusted to TechnicalCommittee SW/136/8, Swimming pools and aquatic equipment. A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract

3、. Users are responsible for its correct application. The British Standards Institution 2017.Published by BSI Standards Limited 2017ISBN 978 0 580 91355 6 ICS 97.220.10 Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the autho

4、rity of the Standards Policy and Strategy Committee on 28 February 2017.Amendments/corrigenda issued since publicationDate T e x t a f f e c t e dBS EN 16927:2017EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 16927 February 2017 ICS 97.220.10 English Version Mini-pools - Specific requirements

5、including safety and test methods for mini-pools Piscinettes - Exigences spcifiques, exigences de scurit et mthodes dessai pour piscinettes Mini-Pools - Spezielle Anforderungen einschlielich Sicherheit und Prfverfahren fr Mini-Pools This European Standard was approved by CEN on 21 December 2016. CEN

6、 members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on appl

7、ication to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Ma

8、nagement Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Lat

9、via, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Av

10、enue Marnix 17, B-1000 Brussels 2017 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 16927:2017 EBS EN 16927:2017EN 16927:2017 (E) 2 Contents Page European foreword . 3 Introduction 4 1 Scope 5 2 Normative references 5 3 Terms and

11、definitions . 5 4 General requirements and test methods . 10 4.1 General . 10 4.2 Mini-pools with frame-supported walls and rigid walls 10 4.2.1 Resistance to horizontal deformation 10 4.2.2 Resistance to vertical deformation 11 4.2.3 Bursting strength . 11 4.3 Mini-pools with self-stabilizing or in

12、flatable walls . 12 4.3.1 Capacity to stop an overflow 12 4.3.2 Inflatable compartments . 13 4.3.3 Stability in the event of deflation of the upper tube of mini-pool with self-stabilizing walls 13 4.3.4 Bursting strength . 14 4.4 Tolerances 14 4.5 Minimum performance requirements for structural mate

13、rials . 14 4.5.1 General . 14 4.5.2 Specific requirements and testing for corrosion resistance 14 4.6 Injury risks . 15 4.6.1 Small elements, edges and corners 15 4.6.2 Permissible openings . 16 4.7 Accessibility . 17 5 Instructions for the consumer . 18 5.1 General principles 18 5.2 Point-of-purcha

14、se information . 18 5.3 Installation and maintenance information . 19 5.4 On-product warnings 19 Annex A (informative) Examples of mini-pool dimensions . 21 Annex B (informative) Safety information in the owners manual and instruction sheets accompanying the mini-pool 23 Annex C (normative) Methods

15、of test for entrapment . 25 C.1 Head and neck entrapment 25 C.2 Finger and toe entrapment . 26 C.3 Other body parts entrapment 26 Bibliography . 28 BS EN 16927:2017EN 16927:2017 (E) 3 European foreword This document (EN 16927:2017) has been prepared by Technical Committee CEN/TC 402 “Domestic pools

16、and spas”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by August 2017, and conflicting national standards shall be withdrawn at the latest by August 201

17、7. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such patent rights. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the fol

18、lowing countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands,

19、 Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 16927:2017EN 16927:2017 (E) 4 Introduction This document specifies general and safety requirements and test methods that are applicable to domestic mini-pools. The users o

20、f this standard could be either in a business to consumer (B to C) relationship, such as manufacturers, retailers, etc. or in a business to business (B to B) relationship, such as manufacturers, suppliers, distributors, local authorities, etc. Safe products are the basis of the consumers safety and

21、therefore, this European standard takes into account the following topics: product safety requirements; safe construction and installation; safe use, including information and safety warnings for consumers (e.g. “Dont leave your child unattended in the mini-pool”). It should be highlighted that the

22、risk of drowning, particularly for children under 5 years of age, continues to exist during recreational activities in mini-pools, despite their smaller size and volume of water compared to swimming pools. Attention should also be paid to environmental aspects, according to CEN Guide 4 (e.g. minimiz

23、ing water being misused when the water is regularly replaced in mini-pools, etc.). BS EN 16927:2017EN 16927:2017 (E) 5 1 Scope This European Standard specifies the general safety and quality requirements and test methods for domestic mini-pools. These requirements and test methods are applicable to

24、mini-pool structures, including their installation and possible means of access. This European Standard does not apply to: pools for public use covered by EN 15288-1; swimming pools for domestic use covered by EN 16582 series; spas for domestic or public use; paddling pools according to EN 71-8 2 No

25、rmative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendment

26、s) applies. EN 71-1, Safety of toys - Part 1: Mechanical and physical properties EN 335, Durability of wood and wood-based products - Use classes: definitions, application to solid wood and wood-based products EN 350, Durability of wood and wood-based products - Testing and classification of the dur

27、ability to biological agents of wood and wood-based materials EN 351-1, Durability of wood and wood-based products - Preservative-treated solid wood - Part 1: Classification of preservative penetration and retention EN 460, Durability of wood and wood-based products - Natural durability of solid woo

28、d - Guide to the durability requirements for wood to be used in hazard classes EN 16582-1:2015, Domestic swimming pools - Part 1: General requirements including safety and test methods EN ISO 4628-3, Paints and varnishes - Evaluation of degradation of coatings - Designation of quantity and size of d

29、efects, and of intensity of uniform changes in appearance - Part 3: Assessment of degree of rusting (ISO 4628-3) EN ISO 9227, Corrosion tests in artificial atmospheres - Salt spray tests (ISO 9227) ISO 20712-1, Water safety signs and beach safety flags Part 1: Specifications for water safety signs u

30、sed in workplaces and public areas 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. BS EN 16927:2017EN 16927:2017 (E) 6 3.1 mini-pool non permanently installed artificial aboveground basin: with a maximum wall height 50mm, apply a force of 900 N v

31、ertically in the axis of the wall, at the position most likely to fail, for 5 min. The test shall be performed on a 300 mm diameter disc. If the thickness of the top wall is 50 mm, apply a force of 300 N vertically in the axis of the wall, at the position most likely to fail, for 5 min. The test sha

32、ll be performed on a 300 mm diameter disc. 4.2.3 Bursting strength 4.2.3.1 General The bursting strength test defined in 4.2.3.3 is performed after carrying out the resistance tests for horizontal deformation (4.2.1.2) and vertical deformation (4.2.2.2). 4.2.3.2 Requirements On completion of the tes

33、t defined in 4.2.3.3, the pool shall not burst and shall not suffer any permanent deformation affecting the products resistance. 4.2.3.3 Test methods Fill the mini-pool with water to the maximum filling level recommended by the manufacturer. BS EN 16927:2017EN 16927:2017 (E) 12 Bring a plastic cylin

34、drical barrel with a diameter between 400 mm and 500 mm, a capacity of 120 l and a total weight of 120 kg including ballast, in a vertical position, above the pool. The drop height, compared to the water level recommended by the manufacturer, is +400600 mm. Position the central axis of the barrel ve

35、rtically aligned with the inner edge (on the water side) of the mini-pool. Apply pressure on the upper edge of the barrel so as to tip the barrel into the pool under its own inertia, at the most unfavourable point. Tip it into the water (see Figure 6) Dimensions in millimetres Key 1 barrel support 2

36、 barrel 3 vertical axis of the barrel 4 tip over 5 rotation point for tip over 6 coping 7 wall 8 water level Figure 6 Bursting strength test 4.3 Mini-pools with self-stabilizing or inflatable walls 4.3.1 Capacity to stop an overflow 4.3.1.1 Requirement On completion of the tests described in 4.3.1.2

37、 and in 4.3.1.3, the mini-pool shall not collapse and lose its water retention capability. 4.3.1.2 Mini-pool overflow Install the mini-pool, according to the manufacturers instructions, on a flat horizontal ground (maximum slope allowed is 5 mm/m); BS EN 16927:2017EN 16927:2017 (E) 13 Fill the mini-

38、pool until it overflows with a flow rate of 2,5 m3/h minimum and allow it to overflow for 1 min. 4.3.1.3 Behaviour test of the wall under load Fill the mini-pool with water to the maximum filling level recommended by the manufacturer. Place on the tube, at the most unfavourable place, a 0,50 m long

39、rigid half pipe (made of light material e.g. PVC) with a minimum inside diameter of 0,25 m (adapted to the tube size) ballasted with a strap carrying one 40 kg weight on each end (one on the inside of the pool and the other on the outside) (see Figure 7). Maintain the load for 3 s at the tubes maxim

40、um deflection, the weights being liable to touch the ground. Lift the load up immediately after 3 s making sure that the loading device does not interfere during this operation. NOTE In the case of mini-pools fitted with a strut, this test is performed at the most unfavourable point. The weights sho

41、uld touch the ground as late as possible (e.g. by reducing the length of the straps) Key 1 half pipe 2 weights 3 ground clearence 4 strap Figure 7 Behaviour test of the wall under load 4.3.2 Inflatable compartments All of the air inlets provided for inflation shall be fitted with caps permanently se

42、cured on an accessible part of each inflatable compartment of the mini-pool. Once this part is inflated, the caps located inside the mini-pool shall be able to be pushed back inside the upper part so that they do not protrude from the surface by more than 5 mm. The caps of the inflation ports should

43、 not be able to become detached and should be protected against accidental removal. The valves shall be fitted in order to prevent an instantaneous deflation. 4.3.3 Stability in the event of deflation of the upper tube of mini-pool with self-stabilizing walls 4.3.3.1 Requirement On completion of the

44、 test described in 4.3.3.2, the mini-pool with self-stabilizing walls shall not collapse. BS EN 16927:2017EN 16927:2017 (E) 14 4.3.3.2 Test method Install the mini-pool, according to the manufacturers instructions, on flat horizontal ground (maximum slope allowed is 5 mm/m). Fill the pool with water

45、 up to the level normally recommended in the installation manual. Open the inflatable part by its normal air release device until it is apparently fully deflated. 4.3.4 Bursting strength 4.3.4.1 Requirement On completion of the test defined in 4.3.4.2, the mini-pool with self-stabilizing walls shall

46、 not burst and shall not present any permanent deformation affecting the products resistance. 4.3.4.2 Test method Fill the mini-pool with water to the maximum filling level recommended by the manufacturer. Bring a plastic cylindrical barrel with a diameter between 400 mm and 500 mm, a capacity of 12

47、0 l and a total weight of 120 kg including ballast, in vertical position, above the pool. The drop height, compared to the water level recommended by the manufacturer, is +400600 mm. Position the central axis of the barrel vertically aligned with the inner edge (on the water side) of the mini-pool.

48、Apply pressure on the upper edge of the barrel so as to tip the barrel into the pool under its own inertia, at the most unfavourable point. Tip it into the water. 4.4 Tolerances The indicated dimensions and measurements are given with a tolerance of 3 % (unless otherwise indicated). Mini-pools with

49、self-stabilizing or inflatable walls commonly have larger acceptable tolerances. 4.5 Minimum performance requirements for structural materials 4.5.1 General The structural design and materials shall be in accordance with accepted structural engineering practices. Selection of materials for the construction of the mini-pool shall be conducted under consideration of external influences, including but not limited to, temperature, UV, chemicals, etc., when appropriate, that may influence the structural integrity o