BS EN 16064-2011 Packaging Rigid plastic containers PET finish 30 25 H (18 5)《包装 硬质塑料容器 PET涂膜30 25 H(18 5)》.pdf

《BS EN 16064-2011 Packaging Rigid plastic containers PET finish 30 25 H (18 5)《包装 硬质塑料容器 PET涂膜30 25 H(18 5)》.pdf》由会员分享，可在线阅读，更多相关《BS EN 16064-2011 Packaging Rigid plastic containers PET finish 30 25 H (18 5)《包装 硬质塑料容器 PET涂膜30 25 H(18 5)》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN 16064:2011Packaging Rigid plasticcontainers PET finish 30/25High (18,5)Copyright European Committee for Standardization Provided by IHS under license with CENNot for Resale

2、No reproduction or networking permitted without license from IHS-,-,-BS EN 16064:2011 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 16064:2011.The UK participation in its preparation was entrusted to TechnicalCommittee PKW/0/-/10, Packaging - Plastics.A list o

3、f organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2012ISBN 978 0 580 69992 4ICS 55.100Com

4、pliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 31 January 2012.Amendments issued since publicationDate Text affectedCopyright European Committee for Standardization

5、Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN 16064:2011EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 16064 November 2011 ICS 55.100 English Version Packaging - Rigid plastic containers - PET finish 30/25 High (1

6、8,5) Emballage - Rcipients en plastique rigide - Bague PET 30/25 Haute (18,5) Verpackung - Kunststoffbehltnisse - PET-Verschlussmundstck 30/25 hoch (18,5) This European Standard was approved by CEN on 29 October 2011. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which st

7、ipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This Europea

8、n Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are t

9、he national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden,

10、Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2011 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref.

11、 No. EN 16064:2011: ECopyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN 16064:2011EN 16064:2011 (E) 2 Contents Page Foreword 3Introduction .41 Scope 52 Dimensions .53 Requirem

12、ents .5Bibliography 7Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN 16064:2011EN 16064:2011 (E) 3 Foreword This document (EN 16064:2011) has been prepared by Technical Com

13、mittee CEN/TC 261 “Packaging”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 2012, and conflicting national standards shall be withdrawn at the lat

14、est by May 2012. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national stand

15、ards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, P

16、oland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN 16064:2011EN 16064:2011 (E)

17、 4 Introduction This European Standard is based on CE.T.I.E. (International Technical Centre for Bottling and Packaging) data sheet GME 30.21 (2007) 1. Efficient packaging is of great importance for the distribution and the protection of goods. Insufficient or Inappropriate packaging can lead to dam

18、age or wastage of the contents of the pack. Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN 16064:2011EN 16064:2011 (E) 5 1 Scope This European Standard specifies the dimen

19、sions and requirements of the 30 mm tall screw finish with three (3) thread starts for flat waters and non-carbonated beverages. This finish can be used for aseptic filling and filling with introduction of nitrogen. The dimension (18,5) is the height in millimetres from the top of finish to the bott

20、om of the support ledge. This finish is designed to take a tamper evident plastic closure only. During first opening, the tamper evident band will separate from the closure shell and stay on a one-way bottle neck or like bottles in the returnable market, the tamper evident band will tear but will re

21、main connected to the closure shell. 2 Dimensions 2.1 The design and dimensions of the finish shall be as shown in Figure 1. NOTE Another version exists with C = 25 mm and A = 30,3 mm. 2.2 Dimensions of the 3 thread starts 120 apart. 120 of full depth thread per lead R 9,6 thread lead-in R 2,5 threa

22、d run-out Lead: 9 mm (travel per turn) 2.3 General tolerance for other radii: 0,13 mm. 2.4 Weight on height 18,5 mm: 3,92 g (density = 1,335). 3 Requirements The following requirements apply. This finish is a top, side and inside seal finish. This finish shall be smooth and free of any defects that

23、will contribute to leaks. Flash shall not exceed 0,13 mm per side, and shall not be continuous. On the blown bottle, the control diameter C shall be free of any defects up to 4 mm down for the internal bore and across the sealing surface of the finish. Requirements for good closure application on fi

24、nish: 0,13 mm max. out-of-parallel sealing surface with neck support ledge is allowed; an offset or vertical mismatch of thread is not to exceed 0,10 mm at the mould seam. T dimension is not measured in the depressed area. Variations in E are to follow uniformly those of T. No overhang allowed at an

25、y point in 360 between F and G. A flash to 0,15 mm maximum step is allowable on one side only. G does not exceed E. Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN 16064:20

26、11EN 16064:2011 (E) 6 Dimensions in millimetres Key 1 start thread 5 above parting line 2 below parting line 6 thread lead-in 3 thread starts 120 apart 7 thread run-out 4 straight NOTE * = includes ovality. Figure 1 Design and dimensions of the finish Copyright European Committee for Standardization

27、 Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN 16064:2011EN 16064:2011 (E) 7 Bibliography 1 CE.T.I.E. data sheet GME 30.21 PET finish 30/25 H (18,5) 2007 C.E.T.I.E. : International Technical Centre for Bottling and rela

28、ted Packaging 112 114 rue La Botie 75008 Paris www.cetie.org Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-This page deliberately left blankCopyright European Committee for Sta

29、ndardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-This page deliberately left blankCopyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking pe

30、rmitted without license from IHS-,-,-BSI is the independent national body responsible for preparing British Standards and other standards-related publications, information and services. It presents the UK view on standards in Europe and at the international level. BSI is incorporated by Royal Charte

31、r. British Standards and other standardisation products are published by BSI Standards Limited.British Standards Institution (BSI)raising standards worldwideBSI389 Chiswick High Road London W4 4AL UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 Standards and PASs are periodically updated by amendment o

32、r revision. Users of British Standards and PASs should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using British Standards woul

33、d inform the Secretary of the technical committee responsible, the identity of which can be found on the inside frontcover. Similary for PASs, please notify BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001BSI offers BSI Subscribing Members an individual updating service called

34、 PLUS which ensures that subscribers automatically receive the latest editions of British Standards and PASs.Tel: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 7001Email: Buying standardsYou may buy PDF and hard copy versions of standards directly using acredit card from the BSI Shop on the website addit

35、ion all orders for BSI, international and foreign standards publicationscan be addressed to BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001Email: In response to orders for international standards, BSI will supply the British Standard implementation of the relevant internation

36、al standard, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, Europeanand international standards through its Knowledge Centre.Tel: +44 (0)20 8996 7004 Fax: +44 (0)20 8996 7005Email: BSI Subscribing Members are kept up to date with standards de

37、velopments and receive substantial discounts on the purchase priceof standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards and PASs via British Standards

38、 Online can be found at information about British Standards is available on the BSI website at www.bsi- the data, software and documentation set out in all British Standards and other BSI publications are the property of and copyrighted by BSI, or some person or entity that own copyright in the inf

39、ormation used (such as the international standardisation bodies) has formally licensed such information to BSI for commerical publication and use. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any fo

40、rm or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used

41、for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Department.Tel: +44 (0)20 8996 7070Email: Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-