BS EN 9300-011-2013 Aerospace series LOTAR Long Term Archiving and Retrieval of digital technical product documentation such as 3D CAD and PDM data Reference process description D.pdf

《BS EN 9300-011-2013 Aerospace series LOTAR Long Term Archiving and Retrieval of digital technical product documentation such as 3D CAD and PDM data Reference process description D.pdf》由会员分享，可在线阅读，更多相关《BS EN 9300-011-2013 Aerospace series LOTAR Long Term Archiving and Retrieval of digital technical product documentation such as 3D CAD and PDM data Reference process description D.pdf（18页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN 9300-011:2013Aerospace series LOTARLong Term Archiving andRetrieval of digital technicalproduct documentation such as3D, CAD and PDM dataPart 011: Reference process descrip

2、tion“Data preparation“BS EN 9300-011:2013 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 9300-011:2013.The UK participation in its preparation was entrusted to TechnicalCommittee ACE/1, International and European Aerospace Policy andProcesses.A list of organiza

3、tions represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2013. Published by BSI StandardsLimited 2013ISBN

4、978 0 580 55802 3ICS 01.110; 35.240.30; 35.240.60; 49.020Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 28 February 2013.Amendments issued since publicationDate T

5、ext affectedBS EN 9300-011:2013EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 9300-011 January 2013 ICS 01.110; 35.240.30; 35.240.60; 49.020 English Version Aerospace series - LOTAR Long Term Archiving and Retrieval of digital technical product documentation such as 3D, CAD and PDM data - Part

6、 011: Reference process description “Data preparation“ This European Standard was approved by CEN on 24 November 2012. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without

7、any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other lang

8、uage made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmar

9、k, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE F

10、OR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2013 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 9300-011:2013: EBS EN 9300-011:2013EN 9300-0

11、11:2013 (E) 2 Contents Page Foreword 3 Introduction .4 1 Scope 5 2 Normative references 5 3 Terms, definitions and abbreviations 5 4 Applicability 5 5 Data preparation 6 6 Detailed process steps description .6 6.1 General 6 6.2 Select data for archiving .6 6.3 Initiate quality agent 7 6.4 Data verif

12、ication .7 6.5 Automatic creation of Validation properties? .7 6.6 Automatic creation of Validation properties .8 6.7 Create PDI .8 6.8 Create Descriptive Information 9 6.9 Create SIP .9 6.10 Manual creation Validation properties 9 6.11 Error handling for data preparation 10 7 Support process step:

13、Preservation Planning 10 8 Data Descriptions . 10 8.1 General . 10 8.2 Involved roles 10 8.3 Involved data . 11 9 Definition Transfer to Data Generation (Milestone) 12 Bibliography . 13 Figure 1 Data preparation process .6 BS EN 9300-011:2013EN 9300-011:2013 (E) 3 Foreword This document (EN 9300-011

14、:2013) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services

15、of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by July 2013, and conflicting national standards shall be withdrawn at the latest by

16、July 2013. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards o

17、rganisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembou

18、rg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 9300-011:2013EN 9300-011:2013 (E) 4 Introduction This European Standard was prepared jointly by ASD-STAN and the PROSTEP iViP Association. The PROSTEP iViP

19、Association is an international non-profit association in Europe. For establishing leadership in IT-based engineering it offers a moderated platform to its nearly 200 members from leading industries, system vendors and research institutions. Its product and process data standardization activities at

20、 European and worldwide levels are well known and accepted. The PROSTEP iViP Association sees this European Standard and the related parts as a milestone of product data technology. Users should note that all European Standards undergo revision from time to time and that any reference made herein to

21、 any other standard implies its latest edition, unless otherwise stated. BS EN 9300-011:2013EN 9300-011:2013 (E) 5 1 Scope This European Standard provides a detailed description for the recommended data preparation process for archiving of 3D and PDM data, as overviewed in EN 9300-010. 2 Normative r

22、eferences The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applie

23、s. EN 9300-003, Aerospace series LOTAR Long Term Archiving and Retrieval of digital technical product documentation such as 3D, CAD and PDM data Part 003: Fundamentals and concepts EN 9300-007, Aerospace series LOTAR Long Term Archiving and Retrieval of digital technical product documentation such a

24、s 3D, CAD and PDM data Part 007: Terms and References 1)EN 9300-010, Aerospace series LOTAR Long Term Archiving and Retrieval of digital technical product documentation such as 3D, CAD and PDM data Part 010: Overview Data Flow 1)ISO 14721:2003, Space data and information transfer systems Open archiv

25、al information system Reference model OAIS 3 Terms, definitions and abbreviations For the purposes of this document, the terms, definitions and abbreviations given in EN 9300-007 apply. 4 Applicability EN 9300-011 is applicable to new 3-D product data records and may be applicable to existing 3D pro

26、duct data records, on current and earlier products, produced using previous regulations, standards and procedures. The current version is focused on product data as defined in the domain specific parts. 1) Published as ASD-STAN Prestandard at the date of publication of this standard (www.asd-stan.or

27、g). BS EN 9300-011:2013EN 9300-011:2013 (E) 6 5 Data preparation See Figure 1. Figure 1 Data preparation process The data to be archived will be prepared by the producer. This includes a defined data verification, performed by a Quality Agent tool. The data verification will test the data against de

28、fined data quality requirements, and will provide a result report. Data preparation also includes the creation of Validation properties. The sub process shall be certified. Output data: Submission Information Package (SIP), reset archiving trigger information, process control data, error fixing repo

29、rt. 6 Detailed process steps description 6.1 General Input and output data described in this standard represent the minimal requirements for the fulfilment of the process steps. Additional data may be added, but shall match at a minimum the requirements for the information package (see EN 9300-003,

30、Section 5.3.2.1 “Definition of the core model”). 6.2 Select data for archiving The producer selects data for archiving during, for example, a domain depended release process (this is outside the scope of EN 9300). As an example, the selection can be performed at a product structure viewer of a CAD/P

31、DM system. The process step represents the initial trigger for the archiving process. The selected e.g. CAD or PDM information defines the Content Information (CI) of the future SIP. BS EN 9300-011:2013EN 9300-011:2013 (E) 7 Input data: CI; error report for producer of process step number 10: error

32、handling for data preparation; process control data. Output data: CI. 6.3 Initiate quality agent The producer will trigger the process manually. The system tool “quality agent“ automatically creates Validation properties from the data and checks if the data meets with the recommended data quality cr

33、iteria. It is recommended that the process step is synchronised with the producers own release process. Input data: CI. Output data: CI. 6.4 Data verification Whereas the purpose of validation is to ensure that the right information has been captured, the intention of verification is to ensure that

34、the data is correctly represented. Verification rules shall ensure that a data representation meet the quality requirements within defined tolerances. Verification is successful if no verification rule is violated. The verification rules are domain specific and are defined within EN 9300 (for exampl

35、e, verification rules for CAD are described in the 100 series parts of EN 9300). Only verification rules belonging to the core models are part of EN 9300. The down stream processes and the data outputs are determined by the result of the “data verification”. Input data: CI; data quality rules. Outpu

36、t data: If data verification is successful: CI; reference to Results report (the integration of this information into the Descriptive Information is optional); Results report. If data verification fails: data preparation error report. 6.5 Automatic creation of Validation properties? The producer has

37、 to decide if a manual or automatic creation of Validation properties is possible. Input data: CI. BS EN 9300-011:2013EN 9300-011:2013 (E) 8 Output data: CI. 6.6 Automatic creation of Validation properties The Producer initiates the source system to calculate Validation properties automatically. The

38、 Validation properties are used later for validation within the process step “INGEST Generate AIP“. Possible Validation properties are: Validation properties for 3D CAD Data, e.g. weight, centre of gravity, etc.; Validation properties for PDM product structure information; (future: Validation proper

39、ties for CAx and electric harness, etc.). It is recommended that Validation properties be extracted from the Content Information directly. Alternatively, Validation properties can be generated manually and saved within the Preservation Description Information (PDI). The sub processes detailing the s

40、pecific actions in case of failure or success of the creation of Validation properties are not represented. Where needed, they will be detailed in the recommended practices associated with part 11. Input data: CI; Validation property rules data. Output data: CI; Validation properties. 6.7 Create PDI

41、 The producer creates the Preservation Description Information (PDI). The PDI is the information which is necessary for adequate preservation of the Content Information and which can be categorised as Provenance, Reference, Fixity, and Context information. As an addition for EN 9300, the producer sh

42、all integrate Validation properties information into the PDI to ensure the existence of Validation Properties for later automatic validation processes. A further addition belongs to the Proprietary Rights: product data may be covered by proprietary rights that shall be protected. All information tha

43、t the Producer wishes to declare as proprietary shall be identified as proprietary. Information regarding proprietary rights shall be associated with the product data to assure the information is appropriately marked to provide the protection warranted such product data. PDI is categorised as: Prove

44、nance: the integrity of an information object is partly embodied in tracing where it came from. To preserve the integrity of an information object, digital archives shall preserve a record of its origin and chain of custody. Reference: provides one or more identifiers, or systems of identifiers, by

45、which the Content Information may be uniquely identified. Fixity: if an object is not fixed, and the content is subject to change or withdrawal without notice, then its integrity may be compromised. Fixity information prevents such change. BS EN 9300-011:2013EN 9300-011:2013 (E) 9 Context: Context d

46、escribes how the Content Information relates to other information outside the Information Package. For example, it would describe why the Content Information was produced, and it may include a description of how it relates to another Content Information object. Input data: Validation properties; Res

47、ults report. Output data: If creation of PDI is successful: PDI. If creation of PDI fails: Reset archiving trigger information. 6.8 Create Descriptive Information The producer creates a set of Descriptive Information (DI), which includes archive meta data meeting the archives requirements (according

48、 to ISO 14721:2003 OAIS). The descriptive information includes a reference to the data verification results report. Input data: Results report, as reference information. Output data: DI. 6.9 Create SIP The producer creates a SIP by combining the DI, PDI and CI into one package. The SIP contains also

49、 Packaging Information (PI). The PI is that information which, either actually or logically, binds, identifies and relates the CI and PDI. The SIP will be transferred to the archive. The formats of the packages are defined in a submission agreement between the producer and the archive. Input data: CI; PDI; DI; PI. Output data: SIP. 6.10 Manual creation Validation properties The producer shall be able to create a set of predefined Validation properties manua