BS 7961-2004 Specification for a device for measuring the static vertical mass (noseweight)at the coupling point of the towed vehicle《挂车耦合点的静态垂直质量(牵引杆施加于牵引车的垂直载荷)测量设备规范》.pdf

《BS 7961-2004 Specification for a device for measuring the static vertical mass (noseweight)at the coupling point of the towed vehicle《挂车耦合点的静态垂直质量(牵引杆施加于牵引车的垂直载荷)测量设备规范》.pdf》由会员分享，可在线阅读，更多相关《BS 7961-2004 Specification for a device for measuring the static vertical mass (noseweight)at the coupling point of the towed vehicle《挂车耦合点的静态垂直质量(牵引杆施加于牵引车的垂直载荷)测量设备规范》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARDBS 7961:2004Specification for a device for measuring the static vertical mass (noseweight) at the coupling point of a towed vehicleICS 17.060; 43.040.70; 43.100g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g

2、3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58Confirmed December 2009BS 7961:2004This British Standard was published under the authority of the Standards Policy and Strategy Committee on 27 January 2004 BSI 27 January 2004The following BSI references relate to the work

3、on this British Standard:Committee reference AUE/8Draft for comment 00/704997 DC ISBN 0 580 43114 2Committees responsible for this British StandardThe preparation of this British Standard was entrusted to Technical Committee AUE/8, Undergear for caravans and light trailers, upon which the following

4、bodies were represented:Camping and Caravanning Club LimitedCaravan ClubConsumer Policy Committee of BSIDfT Central Transport GroupNational Caravan Council LimitedNational Trailer and Towing Association LimitedSociety of Motor Manufacturers and Traders LimitedTrailer and Towing Advisory ServiceAmend

5、ments issued since publicationAmd. No. Date CommentsBS 7961:2004 BSI 27 January 2004iContentsPageCommittees responsible Inside front coverForeword ii1Scope 12Terms and definitons 13 The noseweight gauge 14 Test for the determination of durability 45 Test for the determination of overload 46 Test for

6、 the determination of accuracy 5Bibliography 7Figure 1 Coupling 3BS 7961:2004ii BSI 27 January 2004ForewordThis British Standard has been prepared by AUE/8, Undergear for caravans and light trailers.This publication does not purport to include all the necessary provisions of a contract. Users are re

7、sponsible for its correct application.Compliance with a British Standard does not of itself confer immunity from legal obligations.Summary of pagesThis document comprises a front cover, an inside front cover, pages i and ii, pages 1 to 7 and a back cover.The BSI copyright notice displayed in this do

8、cument indicates when the document was last issued.BS 7961:2004 BSI 27 January 200411 ScopeThis British Standard specifies requirements for devices intended to measure the static vertical mass of towed vehicles. Such devices are commonly known as “noseweight gauges”.This British Standard only applie

9、s to all towed vehicles up to 3 500 kg maximum technical permissible laden mass.NOTE Normally such towed vehicles are fitted with a 50 mm ball coupling device but the manufacturer of a noseweight gauge may also specify its suitability for use with other coupling devices.2 Terms and definitionsFor th

10、e purposes of this British Standard, the following terms and definitions apply.2.1 ball coupling systemmechanical coupling system designed to connect towing vehicles and towed vehicles by means of a coupling ball2.2 coupling headmechanical device on the drawbar or overrun device of towed vehicles fo

11、r connection to a coupling ball2.3 noseweightstatic vertical mass (“S” value in kg) exerted on the towing vehicle by the towed vehicle at the coupling pointNOTE Static vertical mass is commonly referred to as the S value in the UK and Europe. See Directive 94/20/EEC 1 and UNECE Regulation No. 55 2 f

12、or further information.2.4 towing vehiclemechanically propelled vehicle used for towing a towed vehicle2.5 towed vehiclevehicle without any means of self-propulsion to be towed by a towing vehicle (e.g. caravan, horse-box, etc.)3 The noseweight gauge 3.1 RangeThe noseweight gauge shall be capable of

13、 measuring from 20 kg to at least 100 kg.The noseweight gauge shall be capable of measuring in increments not greater than 5 kg and in the case of an analogue device the minimum scale separation for a 5 kg increment shall not be less than 5 mm. NOTE The scale and marked numerical values should be cl

14、ear and easy to read.BS 7961:20042 BSI 27 January 20043.2 PerformanceNOTE The same noseweight gauge should be used in performing each of the following three tests. If the noseweight gauge fails at any stage, then no further testing should be carried out.3.2.1 DurabilityWhen tested in accordance with

15、 Clause 4, the noseweight gauge shall be able to complete 1 000 test cycles and continue to meet the accuracy requirements of 3.2.3.3.2.2 Overload testingAfter being tested in accordance with Clause 4, the noseweight gauge shall be able to withstand twice the maximum load specified by the device man

16、ufacturer, for a period of 30 s, without permanent damage when tested in accordance with Clause 5. After removal of the load, the noseweight gauge shall show no deformation.3.2.3 AccuracyHaving undergone the tests described in Clause 4 and Clause 5, the noseweight gauge shall be accurate to within 5

17、 kg or 10 % of the specified mass, whichever is least.3.3 Operating height rangeThe operating height range of the noseweight gauge shall be as specified in the manufacturers user instructions.3.4 FinishAll surfaces of the noseweight gauge shall be smooth and free from any burrs or sharp edges that c

18、ould cause injury.3.5 MarkingsAll noseweight gauges shall be permanently and legibly marked with the following information:a) the weight range, kg to kg;b) the operating height range mm to mm to the centre of rotation of the coupling device in relation to the ground see Figure 1a) and Figure 1b);c)

19、the number and date of this British Standard, i.e. BS 7961:2004;d) the manufacturers name or trade mark;e) reference to the user instructions (see 3.6).3.6 User instructionsEach noseweight gauge shall be supplied with user instructions that shall contain at least the following information:a) detaile

20、d instructions for use;b) recommendations for safe operation of the device;c) recommendations for maintenance, storage and re-calibration.The instructions shall include the following statement:“When assessing/adjusting the noseweight of the towed vehicle, the limiting noseweights that individual com

21、ponents are able to sustain should be taken into account as well as those that the towed vehicle can sustain. The following components should all have limits of noseweight specified by the manufacturer, and any other limiting factors should also be considered in the assessment/adjustment of the nose

22、weight of the towed vehicle:a) towing vehicle;b) vehicle mounted towing device (tow bar);c) towed vehicle mounted towing device (coupling assembly);d) towed vehicle drawbar assembly;e) towed vehicle.”BS 7961:2004 BSI 27 January 20043Key1 is the vehicle2 is the center of rotation3 is the range of ope

23、rating height from the centre of rotation to the grounda) Coupling ballKey1 is the vehicle2 is the center of rotation3 is the towed vehicle drawbar4 is the range of operating height from the centre of rotation to the groundb) Coupling jaw and eyeFigure 1 Coupling1231324BS 7961:20044 BSI 27 January 2

24、0044 Test for the determination of durability4.1 PrincipleThe noseweight is operated in cycles from an S value of zero to the maximum specified for the noseweight gauge under test and back again to an S value of zero. The gauges ability to successfully complete a given number of test cycles is taken

25、 as a measure of its durability.4.2 Apparatus4.2.1 test rig, with a suitable means of force application so that it is not subjected to any additional forces or moments apart from an S value commensurate with the maximum specified for the noseweight gauge under test.4.2.2 noseweight gauge.4.3 Initial

26、 inspection of the noseweight gaugePrior to the start of the test check the noseweight gauge for any deformation.4.4 ProcedureSet up the test rig to apply the specified test forces to the noseweight gauge. Perform the load/unload cycle from an S value of zero to the maximum specified for the nosewei

27、ght gauge under test and back again to an S value of zero. Repeat the load/unload cycle at a frequency of not greater than 1 Hz until a minimum of 1 000 cycles have been completed.4.5 Final inspection of the noseweight gaugeCheck the noseweight for any deformation. If there is no obvious deformation

28、, undertake the overload test described in Clause 5.4.6 Expression of resultsRecord the number of test cycles completed without failure. If 1 000 or more test cycles have been successfully completed, record a “PASS”. If less than 1 000 test cycles have been completed, record a“FAIL”.4.7 Test reportT

29、he test report shall include the following:a) reference to this British standard, i.e. BS 7961:2004;b) the test result recorded in accordance with 4.6;c) the date of the test;d) where the test took place.5 Test for the determination of overload5.1 PrincipleFollowing testing in accordance with Clause

30、 4, the noseweight gauge is loaded to twice the maximum specified S value for the noseweight under test for a measured time and inspected for signs of deformation and damage. The gauges ability to successfully complete a given number of test cycles without deformation is taken as a measure of its du

31、rability.BS 7961:2004 BSI 27 January 200455.2 Apparatus5.2.1 test rig, with a suitable means of force application so that it is not subjected to any additional forces or moments apart from an S value commensurate with the maximum specified for the noseweight gauge under test.5.2.2 noseweight gauge.5

32、.3 Initial inspection of the noseweight gaugePrior to the start of the test, check the noseweight gauge for any deformation. If there is any deformation, do not proceed with the test.5.4 ProcedureSet up the test rig to apply the test force to the noseweight gauge. Maintain twice the maximum specifie

33、d S value for the noseweight under test for a period of 30 s and then release. 5.5 Final inspection of the noseweight gaugeCheck the noseweight for any deformation. If there is no obvious deformation, undertake the accuracy test described in Clause 6.5.6 Expression of resultsRecord any visible chang

34、es shown between the initial and final inspections of the noseweight gauge. If there is no obvious deformation, record a “PASS”. If there is obvious deformation, record a “FAIL”.5.7 Test reportThe test report shall include:a) reference to this British Standard, i.e. BS 7961:2004;b) the result of the

35、 test in accordance with 5.6;c) the date of the test;d) where the test took place.6 Test for the determination of accuracy6.1 PrincipleAfter the noseweight gauge has been successfully tested in accordance with the tests described in Clause 4 and Clause 5, test forces of one-third, two-thirds and the

36、 maximum specified S value for the noseweight gauge under test are applied and the results indicated by the noseweight gauge are analysed for conformance with 3.2.3.6.2 Apparatus6.2.1 test rig, with a suitable means of force application so that it is not subjected to any additional forces or moments

37、 apart from an S value commensurate with the maximum specified for the noseweight gauge under test.6.2.2 noseweight gauge.6.3 Initial inspection of the noseweight gaugePrior to the start of the test, check the noseweight gauge for any deformation. If there is any deformation, do not proceed with the

38、 test.6.4 ProcedureApply each force to the noseweight gauge. Note the reading of each force.BS 7961:20046 BSI 27 January 20046.5 Final inspection of the noseweight gaugeCheck the noseweight for any deformation.6.6 Expression of resultsRecord the weight of each test force and the reading taken from t

39、he noseweight gauge. Calculate the variance between each applied force and the indicated reading taken from the noseweight gauge.6.7 Test reportThe test report shall include:a) reference to this British Standard, i.e. BS 7961:2004;b) the result of the test in accordance with 6.4;c) the date of the t

40、est;d) where the test took place.BS 7961:2004 BSI 27 January 20047Bibliography 1 Directive 94/20/EC of the European Parliament and of the Council of 30 May 1994 relating to the mechanical coupling devices of motor vehicles and their trailers and their attachment to those vehicles. Official Journal L

41、 195, 29/07/1994, p. 00010060.2 UNECE (Economic Commission for Europe of the United Nations) Regulation No. 55, Agreement Concerning the Adoption of Uniform Conditions of Approval and Reciprocal Recognition of Approval for Motor Vehicle Equipment and Parts. Geneva, 20 March 1958.BS 7961:2004BSI389 C

42、hiswick High RoadLondonW4 4ALBSI British Standards InstitutionBSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by

43、 amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standa

44、rd would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive th

45、e latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-.In

46、response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European and international standards thro

47、ugh its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-.Subscribing members of

48、BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-.Information regarding online

49、access to British Standards via British Standards Online can be found at http:/www.bsi- information about BSI is available on the BSI website at http:/www.bsi-.CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in an