AWS D1 1 D1 1M ERTA 2-2016 Structural Welding Code - Steel (23rd Edition 2nd printing).pdf

《AWS D1 1 D1 1M ERTA 2-2016 Structural Welding Code - Steel (23rd Edition 2nd printing).pdf》由会员分享，可在线阅读，更多相关《AWS D1 1 D1 1M ERTA 2-2016 Structural Welding Code - Steel (23rd Edition 2nd printing).pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、 The purpose of an errata sheet is to notify the public that a published standard has a typographical error. Errata sheets provide a list of errors and their corrections on an AWS standard introduced during the publication stages. (Errata Notice: 03/01/2016) AWS Errata Sheet The following Errata hav

2、e been identified and will be incorporated into the next reprinting of AWS D1.1/D1.1M:2015, Structural Welding Code-Steel Page 38, Figure 2.4 references in title: replace (see 2.9.9.1 and 2.9.1.2) with (see 2.9.1.1 and 2.9.1.2) Page 54, Table 3.2Base Metal Group I, Column heading A5.29a Low-Alloy St

3、eel: replace “E6XT-XM” with “E6XTX-XM” Page 72, Figure 3.2; the Tolerance Columns in the Table were aligned with the Root Opening Root Face Bend Radius Column Page 73, Figure 3.2; the Tolerance Columns in the Table were aligned with the Root Opening Root Face Bend Radius Column Page 80, Figure 3.2;

4、the Tolerance Columns in the Table were aligned with the Root Opening Root Face Bend Radius Column Page 81, Figure 3.2; the Tolerance Columns in the Table were aligned with the Root Opening Root Face Bend Radius Column Page 89, Figure 3.3, Double-bevel-groove weld (5), Butt joint (B); the Tolerance

5、Columns in the Table were aligned with the Root Opening Root Face Bend Radius Column Page 89, Figure 3.3, Double-bevel-groove weld (5), Butt joint (B), As Detailed (see 3.13.1) Column; replace “ + 10” with “ + =” Page 89, Figure 3.3, Double-bevel-groove weld (5), Butt joint (B), As Detailed (see 3.1

6、3.1) Column; replace “0” with “+ 10, 0” Page 89, Figure 3.3, Double-bevel-groove weld (5), Butt joint (B), As Fit-Up (see 3.13.1) Column; replace “ + 10” with “ + =” Page 89, Figure 3.3, Double-bevel-groove weld (5), Butt joint (B), As Fit-Up (see 3.13.1) Column; replace “5” with “+ 10, 5” Page 105,

7、 Figure 3.5: Note “a” replace “5.14” with “5.13” The purpose of an errata sheet is to notify the public that a published standard has a typographical error. Errata sheets provide a list of errors and their corrections on an AWS standard introduced during the publication stages. (Errata Notice: 03/01

8、/2016) Page 105, Figure 3.5: Note “a” replace “Table 3.7” with Table “3.6” Page 105, Figure 3.5: Note “b” replace “5.22.1” with “5.21.1” Page 105, Figure 3.5: replace “ALL DIMENSIONS IN mm” with “ALL DIMENSIONS IN inches” Page 105, Figure 3.5: replace welding process “FMAW” with “GMAW” Page 106, Fig

9、ure 3.5: added to the top of page “See Notes on Page 105” Page 106, Figure 3.5: replace welding process “FMAW” with “GMAW” Page 134, Table 4.9, Note 2, replace “20 ftlbs 27.1 J” with “20 ftlbf 27 J” Page 135, Table 4.10: replace title “Welder and Welding Operator QualificationProduction Welding Posi

10、tions Qualified by Plate, Pipe, and Box Tube Tests (see 4.15.1)” with “Welder and Welding Operator QualificationProduction Welding Positions Qualified by Plate Tests (see 4.15.1)” Page 139, Table 4.14: add a vertical line between Welding Process and Test Location Page 149, Figure 4.10, footnote b, r

11、eplace 0.004 in 0.102 mm with “0.004 in 0.1 mm” Page 149, Figure 4.10, footnote b, replace 0.015 in 0.381 mm with “0.015 in 0.38 mm” Page 177, 5.23.3: replace “Groove weld reinforcement shall comply with Tables 5.8, and 5.9 and with the provisions below” with “Groove weld reinforcement shall comply

12、with Tables 5.8 and 5.9 and with the provisions below” Page 198, 6.17.7: add an additional sentence to the subclause “Steel backing shall not be considered part of the weld or weld reinforcement in IQI selection.” Page 245, 7.2.6: replace “ASTM A29, Standard Specification for Steel Bars, Carbon and

13、Alloy, Hot-Wrought, General Requirements for Grades 1010 through 1020” with “ASTM A29/A29M-12e1, Standard Specification for General Requirements for Steel Bars, Carbon and Alloy, Hot-Wrought, Grades 1010 through 1020” Page 283, Table 9.10: replace column heading “Nominal Pipe or Tube Wall Thicknessb

14、, c Qualified, in”: with “Nominal Plate, Pipe or Tube Wall Thicknessb, c Qualified, in” The purpose of an errata sheet is to notify the public that a published standard has a typographical error. Errata sheets provide a list of errors and their corrections on an AWS standard introduced during the pu

15、blication stages. (Errata Notice: 03/01/2016) Page 283, Table 9.10, footnote b: replace “For square groove welds that are qualified without backgouging, the maximum thickness qualified shall be limited to the plate thickness” to “For square groove welds that are qualified without backgouging, the ma

16、ximum thickness qualified shall be limited to the test thickness” Page 284, Table 9.10: replace column heading “Nominal Pipe or Tube Wall Thicknessb, c Qualified, mm”: with “Nominal Plate, Pipe or Tube Wall Thicknessb, c Qualified, mm” Page 287, Table 9.14; Tests on Pipe or Tubing: replace column he

17、ading “Nominal Plate, Pipe, or Tube Wall ThicknessdQualified, in” with “Nominal Plate, Pipe or Tube Wall Thicknessd Qualified, in” Page 287, Table 9.14, Production T-, Y-, or K-Connection Fillet Welds, Type of Test Weld Column, Option 1Fillet: replace (Fig. 4.26)gwith (Fig. 4.25)gPage 287, Table 9.1

18、4, Production T-, Y-, or K-Connection Fillet Welds, Type of Test Weld Column, Option 1Fillet: replace (Fig. 4.23)gwith (Fig. 4.22)gPage 288, Table 9.14: replace far left column heading “Tests on Pipe or Tubinge” with “Tests on Pipe or Tubingf” Page 420, Q3(15): Made all the language contained after

19、“Documentation retention requirements.” a new paragraph within Q3(15). Page 502, C-4.8: replace the sentence “However, departure from variables which affect the mechanical or chemical composition of material properties, or soundness of the weldment is allowed without requalification.” with “However,

20、 departure from variables which affect the mechanical or chemical composition of material properties, or soundness of the weldment is not allowed without requalification.” Page 590, IndexElectrodes, welder qualification groups: replace “Table 9.15” with “Table 4.13” Page 591, IndexFiller Metals, wel

21、der group designation: replace “4.3.2.1” with “4.2.3.1, Table 4.13” Page 591, IndexFillet Welds, maximum size: replace “2.4.2.8” with “2.4.2.9” Page 591, IndexFillet Welds, test plates: replace “4.4” with “4.12.2, Table 4.4” The purpose of an errata sheet is to notify the public that a published sta

22、ndard has a typographical error. Errata sheets provide a list of errors and their corrections on an AWS standard introduced during the publication stages. (Errata Notice: 03/01/2016) Page 594, IndexOverlap: replace “5.25.11” with “5.25.1.1” Page 594, IndexPrequalified joint details: replace “22.3.5.

23、4” with “2.3.5.4” Page 595, IndexRadiographs, disposition: replace “6.19” and “C-6.19” with “6.18” and C-6.18” respectively Page 595, IndexRadiography: replace “6.19.3 and C-6.19.3” with “6.18.3 and C-6.18.3” respectively Page 596, IndexSkewed T-joints: replace “Figure 3.44” with “Figure 3.4” Page 596, IndexStatically Loaded Structures, backing: replace “2.6.4.1” with “5.9.1.5” Throughout the document: replace “ftlbs” or “ftlb” with “ftlbf”